@article { author = {Fasola, S.H. and Mawjoud, S.A.}, title = {Performance Evaluation of Soft Handover in WCDMA System}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {1-14}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26582}, abstract = {Abstract In this paper soft handover parameters in WCDMA system are investigated. They include the effect of imperfect power control on the downlink capacity and power assignment to the mobile station, the micro diversity gain which represents the gain in the downlink direction, and the macro diversity gain which represents the gain in the uplink direction. The results showed that the power control error increases the total power consumption by the mobile station which leads to decrease the capacity (number of users per cell). Soft handover decreases the fade margin which leads to improve the coverage area. During soft handover the mobile station needs lower signal to noise ratio compared with no soft handover to obtain the specific bit error rate. Keyword: Cellular Mobile System, Soft Handover (SHO), Power Control.}, keywords = {Keyword,Soft Handover,Power Control}, title_ar = {تقییم أداء المناقلة السلسة فی نظام WCDMA}, abstract_ar = {الخلاصةفی هذا البحث تم تقییم معاملات المناقلة السلسة فی نظام .WCDMAهذه المعاملات تشمل تأثیر السیطرة غیر المثالیة للقدرة على السعة فی الاتصال النازل(من المحطة الرئیسیة BS إلى المحطة المتنقلة MS) وتخصیص القدرة للمحطة المتنقلة MS، إن کسب التنوع من الخلیة الماکرو والذی یمثل الکسب فی الاتصال النازل وکذلک کسب التنوع والّذی یمثل الکسب فی الاتصال الصاعد(من المحطة المتنقلة MS إلى المحطة الرئیسیة BS). أظهرت النتائج إن الخطأ فی السیطرة على القدرة یؤدی إلى الزیادة فی استهلاک القدرة الکلیة للمحطة المتنقلة(MS) والذی یؤدی إلى تقلیل السعة (عدد المستخدمین لکل الخلیة). المناقلة السلسة تقلل هامش الخفوت مما یؤدی إلى زیادة منطقة التغطیة. خلال المناقلة السلسة فان المحطة المتنقلة تحتاج إلى نسبة الإشارة إلى الضوضاء اقل مقارنة مع مناقلة غیر سلسة للحصول على معدل خطأ محدد.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26582.html}, eprint = {https://rengj.mosuljournals.com/article_26582_e2ad0e7a0daa86f94d6af40dfffe0761.pdf} } @article { author = {A.Saleh, Aasef. and M.Saied, Basil and I.Zynal, Hussein}, title = {AC Current Harmonics Reduction& improve the power factor for Single Phase controlled Rectifiers Using Current Injection Method}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {1-15}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26565}, abstract = {Abstract The AC electrical distribution system works at limited values of voltage and frequency levels. The increase of using non linear loads and loads those connected by electronic keys produces non sinusoidal voltages and currents in the distribution systems. Single and three phase, controlled and uncontrolled rectifiers, are used for obtaining DC current and voltage. This affect the shape of the supply current which included many harmonics. The quality and quantity of the power obtained are affected as a result. The shape of the current wave is therefore attracted the attention of many researcher groups. The line injection by current harmonics is one of the most important and effective techniques used for such treatment. The aim of this research work is to reduce the harmonics in the input current and improving the power factor of the single phase, controlled and uncontrolled, rectifiers. This is usually carried out by employing injection method technique with reversible polarity through connecting a passive resonance circuit between the input and output of the rectifier. The passive resonance circuit creates second harmonic current which will circulate between the AC and DC sides of the rectifier and decreases the total harmonic distortion (THD). In this work, the ratio of (THD) is reduced from 50% to 10% with power factor increased nearly to unity for different values of the trigger angle (α).}, keywords = {}, title_ar = {تقلیل توافقیات التیار مع تحسین عامل القدرة للمقومات أحادیة الطور المحکومة بتقنیة حقن توافقیات التیار}, abstract_ar = {}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26565.html}, eprint = {https://rengj.mosuljournals.com/article_26565_fce8c00991438447100a9ff761263403.pdf} } @article { author = {Asaad M. Jassim Al-Hindawi, Dr. and M. Al- Ali, Suhair}, title = {Theoretical and Experimental Results of Substrate Effects on Microstrip Power Divider Designs}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {15-25}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26603}, abstract = {ABSTRACT The effects of substrate materials on the design of microstrip power divider are investigated theoretically and experimentally. Three different dielectric substrate materials are chosen ; Duriod 3003, G10/FR4 epoxy Glass and Duriod 3010 to be studied. A three-way double-stage power divider is designed at S-band frequency of 2.25 GHz and etched on each studied substrate separately. The substrate effects of large difference in dielectric constant and the dissipation factor ; on the characteristics and performance of the microsrip circuits are taken into consideration in the present study. The circuit designs presented here, are analyzed using the Genesys CAD program and implemented and tested experimentally. The simulated and measured results are compared , discussed and indicate that significant changes in the characteristics of the microstrip power divider are observed.}, keywords = {KEYWORD,microstrip line,VSWR,isolation loss}, title_ar = {النتائج النظرية والعملية لتأثيرات طبقة الأساس في تصاميم موزعات القدرة ذات الاشرطة الدقيقة}, abstract_ar = {الملخص تم بحث تأثيرات طبقة الأساس على تصاميم موزعات القدرة ذات الاشرطة الدقيقة نظريا وتجريبيا. تم اختيار ثلاث قواعد وهي: ديورويد 3003 , الزجاج الأبوكسي نوع G10/FR4 وديورويد 3010. وقد صممت ثلاثة موزعات قدرة مختلفة تختلف بأختلاف القاعدة حيث يتكون الواحد منها من مرحلتين وبثلاثة مخارج . وقد تم تصميم هذه الموزعات لتعمل عند التردد2.25 GHz من الحزمة الترددية S . لقد تم تحليل الدوائر المصصمة الثلاث بأستخدام برنامج Genesys CAD وبعدها تم تصنيعها وفحصها عمليا. تم مقارنة النتائج المستحصلة ومناقشتها وقد لوحظ بأن هناك تغييرات واضحة بخواص هذه الموزعات.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26603.html}, eprint = {https://rengj.mosuljournals.com/article_26603_5f3d931d992786e49de2b8b9d7b116eb.pdf} } @article { author = {S. Al - Dabbagh, Mohammad and Adnan M. Al Saffawi, Dr.}, title = {A Study For Refrigerant's Characteristics to Choose the Optimum For Ejector Refrigeration System}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {16-29}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26568}, abstract = {Abstract Refrigeration systems needs efficient refrigerant to perform it's determined objective, so, an optimum refrigerant, must have a good and desirable characteristics as compared with other refrigerants as well as a high coefficient of performance for the working cycle, which results for minimizing operating power to attain determined refrigeration capacity. A variety kinds of improved refrigerants had been appeared within the last twenty years, and many countries did large efforts to phaseout some refrigerants, or at least reduce it's usage, that's for it's ozone layer depletion and it's bad influence on environment and climate. This research deals with a comparative study between many Refrigerants on the basis of it's characteristics , COP and compressibility factor in ejector refrigeration system to select the optimum to be used in this system. From this study results , the optimum refrigerant is Butane (R – 600), which have a good characteristics , a relatively high compressibility factor values , and a COP value of (0.615) , which is a good result as compared with other refrigerants included the phaseouted for it's bad influence on environment and climate.}, keywords = {KEYWORDS,optimum refrigerant,Ejector,Refrigeration System}, title_ar = {دراسة صفات موائع التثلیج واختیار الأمثل لنظام تثلیج یعمل بالقاذف}, abstract_ar = {الخلاصةان أنظمة التثلیج تحتاج الى مائع کفوء یؤدی عمله المحدد ، إلا أن الحصول على مائع تثلیج أمثل مناط بوجود صفات جیدة ومرغوبة فیه تمیزه عن غیره من الموائع ، وتسهم فی ارتفاع معامل الأداء للدورة التی یقوم بتشغیلها ، وبالنتیجة تقلیل القدرة اللازمة للتشغیل وتحقیق سعة التثلیج المطلوبة .وقد ظهرت أنواع مختلفة من موائع التثلیج خلال العقدین الماضیین ، وهناک جهود کبیرة تبذل فی العدید من الدول لاستبعاد بعض من هذه الموائع أو الحد من استخدامها، لتأثیرها على طبقة الاوزون وعلى البیئة والمناخ .تناول البحث إجراء دراسة مقارنة بین مجموعة من موائع التثلیج بالاستناد الى خصائصها ومعامل ادائها ومعامل انضغاطها فی نظام تثلیج یعمل بالقاذف للتوصل الى الامثل للاستخدام فی هذا النظام . ومن نتائج هذه الدراسة یتبین ان مائع التثلیج الامثل هو البیوتان (R – 600) لما یمتلکه من خصائص وممیزات إیجابیة ، وان قیم معامل الانضغاط له عالیة نسبیاً ، وقد بلغ معامل أداءه 0.615 وهی قیمة جیدة نسبة الى الموائع الاخرى لاسیما التی تم التخلی عنها لأضرارها على البیئة والمناخ .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26568.html}, eprint = {https://rengj.mosuljournals.com/article_26568_c5ecec9626251647c64b186635c41429.pdf} } @article { author = {M. Jasim, Museeb and G. Salih, Kamil and E. Majed, Rasha}, title = {Microcontroller Based Maximum Power Point Tracking For Photovoltaic Solar Panel}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {26-39}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26604}, abstract = {Abstract Many papers are published in the past and at present time which operate the solar photovoltaic (PV) panel at its maximum power point, by implementing an analogue or digital electronic circuits which are known as maximum power point trackers (MPPT). The main purpose of the researches are to obtain maximum power from the (PV) solar panel under different atmospheric conditions. In this paper a digital technique based on microcontroller type 8051 is used to design and implement the (MPPT) using maximum power point voltage method. The proposed (MPPT) consists of three major units (i) the solar (PV) panel (ii) the DC/DC step down inverter (iii) the control unit and computation of maximum power point based on microcontroller}, keywords = {}, title_ar = {متتبع نقطة القدرة القصوى للخلايا الشمسية باستخدام المسيطر المصغّر}, abstract_ar = {المستخلصالعديد من البحوث نشرت في الماضي ولا تزال تنشر بخصوص الخلايا الشمسية وتشغيلها في نقطة القدرة القصوى (MPP), وذلك من خلال تصميم الدوائر الالكترونية التناظرية أو الرقمية والتي أطلق عليها متتبعات نقطة القدرة القصوى (MPPT). الهدف من هذه البحوث هو حصول الحمل على أقصى طاقة من الخلايا الشمسية وتحت ظروف مناخية مختلفة. في هذا البحث استخدمت التقنية الرقمية المعتمدة على المسيطر الدقيق نوع (8051) لتصميم وتنفيذ متتبع نقطة القدرة القصوى (MPPT) عن طريق تتبع فولتية نقطة القدرة القصوى للخلية.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26604.html}, eprint = {https://rengj.mosuljournals.com/article_26604_608a09d0d43bc95213cebc8b6b38691c.pdf} } @article { author = {Yassin Shehab, Ahmed}, title = {Effect of Ultrasonic Waves on Sedimentation Characteristics and sludge Dewaterability}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {30-39}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26569}, abstract = {Abstract This paper studied the effect of ultrasonic waves on sedimentation characteristic of activated sludge and there causes on filamentous growth, as well as its effects on the sludge ability dewaterability. The power of ultrasonic waves was set at (0.35W/cm2) while the frequency and contacts time was varied to (31،44،55 KHz) (10،20،30،40 min) respectively. An instrument with (0.5 L) in volume was used to applied ultrasonic waves, it was connected by plastic tube with a completely mixed activated sludge reactor. Testes shows that the relationship between contacts time of ultrasonic and sludge volume index (SVI) was a sagged curve with an optimum point, that’s means there was a specific contacts time to achieved an optimum sedimentation characteristics at specific frequency. As well as Testes shows that the relationship between contacts time and specific resistance (r) was a linear in first order, that’s indicates the ability of dewaterability of sludge decreased with the increasing of ultrasonic contacts time. Also results shows that the effect of ultrasonic waves on activated sludge related conversely with its frequency.}, keywords = {KEYWORDS,Activated Sludge,Sedimentation characteristics,Sludge dewaterablity}, title_ar = {تأثير الأمواج فوق الصوتية على كل من الخصائص الترسيبية وقابلية الحماة لنزع الماء}, abstract_ar = {الخلاصةتناول البحث اختبار قابلية الأمواج فوق الصوتية في تحسين الخصائص الترسيبية للحماة وتمزيق النمو الخيطي فضلا عن دراسة تأثيرها على قابلية الحماة لنزع الماء، وذلك عند تسليط الأمواج بقدرة ثابتة (0.35W/cm2) وترددات متغيرة (KHz 55،44،31) وزمن تعريض متباين ( min40،30،20،10). اُستخدم جهاز مختبري سعة (0.5 L) لتسليط لأمواج فوق الصوتية على الحماة وذلك بربطه مع مفاعل اختباري يعمل بأسلوب الحماة المنشطة ذات المزج التام. أثبتت الاختبارات أن معامل الدليل ألحجمي للحماة (SVI) يرتبط مع زمن التعريض بعلاقة على شكل منحني بنهاية صغرى، حيث تم الحصول على أفضل خصائص ترسيبية للحماة عند زمن تعريض محدد وعند ثبوت التردد. كذلك اثبت اختبار المقاومة النوعية للحماة للاحتفاظ بالماء (r) أن قابلية الحماة لنزع الماء (dewatering) تنخفض كلما ازداد زمن التعريض من خلال ارتباط العاملين بعلاقة خطية من الدرجة الأولى. كما أوضحت نتائج الاختبارات أن شدة تأثير الأمواج على الحماة المنشطة يتناسب عكسياً مع التردد المسلط.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26569.html}, eprint = {https://rengj.mosuljournals.com/article_26569_3eba03e2d2a01e25d80399d1c6ea906f.pdf} } @article { author = {Ahmed Nasser B. Alsammak, Dr.}, title = {Optimal Power Flow Solution with Maximum Voltage Stability}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {40-53}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26606}, abstract = {Abstract This paper presents an Optimal Power Flow (OPF) formulation that is based on multi-objective optimization methodology, which can minimize both of operating costs and losses and it would at same time result in maximizing the distance to voltage collapse. A “Maximum Distance to Voltage Collapse” algorithm, which incorporates constraints on the current operating condition, is firstly presented, while OPF formulations which incorporate voltage stability criteria is secondly presented. The algorithm built on Matlab-Simulink is tested on an IEEE 6-bus test system using a standard power flow model, where the effect of maximum loading point limits is demonstrated.}, keywords = {KEYWORDS,voltage collapse,Optimal Power Flow and Matlab,Simulink}, title_ar = {حل سريان الحمل الأمثل مع أعلى استقرارية للفولتية}, abstract_ar = {المستلخصيقدم هذا البحث صيغة لحل سريان الحمل بطريقة مثلى واعتمادا على أساسيات مهمة بحيث تكون كلفة التشغيل وخسائر النظام اقل ما يمكن وفي نفس الوقت يكون النظام بعيد عن انهيار الفولتية أي بأعلى استقرارية لها. أولاً تم استخدام خوارزمية حساب استقرارية الفولتية في ظروف التشغيل الحالية وبعيداً عن انهيار الفولتية. ثانياً استخدم خوارزمية لحل سريان الحمل بطريقة مثلى مع أعلى استقرارية للفولتية. استخدم برنامج Matlab-Simulink لهذا التحليل مع التطبيق على نموذج نظام ذو ستة عقد مع الأخذ بنظر الاعتبار تأثير أقصى حمل.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26606.html}, eprint = {https://rengj.mosuljournals.com/article_26606_9aacc0aa5910a698de7432bea6242256.pdf} } @article { author = {Aziz Kako, Salim}, title = {Fatigue Behavior of Al – 4wt%Cu / SiCP and Al - 4wt%Cu/ Al2O3P Composites}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {54-61}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26607}, abstract = {Abstract Aluminum – copper ( Al – 4wt%Cu ) alloy metal matrix composites MMCs reinforced with 0.5 ,1.0 ,1.5 % wt of both SiC and Al2O3 particles were fabricated by stir-casting .The effects of SiC and Al2O3 particles content on the fatigue behavior of the Al – 4wt%Cu unreinforced base alloy and the resulted composites were investigated. The results show that fatigue strengths of base alloy increased with increasing weight fractions of ceramic particles and the fatigue strength of MMCs reinforced with SiC particles is higher than that of reinforced with Al2O3 particles}, keywords = {KEYWORDS,Ceramic Particles,Aluminum alloys,fatigue}, title_ar = {Al2O3 و SiC مدعمة بحبيبات ( Al + 4wt%Cu) سلوك الكلل للمواد المتراكبة ذات اساس من سبيكة}, abstract_ar = {الخلاصةيهدف البحث الحالى الى دراسة سلوك الكلل لسبيكة ( Al + 4wt%Cu ) المقواة بدقائق كاربيد السليكون SiC و دقائق الالومينا Al2O3 و بنسب وزنية مختلفة ( 0.5 , 1.0 , 1.5 )% . استخدمت طريقة السباكة بالمزج stir –casting، لتصنيع المواد المتراكبة . بعد ذلك اجريت فحص الكلل على العينات القياسية لكل من سبيكة الاساس و المواد المتراكبة . اظهرت نتائج فحص الكلل ان المادة المتراكبة تمتلك قيم مقاومة الكلال اعلى مقارنة بالسبيكة الاساس و تزداد هذه القيم مع زيادة نسب دقائق السيراميكية المضافة . اما تأثير نوعية المادة السيراميكية على تلك الخاصية فقد لوحظ زيادة ملحوظة في قيم مقاومة الكلل للمادة المتراكبة المقواة بدقائق كاربيد السليكون مقارنة مع المادة المتراكبة المقواة بدقائق الالومينا .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26607.html}, eprint = {https://rengj.mosuljournals.com/article_26607_ccd620effd0bbc14ef657558a6d017a3.pdf} } @article { author = {Akeel A. Mohammed, Dr. and A. Jadoaa, Ameer}, title = {Experimental Study into Effect of Developing Section Length on The Heat Transfer Process in a Horizontal Annulus}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {62-72}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26608}, abstract = {ABSTRACT An experimental investigation has been presented to study the heat transfer process in thermally developed region of horizontal concentric annulus with an adiabatic inner tube and uniformly heated outer tube. Three lengths of entrance section have been used to achieve the hydrodynamically fully developed flow before test section with (L/Dh=50,75 and 100). The study has covered the range of Reynolds number (450≤ Re≤2000) and Richarson number (0.1≤ Ri≤ 0.7). Results show that the heat transfer process in the lower part of annulus is better than that in the upper part; and the vortex strength increases as Rayligh and Rynolds numbers increase. An empirical correlation for the average Nusselt number as a function of Rayliegh and Reynolds numbers and L/Dh has been deduced and compared with available literatures to give the same trend and behavior.}, keywords = {Key wards,Heat transfer,Annulus}, title_ar = {دراسة عميلة لتأثير طول مقطع التشكيل على عملية أنتقال الحرارة بتجويف حلقي أفقي}, abstract_ar = {الخلاصة:تم أجراء تجارب عملية لدراسة عملية أنتقال الحرارة بمنطقة التشكيل الحراري لتجويف حلقي متمركز بأنبوب داخلي معزول وانبوب خارجي مسخن تسخين منتظم.أستخدمت ثلاث اطوال لمقاطع الدخول للحصول على جريان تام التشكيل الهيدرديناميكي (L/Dh=50,75 and 100) .غطت الدراسة مدى رقم Re (450 ≤ Re ≤ 2000) ورقم Ri (0.1 ≤ Ri ≤ 0.7). بينت النتائج بأن عملية أنتقال الحرارة بالجزء السفلي للتجويف الحلقي أفضل من الجزء العلوي, ومقاومة الدوامة يزداد بزيادة رقم Ra ورقم Re. تم أستنباط معادلة تجريبية لمعدل رقم Nu كدالة لرقم Re ورقم Ra وقيمة(L/Dh)cal. لمقطع المخمد وقورنت مع الادبيات السابقة لتعطي نفس السلوك والمنحى.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26608.html}, eprint = {https://rengj.mosuljournals.com/article_26608_4c00c1d1f4feac987bc4b790c3604a36.pdf} } @article { author = {Ahmed Waheed Mustafa, Dr.}, title = {The Effect of Impinging Jet on the Flow and Heat Transfer from Isothermal Moving Plate}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {73-83}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26609}, abstract = {Abstract The effect of impinging uniform jet on flow and heat transfer over isothermal moving plate is investigated. The flow and temperature fields are studied numerically with different jet velocity ratio (jet to plate velocity ratio 0-5). The laminar flow field is analyzed numerically by solving the steady, two-dimensional incompressible Navier-Stokes and energy equations. A collocated (non-staggered) grid is used in the momentum equations, which discretized by finite volume method, SIMPLE algorithm is used to adjust the velocity field to satisfy the conservation of mass. The range of Reynolds number is (Re = 10 - 100). The results show that at high jet velocity ratio (V/U = 5) and Reynolds number (Re = 100), the rate of heat transfer from the plate is doubled.}, keywords = {KEYWORDS,Impinging Jet,Finite volume,Collocated Grid}, title_ar = {ثاتير النفث الاصطدامي على الجريان وانتقال الحرارة من صفيحة متحركة وبدرجة حرارة ثابتة}, abstract_ar = {ثاثير النفث الاصطدامي المنتظم على الجريان وانتقال الحرارة من صفيحة متحركة بدرجة الحرارة ثابتة تمت دراستة. حقل الجريان ودرجة الحرارة تم دراسته عدديا عند نسب سرع نفث مختلفة (نسبة سرعة النفث الى سرعة الصفيحة تتراوح من 0 الى 5). حقل الجريان الطباقي وحقل درجة الحرارة تم تحليليه عدديا بحل معادلات نافير ستوك المستقرة والثنائية الابعاد وكذلك معادلة الطاقة المستقرة والثنائة الابعاد. تم استحدام شبكة متحدة الموقع لتقطيع معادلات الزخم باستخدام طريقة الحجم المحدد. خوازمية (SIMPLE) استخدمت لتصحيح حقل السرع لتحقيق حفظ الكتلة. مدى رقم رينولد هو (10-100) . بينت النتائج انه عند نسبة سرعة نفث عالية (V/U =5) ورقم رينولد (Re =100) فأن معدل انتقال الحرارة من الصفيحة يتضاعف.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26609.html}, eprint = {https://rengj.mosuljournals.com/article_26609_a6e0ec77f9c753ef8f2d32e02ac170dd.pdf} } @article { author = {A. R. A. Habbo, Dr. and A. Khalil, Raad and S. Hammoodi, Hassan}, title = {Effect of Magnetizing the Fuel on the Performance of an S.I. Engine}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {84-90}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26611}, abstract = {Abstract The aim of this study is to investigate the effect of the magnetized fuel on the perfor-mance of spark ignition engine. The engine performance was observed by examining the engine brake power (BP) , thermal efficiency , specific fuel consumption (SFC) and exhaust emissions .The fuel is subjected to a magnetic field which is placed to fuel supply line to magnetize the fuel before admitted to the engine cylinder. Two types of magnetic coils were adopted in this study, the first one with 1000 Gauss and the second with 2000 Gauss. Experimental tests were conducted at a speed of 2000 rpm , compression ratio 8 , wide open throttle (WOT) and ignition timing was set between 50 and 300 BTDC . The results show a significant improvements in engine performance, the thermal efficiency and engine power increased by (4 %) and (3.3 %) respectively when a magnetic coil of 1000 Gauss is used, and a reduction in the specific fuel consumption by (12.8 %) was achieved. However, when the magnetic coil of 2000 Gauss is used the brake power is increased nearly by (16.4 %) , thermal efficiency showed an improvement nearly by (7.6 %) , while the specific fuel consumption is decreased by (21.3 %) with respect with no magnetic field case . The exhaust gas emissions show a reduction nearly by (80 %) of CO and by (44 %) of HC when the magnetic coil of 1000 Gauss is used. A further reduction nearly by (90 %) of CO and by (58 %) of HC is obtained when the magnetic coil of 2000 Gauss is used .}, keywords = {}, title_ar = {تأثير مغنطة الوقود في أداء محرك احتراق داخلي يعمل بالشرر}, abstract_ar = {المستخلص ان الهدف من هذه الدراسة هو ملاحظة تأثير الكازولين الممغنط على أداء محركات الاحتراق الداخلي التي تعمل بنظام شمعات القدح . تم اختبار أداء المحرك عن طريق قياس كل من القدرة الفر ملية ، الكفاءة الحرارية ، الاستهلاك النوعي للوقود و كمية الملوثات المنبعثة . تمت عملية مغنطة الوقود عن طريق ربط ملف مغناطيسي على خط تجهيز الوقود قبل دخوله الى اسطوانة المحرك . شملت الدراسة على استخدام نوعين من الملفات المغناطيسية الأول بشدة مجال مغناطيسي مقداره (1000 كاوس ) و الثاني بشدة (2000 كاوس ) . أجريت التجارب بنظام المبخرة عند فتحة كبيرة للخانق و بتغيير وقت بدء القدحة من 5 إلى 30 درجة قبل المنطقة الميتة العليا وبواقع زيادة مقداره 5 درجة في كل مرة . أظهرت النتائج على تحسين أداء المحرك بعد ربط الملف المغناطيسي حيث ازدادت الكفاءة الحرارية بمقدار 4 % و القدرة الفرملية بحدود 3.3 % عند استخدام الملف المغناطيسي (1000 كاوس ) مع نقصان بحدود 12.8 % في معدل استهلاك الوقود النوعي . أما عند استخدام الملف المغناطيسي ذو شدة (2000 كاوس ) فقد كانت الزيادة في القدرة الفرملية بحدود 16.4 % و الكفاءة الحرارية بحدود 7.6 % بينما كان النقصان في معدل استهلاك الوقود النوعي بحدود 21.3 % . أما بالنسبة للملوثات المنبعثة فقد أظهرت النتائج انخفاض انبعاث غاز اول اوكسيد الكاربون بحدود 80 % و الهيدروكاربونات 44 % عند استخدام الملف (1000 كاوس ) و انخفاض بحدود 90 % لغاز اول اوكسيد الكاربون و 58 % للهيدروكاربونات غير المحترقة عند استخدام الملف ( 2000 كاوس ) مقارنة بالنتائج التي تم الحصول عليها عند استخدام الكازولين دون تعريضه الى المجال المغناطيسي .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26611.html}, eprint = {https://rengj.mosuljournals.com/article_26611_796e6cb4541926ac08bf35034fabaa73.pdf} } @article { author = {O. F. S. Al-Damluji, Dr. and Th. Al-Saaty, Dr.A. Y. and Al-Nuaimi, Dr.R. M.}, title = {Nonlinear Coupled Finite Element Analysis of A Dam-Reserviour Under Dynamic Loading}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {91-111}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26613}, abstract = {ABSTRACT This research presents a nonlinear coupled analysis of a dam-reserviour problem with aspects of class I coupling for fluid-structure interaction and class II coupling for soil-pore fluid–structure interaction under earthquake excitations using finite element method. The analysis involves the compressibility of water, the flexibility of the dam, the earthquake excitation, the structural damping and the material nonlinearity on the response. An efficient computer program is developed for this analysis from the original computer code named as MIXDYN. The new software for analyzing the coupled behaviour is established using the pressure formulation for modelling of fluid and the u-p formulation for modelling of soil-pore fluid. Two differenent schemes for coupled field problems are implemented in the new computer code using the staggered partitioned solution technique in terms of sequential execution of single-field analyzers .Eight-nodded two-dimensional isoparametric element is adopted for idealization each of soil, fluid and structure. The Drucker Prager model is used to simulate the behavior of soil and concrete. Implicit-Implicit Newmark’s scheme with corrector predictor algorithm is employed for time integration of the equations of motion. The capability and the efficiency of the model are found to be very useful.}, keywords = {KEYWORDS,dam,reserviour,finite element method,Fluid,structure interaction,Soil,pore,fluid interaction,pressure formulation,p formulation}, title_ar = {التحلیل اللاخطی المزدوج لخزان سدتحت تأثیر حمل حرکی بطریقة العناصر المحدده}, abstract_ar = {الخلاصـةیقدم هذا البحث التحلیل اللاخطی لخزان سد ذی تداخل مزدوج من النوع الأول بین الماء والمنشأ والثانی بین التربة والماء والمنشأ تحت تأثیر الأحمال الدینامیکیة مثل الهزات الأرضیة بإستخدام طریقة العناصر المحددة. التحلیل شمل کلاً من إنضغاطیة الماء, مرونة السد, تأثیر الهزة ألأرضیة, إخماد المنشأ والخواص اللاخطیة للتربة والماء والمنشأ على سلوکیة السد. تم تطویر برنامح حاسبة المعروف (MIXDYN) وذلک باضافة إشتقاقات صیغة (p) لتمثیل ضغط الماء الحر فی المسائل ذات التداخل المزدوج بین الماء والمنشأ من النوع الأول وإشتقاقات صیغة (u-p) لحساب الإزاحات للدقائق الصلبة ومقدار ضغط المسام فی المسائل ذات التداخل المزدوج بین الماء والتربة من النوع الثانی. البرنامج إحتوى على أُسلوبین مختلفین لحل المسائل ذات التصرف المزدوج بشکل متعاقب إعتماداً على طریقة الحل المتعرج ((Staggered Solution Method. الأسلوب الأول : قادر على حل معادلات التوازن غیر الخطیة من الدرجة الثانیة الخاصة بالماء والمنشأ. أما الأسلوب الثانی فهو قادر على حل المعادلات التفاضلیة من الدرجة الأولى الخاصة بالتربة ومن الدرجة الثانیة الخاصة بالمنشأ. تم إعتماد العنصر المحدد الثنائی البعد ذو الثمانیة عقد فی تمثیل کل من التربة والماء والمنشأ. وتم إستعمال (Drucker Prager Model) لتمثیل سلوک کل من التربة والکونکریت. کما تم إعتماد طریقة نیومارک للتکامل الضمنی (Newmark Implicit-Implicit Scheme for Time Integration) وبأسلوب الحل المتعرج فی إجراء التکاملات على المعادلات الحرکیة. قورنت النتائج المستحُصلة مع النتائج المتوفرة وکان التوافق جیداً حیث أظهرت النتائج أهمیة وکفاءة المودیل وإمکانیة تطبیقه على مدیات أوسع فی مجالات التداخل المزدوج الأخرى.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26613.html}, eprint = {https://rengj.mosuljournals.com/article_26613_841f0daff305d567850aee43105462b4.pdf} } @article { author = {A. Mohammed, Abdalkader and Salim T. Yousif, Dr.}, title = {ANN Model for Predicting Ultimate Shear Strength of Reinforced Concrete Corbels}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {112-123}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26615}, abstract = {ABSTRACT The artificial neural network (ANN) model was developed using previous experimental data on Reinforced concrete (RC) corbels to simulate the behavior of RC corbels. The neural network model has six input parameters representing the concrete compressive strength ( ), shear span (a), effective depth (d), corbel width (b), area of main reinforcement (As), area of secondary reinforcement (Ah), one output parameter representing the ultimate shear load (Vu). A back propagation neural network (BPNN) with the log-sigmoid activation function is adopted due to its accuracy of prediction. The ANN model is constructed using the experimental data from the literature. The ANN predicted ultimate shear load which compared with those calculated by ACI318-08 code Formula and Russo model. The neural network model is to predict the shear load of RC corbel more accurate than the ACI318-08 code Formula, and Russo model. Through the parametric studies using the ANN model, the effects of various parameters such as ( , a, d, b, As, and Ah) on the behavior of RC corbel were shown. The results reveal that the proposed network model captures the RC corbel underlying shear behavior very well.}, keywords = {KEY WORD,Corbel,Reinforced concrete,Shear Strength}, title_ar = {نموذج الشبكات العصبية للتنبؤ بمقاومة القص القصوى للكتائف الخرسانية المسلحة}, abstract_ar = {الخلاصةطور نموذج الشبكة العصبية باستخدام نتائج عملية سابقة على الكتائف الخرسانية المسلحة لمحاكاة سلوكها. إن نموذج الشبكة العصبية المستخدم في هذه الدراسة يتكون من ستة معاملات مدخلة تمثل مقاومة انضغاط الخرسانة وفضاء القص والعمق المؤثر وعرض الكتف ومساحة التسليح الرئيسي ومساحة التسليح الثانوي و مخرج واحد يمثل حمل القص الأقصى. تم اعتماد الشبكة العصبية ذات الانتشار الخلفي مع دالة التفعيل من النوع (log-sigmoid) وذلك لدقتها في التنبؤ. انشأ نموذج الشبكات العصبية باستخدام النتائج العملية من الدراسات السابقة. إن حمل القص الناتج من الشبكة العصبية الاصطناعية قورن مع ذلك المحسوب من معادلة مدونة الخرسانة الامريكية ACI318-08 ومعادلة الباحث Russo . التنبؤ لنموذج الشبكات العصبية للحمل القص للكتائف الخرسانية اكثر دقة من معادلة مدونة الخرسانة الامريكية ACI318-08 ومعادلة الباحث Russo. من خلال استخدام نموذج الشبكات العصبية في الدراسة المقارنة، تأثير المعاملات المختلفة مثل( , a, d, b As, Ah ) على سلوك الكتائف الخرسانية المسلحة قد وضحت. النتائج بينت القدرة الجيدة لنموذج الشبكات العصبية للتنبؤ بسلوك القص للكتائف الخرسانية المسلحة.}, keywords_ar = {الكلمات الدالة,الكتائف,الخرسانة المسلحة,مقاومة القص}, url = {https://rengj.mosuljournals.com/article_26615.html}, eprint = {https://rengj.mosuljournals.com/article_26615_dccf59d410778f7ba25a925e4bd2b58c.pdf} } @article { author = {R. S. Al-Omary, Zainab and Jassim M. Abdul-Jabbar, Dr.}, title = {Design and FPGA Implementations of Four Orthogonal DWT Filter Banks Using Lattice Structures}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {124-137}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26616}, abstract = {Abstract In this paper, lattice structures for DWT are introduced through the design and FPGA implementations of the orthogonal Daubechies filter banks of orders 2, 4, 6 and 8. Multipliers and shift-add methods are both used to perform multiplication operations for these types of filter banks. Two implementation techniques are introduced, namely; the pipelining technique that is efficient from the throughput point of view, and the area efficient bit-serial implementation technique. The obtained results show the ability to achieve high throughput using pipelining (with 2 output samples / clock) on behalf of the area allocation. While bit-serial technique minimizes the allocated area on behalf of the throughput which may decrease with increasing filter order. As compared with other recent implementations, the results of implementing the designed filter banks using the SPARTAN-3E FPGA kit are efficient in minimizing implementation complexity to 0.584 - 0.712 of its corresponding values for different structures in recent hardware implementations. It is also obtained that the resulting structures can operate at high frequencies (up to 47.09 MHz).}, keywords = {KEYWORDS,DWT,Filter Banks,FPGA,Bit,serial,Pipelining}, title_ar = {FPGA التصميم والبناء باستخدام لأربعة أجراف مرشحات متعامدة للتحويل المويجي المقطع باستعمال الهياكل المتشابكة}, abstract_ar = {الخلاصة في هذا البحث تم تقديم الهيكل الشبكي للتحويل المويجي المقطع من خلال تصميم أربعة من أجراف المرشحات (Daubechies) المتعامدة ذات المرتبة 2 و4 و6 و8 وتنفيذها باستخدام (FPGA). وقد أجريت عملية الضرب في أجراف المرشحات عملياً باستخدام كل من الضرب المباشر وطريقة التزحيف والجمع, وللتقنيتين المقترحتين, حيث تم التصميم باستخدام تقنية خطوط الأنابيب (Pipelining) ذات الأنتاجية العالية وتقنية (Bit-serial) ذات الكفاءة العالية من ناحية المساحة المحجوزة للتصميم. وقد أظهرت النتائج الموضحة في البحث إمكانية الحصول على إنتاجية باستخدام خطوط الأنابيب تصل إلى إخراجين في النبضة الواحدة على حساب زيادة المساحة المحجوزة مقارنة بتقنية (Bit-serial) والتي تؤدي الى حجز أقل مساحة ممكنة لتنفيذ التصميم على حساب إنتاجية النظام والتى تنخفض بزيادة مرتبة المرشح. أظهرت نتائج بناء أجراف المرشحات المصممة باستخدام جهاز (SPARTAN-3E) كفاءة في تقليل تعقيد المعماريات التي تم بناؤها وامتلاكها لنسبة استغلالية للكيانات المادية المتاحة لها تصل الى 0.712 - 0.584من نسبتها في معماريات سابقة لطرائق بناء مشابهة كانت تناولت هياكل مختلفة استخدمت لتنفيذ ذات المرشحات. هذا بالإضافة الى الحصول على هياكل ناتجة تشتغل في ترددات عالية تصل الى 47.09 MHz.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26616.html}, eprint = {https://rengj.mosuljournals.com/article_26616_8a0ce026711fa267603763b013b88020.pdf} } @article { author = {Ahmed Maamoon Alkababji, Dr.}, title = { Best Wavelet Filter for a Wavelet Neural Fricatives Recognition System}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {19}, number = {6}, pages = {138-150}, year = {2011}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2011.26617}, abstract = {Abstract Direct recognition of phonemes in speaker independent speech recognition systems still cannot guarantee good enough recognition results. But grouping phonemes at first then trying to recognize the phoneme itself is a promising field. On the other hand wavelets are widely used in speech and speaker recognition systems, this is motivated by the ability of wavelet coefficients to capture important time and frequency features. In this work the effect of the wavelet filter type on the efficiency of a phoneme recognition system is investigated (specifically fricatives). The Probabilistic neural network was used as a pattern matching stage for its well known and power full ability in solving classification problems. It was found that the Daubechies wavelet family (generally from db15 to db23) is a good candidate for a fricatives phoneme recognition system that is based on wavelets as a feature extraction stage.}, keywords = {KEYWORDS,Fricatives,Wavelet,Probabilistic neural network}, title_ar = {مرشح التحويل المويجي الأفضل لنظام تمييز المقاطع الصوتية الاحتكاكية باعتماد التحويل المويجي والشبكات العصبية}, abstract_ar = {الملخصالتمييز المباشر للمقطع الصوتي في أنظمة تمييز الكلام غير المعتمدة على الشخص لا تستطيع ضمان نسبة تمييز جيدة. لكن تقسيم المقاطع الصوتية إلى مجاميع (حسب النوع) ثم التمييز ضمن المجموعة كمرحلة لاحقة هو من المجالات الواعدة. من جهة أخرى فان التحويل المويجي له استخدامات واسعة في أنظمة تمييز المتكلم أو الكلام هذا بسبب قدرته العالية على استخلاص خصائص للزمن والتردد. في العمل الحالي تم دراسة تأثير نوع المرشح المويجي على أداء نظام تمييز للمقاطع الصوتية (الاحتكاكية بشكل خاص). تم استخدام الشبكة العصبية الاحتمالية كمرحلة مطابقة للهياكل وذلك لقدرتها العالية في حل مشاكل التصنيف .أظهرت النتائج أن المرشح من نوع دوبيجي (تحديدا من 15 إلى 23) هو من أفضل المرشحات للاستخدام في مرحلة استخلاص الخواص في أنظمة تمييز المقاطع الصوتية المبنية باستخدام التحويل المويجي.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_26617.html}, eprint = {https://rengj.mosuljournals.com/article_26617_0985ceb68bd5e44a85643628c4a2ff32.pdf} }