@article { author = {B. Abdurrahman, R. and A. Mohammed, Z. and A. H. Ahmed, Dr.}, title = {Effect of High Temperature on Engineering Properties of Light Weight Blocks Concrete}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {1-9}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.35165}, abstract = {Abstract Light weight concrete blocks have an important role in the last years for it is practical and economical benefit in the building construction. An It has light density providing high thermal insulation and less dead load normally all light weight concrete has fire resistance in its nature, as well as, these type of light weight block has the ability to support quite large amount of load and relatively easy to work and can be cut and shaped with hand tools. The effect of high temperature on light weight concrete blocks was studied after exposure to (150,350,550)ºC for one hour. The effect of the method of cooling after heating (by air or water) on the compressive and flexural strengths were studied and compared together. The water absorption capacity was also measured during the process of water cooling. The compressive strength relatively increased with high temperature and air cooling , and also increased with measuring the exposed time up to (90) minute, above this time the compressive strength decreased. For water cooling the compressive strength trend to decrease . Flexural strength is decreased as the exposed temperature increased in all cases. Key words: Concrete ,Light Weight Concrete, High Temperature.}, keywords = {Key Words,Light weight concrete,High Temperature}, title_ar = {تأثير درجات الحرارة العالية على الخصائص الهندسـية للكتل الخرسـانية الخفيفة الوزن}, abstract_ar = {الخلاصة إن المنافع الاقتصادية والعملية المتوفرة في الكتل الخرسانية الخفيفة جعلتها تحتل في السنوات الأخيرة مكانة هامة في بناء المنشآت والإقبال على تنفيذها في ازدياد مستمر، حيث أن الكثافة القليلة للمادة تفيد في تأمين عزل حراري عالي للمباني مع أحمال ميتة اقل، وبشكل تقريبي فان كافة أنواع الكتل الخرسانية الخفيفة تكون مقاومة للحرائق بطبيعتها، إضافة إلى أنها تتحمل أحمال عالية ويمكن قطعها بسهولة ودق المسامير بها والتعامل معها بأدوات نجارة عادية. تناولت هذه الدراسة تأثير درجات الحرارة العالية على الكتل الخرسانية الخفيفة المهواة (الثرمستون) من خلال تعريضها لمديات حرارية تضمنت oC(550،350،150) لمدة ساعة واحدة كما تم دراسة وتأثير طرق التبريد المتبعة بعد التسخين (تبريد بالهواء، تبريد بالماء) على مقاومة الانضغاط والانحناء لهذه الكتل كما تم قياس تأثير درجات الحرارة العالية على قابلية الامتصاص للماء أثناء تبريد العينة، أظهرت نتائج الدراسة إن مقاومة انضغاط الثرمستون تزداد ازدياد طفيفا بعد تسخينها وتبريدها بالهواء كما تزداد بازدياد وقت التعرض للحرارة بحدود ساعة ونصف ثم تبدأ بالانخفاض بعد زيادة هذه المدة كما تنخفض مقاومة الانضغاط عند تبريد العينات بالماء، وبالنسبة لمقاومة الانحناء كان تأثير الحرارة فيها سلبيا لكل الحالات. الكلمات الدالة: الخرسانة ،الكتل الخرسانية الخفيفة الوزن، الحرارة العالية}, keywords_ar = {الكلمات الدالة,الكتل الخرسانية الخفيفة الوزن,الحرارة العالية}, url = {https://rengj.mosuljournals.com/article_35165.html}, eprint = {https://rengj.mosuljournals.com/article_35165_f7501fa845e50ddbe7b5d7c00ca7e3a5.pdf} } @article { author = {Mohamad N. Mahmood, Dr. and Behnam, Ayad B.}, title = {EMBEDDED FORMULATION OF PRESTRESSED TENDON IN 3D – BRICK ELEMENT}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {1-14}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34783}, abstract = {Abstract In the present work a formulation of the reinforced bars and prestressed tendons embedded in the brick element is developed and used for the nonlinear analysis of reinforced-prestressed concrete beams. The reinforcement and prestressing bars are represented by an axial 3 nodded bar elements embedded into the 20 nodded isoparametric brick concrete element. Perfect bond is assumed between concrete and prestressing steel bars (or tendons) such that displacements and strains of the bars are assumed to be compatible with those of the concrete element. To verify the applicability of the model two prestressed beams are analyzed and the numerical results show a good agreement with the experimental one. Keywords: Brick element, Embedded bar, Finite element, Nonlinear analysis, Prestressed concrete.}, keywords = {KEYWORDS,Embedded bar,finite element,Nonlinear analysis,Prestressed concrete}, title_ar = {صیاغة الاسلاک المجدولة المسبقة الجهد المطمورة فی العنصر الطابوقی ثلاثــی الابعاد}, abstract_ar = {الخلاصة یتضمن البحث الحالی وضع صیاغة للأسلاک المجدولة المسبقة الجهد وقضبان حدید التسلیح المطمورة فی العنصر الطابوقی لغرض استخدامها فی التحلیل غیر الخطی للعتبات الخرسانیة المسلحة المسبقة الجهد. تم تمثیل وصیاغة قضبان التسلیح والمسبقة الجهد کعناصر محوریة ثلاثیة العقد مطمورة فی العنصر الطابوقی الخرسانی الموحد المعلمیة ذات 20 عقدة. اعتمد فی الصیاغة على فرضیة الترابط التام بین القضبان والخرسانة بافتراض حالة التوافق فی الإزاحات والانفعال بین القضبان والخرسانة. لإثبات صحة وقابلیة النموذج تم تحلیل عتبتین مسبقتی الجهد وأظهرت نتائج التحلیل توافقاً جیداً مع النتائج العملیة.Introduction:}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34783.html}, eprint = {https://rengj.mosuljournals.com/article_34783_38da7fd4f76211bbea1d4526dac9f436.pdf} } @article { author = {Mohamed Daood, Daad and Salim Esmaeil, Dr.Nadia}, title = {Processing Lightweight Aggregate to produce Lightweight Concrete}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {10-23}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.35172}, abstract = {Abstract The modern techniques development used in the production of concrete led to the emergence of types of concrete with different densities compared to normal concrete . This research aimed manufacturing types of lightweight aggregate (coarse and fine) and then the production of lightweight concrete blocks with a good thermal insulation , by using available locally materials . Two types of lightweight aggregate , have been produced by using two methods of manufacturing , first type , where AL-Hadbaa aggregate , produced from Clay , which is on the edge of the Tigris river in Mosul , using 50% Clay and 50% silt , the density obtained about 860 Kg/m3 . The second AL-Rabean aggregate , was the adoption of natural laminated Clay which is located in Nineveh province , in very large quantities , it's mineralization is Montmurlite and kaolinite , density obtained was 750 Kg/m3 , this type did not produce in Iraq and which it's manufactured method simple and economic . The standard tests have been made and were adopted in the production of concrete blocks , lightweight concrete block produced from AL-Hadbaa aggregate , used in bearing walls , have 28 – day compressive strength 15.33 N/mm2 and density about 1770 Kg/m3 . The AL-Rabeaan aggregate used to product concrete block for the purposes of thermal insulation , it's thermal conductivity coefficient was 0.55 W/m.kcal and have a density 1640 Kg/m3 . Keywords : Clay , lightweight aggregate , concrete block}, keywords = {KEYWORDS,lightweight aggregate,concrete block}, title_ar = {تصنيع ركام خفيف الوزن لإنتاج خرسانة خفيفة عازلة}, abstract_ar = {الخلاصةأدى التطور الحديث للتقانات المستخدمة في إنتاج الخرسانة إلى ظهور أنواع من الخرسانة ذات كثافات مختلفة مقارنة بالخرسانة الاعتيادية . وهذه الكثافة يمكن الحصول عليها بعدة طرق ، إحدى هذه الطرق استعمال الركام الخفيف الوزن Lightweight aggregates. يهدف البحث الحالي إلى تصنيع أنواع من الركام الخفيف ( الخشن والناعم ) ومن ثم إنتاج كتل خرسانية خفيفة ذات عزل حراري جيد من مواد متوفرة محليا وبكلفة اقتصادية مناسبة . وقد تم الحصول على نوعين من الركام الخفيف باستخدام طريقتين من التصنيع، أطلق على النوع الأول ركام الحدباء تم تصنيعه من طين طفل موجود على حافات دجلة في منطقة الموصل بنسبة 50% وغرين Silt بنسبة 50% وتم الحصول على ركام بكثافة 860 كغم/م3. وأطلق على الثاني ركام الربيعين، وتم اعتماد الطين الطبيعي الصفائحي الموجود في محافظة نينوى بكميات كبيرة جداً والذي معدنه هو المونتمورلونايت والكاؤلين وتم الحصول على ركام بكثافة 750كغم/م3 ولم يصنع هذا النوع سابقاً في العراق وطريقة تصنيعه بسيطة واقتصادية. لقد أجريت الفحوصات القياسية لهما وتم اعتمادهما في إنتاج الكتل الخرسانية فقد حصلنا على كتل خرسانية خفيفة تستعمل في الجدران الحاملة من ركام الحدباء وكانت قوة تحملها للضغط بعمر 28 يوم 15.33 نيوتن/ملم2 وكثافتها 1770 كغم/م3 أما ركام الربيعين فقد استخدم في إنتاج كتل خرسانية لأغراض العزل الحراري وقد كان معامل التوصيل الحراري K له 0.55 واط/م.كليو سعرة وبكثافة 1640 كغم/م3 . الكلمات الدالة : الطين ، الركام الخفيف الوزن ، الكتل الخرسانية .}, keywords_ar = {الكلمات الدالة,الركام الخفيف الوزن,الكتل الخرسانية}, url = {https://rengj.mosuljournals.com/article_35172.html}, eprint = {https://rengj.mosuljournals.com/article_35172_68c973e598a73bc52c518c1e380c8982.pdf} } @article { author = {Najem, Rabi M.}, title = {OPTIMUM COST DESIGN OF R. C. ONE WAY SLABS}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {15-27}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34788}, abstract = {Abstract In this research , the formulation of optimum cost design for one way reinforced concrete slabs is presented , since it is useful and have a widespread usage among practicing engineering and applied to realistic structures subjected to the actual constraints of commonly used design codes such as the American concrete instituted code (ACI,2005). The formulation contains minimizing an objective function that represent the cost of steel reinforcement and the cost of concrete , which is subjected to many constraints containing : flexural constraints , serviceability constraints and deflection constraints that illustrated with details in this paper . the optimum solution is calculated using the lagrangian multipliers method , and a visual basic computer software were developed to find the optimum solution . Key Words: Optimization , Lagrangian Multiplayer , Optimum Cost Design . One way Slabs .}, keywords = {Key Words,Lagrangian Multiplayer,Optimum Cost Design,One way Slabs}, title_ar = {التصمیم الامثل للکلفة للبلاطات المسلحة أحادیة الاتجاه}, abstract_ar = {الخلاصةفی هذا البحث تم استنباط صیغة لایجاد التصمیم الامثل من ناحیة الکلفة للبلاطات المسلحة احادیة الاتجاه نظراً لفائدتها وأستخدامها الواسع فی مجال الهندسة المدنیة التطبیقیة وأمکانیة تطبیقها على منشأت واقعیة خاضعة لأحمال ومحددات تصمیمیة من المدونات المعتمدة فی التصمیم للهندسة المدنیة کمدونة الـ ACI , 2005 .تتمثل صیاغة هذه الطریقة بتطبیق الامثلیة على دالة الهدف التی تمثل کلفة حدید التسلیح وکلفة الخرسانة ، والتی تکون خاضعة لمحددات تصمیمیة مثل : محددات الانحناء ، مححدات الدیمومة ومحددات الهبوط والموضحة بالتفصیل فی هذا البحث . تم أستخدام طریقة لاکرانج لحساب الحل الامثل .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34788.html}, eprint = {https://rengj.mosuljournals.com/article_34788_672b0b045f9bc33d26be868f99ed2dfe.pdf} } @article { author = {Al Zubaydi, A.H. and T. Al- Layla Professor, M.}, title = {Behavior of Lime Stabilized Gypseous Soil Beams Under static Loads}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {24-39}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.35180}, abstract = {Abstract This work aims to study the stress-strain curves of soil samples subjected to tensile stress. The samples (50*50*300 mm) were prepared from lime stabilized gypseous soil using (3%) lime as stabilization percent. The samples were cured at (25,49 and 600C) for a period of (2,15,30,90 and 180) days. The results obtained from flexural tensile tests were analyzed using three methods of analysis. These methods are, the elastic bending theory, direct, and differential method. The elastic and the direct methods gave, generally similar results of the soil flexural tensile stress while the differential method gave lower values. Also the tensile stress-strain curves obtained by the elastic method were consistent, while the curves from direct and differential methods are in consistent, with the exception of the samples compacted at the dry side of the compaction curve.}, keywords = {}, title_ar = {سلوکیة عتبات التربة الجبسیة المثبتة بالنورة تحت تأثیر الأحمال الساکنة}, abstract_ar = {الخلاصةیهدف هذا البحث إلى دراسة منحنیات الإجهاد-الانفعال, لتربة جبسیة تعرضت إلى اجهادات شد. حیث تم معاملة التربة بنسبة (3%) نورة وهی النسبة المفضلة ثم حضرت نماذج بأبعاد (50 mm× 50×300) وبطریقة الرص المعدلة وبمحتوى رطوبی یمثل الجانب الجاف و الأمثل ثم الرطب من منحنی الرص. بعدها تم إنضاج النماذج بدرجة الحرارة (60, 49, 250 C) ولفترة (180,90,30,15,2) یوم. جرى تحلیل النتائج التی تم الحصول علیها من فحص الانثناء وباستعمال ثلاث طرائق للتحلیل, هی الطریقة المرنة, الطریقة المباشرة, والطریقة التفاضلیة. کانت نتائج مقاومة الشد وحسب الطریقة المرنة والطریقة المباشرة وبصورة عامة متقاربة. فی حین کانت مقاومة الشد المحسوبة بالطریقة التفاضلیة أقل من الطریقتین السابقتین. کذلک کانت منحنیات الإجهاد-الانفعال التی تم الحصول علیها من الطریقة المرنة منتظمة, فی حین کانت المنحنیات غیر منتظمة عند حسابها بالطریقة المباشرة والطریقة التفاضلیة, ماعدا منحنیات النماذج التی تم رصها عند المحتوى الرطوبی الذی یمثل الجانب الجاف من منحنی الرص فقد کانت منتظمة.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_35180.html}, eprint = {https://rengj.mosuljournals.com/article_35180_accce5138b5b066fd01bd205e1143134.pdf} } @article { author = {Salim T.Yousif, Dr. and A. AL- Jurmaa, Majid and A. AL- Jurmaa, Majid}, title = {Modeling of ultimate load for R.C. beams strengthened with Carbon FRP using artificial neural networks}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {28-41}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34813}, abstract = {Abstract The use of carbon fiber reinforced composite materials is an accepted technology that is being used in practice to strengthen existing reinforced concrete (R/C) elements. An artificial neural network (ANN) model was developed using past experimental data on flexural failure of R/C beams strengthened by carbon FRP. The input parameters cover the carbon sheet properties, beam geometrical properties and reinforcement properties; the corresponding output is the ultimate load capacity. The ANN prediction and the measured experimental values are compared with load prediction of ACI440.2R-02 formulas. A sensitivity study of parameters that affect ultimate load of R/C beams strengthened by carbon FRP is carried out. It is concluded that ANN can predict, to a good degree of accuracy, the ultimate load capacity of R/C beams strengthened by carbon FRP and it is a viable tool to carry out parametric study of flexural behavior of R/C beams strengthened by carbon FRP. Keywords: carbon FRP, Reinforced Concrete Beam, Ultimate Load, and Neural Network}, keywords = {KEYWORDS,Reinforced Concrete Beam,Ultimate Load,and Neural Network}, title_ar = {نمذجة الحمل الأقصى للعتبات الخرسانية المسلحة و المقواة بألواح الكربون باستخدام الشبكة العصبية الاصطناعية}, abstract_ar = {تستخدام الواح الكاربون عمليا كتقنية جيدة لتقوية الاعتاب الخرسانية المسلحة ، تم تطوير نموذج شبكة عصبية اصطناعية باستخدام بيانات مختبرية سابقة ذات فشل انحناء، لاعتاب خرسانية مسلحة مقواة بالواح الكاربون، شملت البيانات الداخلة خواص الواح الكاربون ، ابعاد العتب الخرساني ، خواص التسليح وكانت النتائج الخارجة متمثلة بقابلية التحمل القصوى .تم مقارنة النتائج المستحصلة من نموذج الشبكة العصبية الاصطناعية بالنتائج المختبرية ( العملية) كما تم مقارنتها مع النتائج المستحصلة من معادلات مدونة الخرسانة الامريكية وتبين كفائة الشبكة العصبية بدقة عالية ، كما تم اجراء دراسة مقارنة للتحمل الاقصى للعتبات الخرسانية المسلحة المقواة بالواح الكاربون.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34813.html}, eprint = {https://rengj.mosuljournals.com/article_34813_df75276f1a6b74954151a4b0166e5875.pdf} } @article { author = {Kamel A. Al-Mohseen, Dr.}, title = {Frequency Analysis of Hydrologic Drought (Case Study)}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {40-52}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.35187}, abstract = {ABSTRACT In this paper, the possibility of studying the occurrence probabilities of hydrologic drought events has been explored. The obtained results were based on the case study of the annual inflow to Fatha discharge station on Tigris river, Iraq, over the period (1931-1988). This recorded time series is basically used to evaluate the observed duration and severity of the drought. The theory of runs is adopted to estimate, both, the probabilities of duration and severity of the drought. Three stochastic models have been used for modeling the hydrologic process having short-term time dependence to generate additional data for statistical inferring of the drought duration. Models such as(AR(1),AR(2),and ARMA(1,1))have been formulated by means of modern techniques called (SAMA-2007). The number of the generated series was ranging between 100 to 10000 series. This help in the estimation of the probabilities of drought severity for which no rigorous mathematical solution is exist yet. Discrepancy in the performances of the proposed models have been noticed, especially in their capabilities of preserving the statistical properties of the observed time series. It is concluded that while a certain model has a satisfactory performance in preserving certain parameters, it failed in the estimation of other parameters. (Keywords: Drought, Stochastic Modeli}, keywords = {KEYWORDS,Stochastic Modeli}, title_ar = {تحليل تردد الجفاف الهيدرولوجي (دراسة حالة}, abstract_ar = {المستخلصخلص البحث الحالي إلى إمكانية دراسة وتحليل احتماليات تردد فعالية الجفاف (فترةً وقسوةً). إن نتائج البحث مبنية بشكل أساسي على دراسة حالة الجريان السنوي في محطة قياس تصريف الفتحة الواقعة على نهر دجلة (العراق)، للفترة (1988-1931). استخدمت سلسلة الجريان المسجلة كأساس لتقييم فترة وقسوة الجفاف الهيدرولوجي المرصودة.لقد تم اعتماد نظرية الحدث المستمر (Theory of Runs) لإيجاد احتماليات حدوث فترات جفاف حرجة وبقسوة معينة. كما واستخدمت هذه السلسلة لغرض استحداث ثلاثة نماذج تصادفيه هي:( (ARMA(1,1),AR(2),AR(1) وذلك بالاستفادة من التقنية الجديدة (SAMS-2007)لتوليد بيانات إضافية (لتعزيز التعويل عليها إحصائيا) في استقراء فترة الجفاف خاصة وان أعداد السلاسل المولدة قد تراوح بين 10000-100 سلسلة. لقد ساهمت هذه النماذج في تسهيل عملية تخمين احتمالية قسوة الجفاف التي يصعب اشتقاقها رياضياً. تفاوت أداء النماذج المستخدمة في إمكانية محافظتها على الخواص الإحصائية للسلسلة الزمنية المرصودة، ففي الوقت الذي اظهر احدها قدراً من المحافظة على بعض المعالم المرصودة، اخفق في تخمين معالم أخرى.استنتج البحث بأن اعتماد النموذج المناسب يجب ان لايكون مبنياً على مدى تقارب المعالم الإحصائية المخمنة مع تلك المرصودة فقط، وانما يتوجب الاستدلال عليه من خلال إمكاناته في تخمين بعض المعطيات الأخرى كعدد فترات الجفاف وحجم الخزين.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_35187.html}, eprint = {https://rengj.mosuljournals.com/article_35187_0f77879e41e0f1641902ee05597eb4a3.pdf} } @article { author = {Abdul Khalik Al-Taei, Dr.}, title = {Gap Acceptance, and Traffic Safety Analysis On U-Turn Median OpeningsOf Arterial Roads}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {42-53}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34824}, abstract = {ABSTRACT In this study, eight locations on U-turn median openings in Duhok City were investigated about gaps or lags of traffic opposing and delaying traffic turning left. Other data was collected from the scene like conflicts with turning traffic, travel speed, and volumes of opposing and parallel flow. Accident frequency experienced near U-turn openings location for three years (2005-2007) was collected too. Analysis of data using statistical methods show different empirical models correlating independent variables like , gap length travel speed , traffic volume , approach width , conflict rate…etc. with dependent variables like , delay time , accident rate , and percentage of drivers accepting or rejecting gaps . Average lag obtained to control safety of studied locations was 3.5 sec. Key Word: Gap Acceptance, Duhok}, keywords = {Key Word,Duhok}, title_ar = {تحليل قبول الثغرات والسلامة المرورية في مواقع الاستدارة في فتحات الجزرات الوسطية للطرق الشريانية}, abstract_ar = {الخلاصةفي هذه الدراسة تم تحديد وجمع البيانات من ثمانية مواقع في فتحات الجزرات الوسطية في مدينة دهوك مثل التداخلات المرورية للمركبات المستديرة ، سرعة المرور المعاكس ، الحجوم المرورية الموازية والمعاكسة كما تم جمع ترددات الحوادث المرورية الحاصلة خلال ثلاثة سنوات (2005-2007) بالقرب من مواقع الدراسة تم جمعها كذلك.تم تحليل البيانات بالطرق الإحصائية وتم الحصول على مجموعة من الموديلات الرياضية الافتراضية ذات العلاقة التي تربط المتغيرات غير المعتمدة مثل طول الثغرات المرورية ، سرعة المركبات ، كمية الجريان المروري ، عرض الطريق الشرياني ، ومعدلات الإعاقة المرورية...الخ ، أما المتغيرات الحرة مثل زمن التأخير للمرور المستدير من فتحات الجزرات الوسطية ، معدلات الحوادث المرورية الحقيقية ونسبة السواق الذين يقبلون هذه الثغرات المرورية وينفذون الاستدارة ونسبة السواق الرافضين لها أي المنتظرين لثغرة مناسبة. من خلال التحليل تم الحصول على معدل قيمة الثغرة الواحدة في كافة المواقع المشمولة بالدراسة وقدرها 3.5 ثانية والتي تحقق متطلبات السلامة المرورية.الكلمة المفتاحية: دهوك ، قبول الثغرات}, keywords_ar = {الكلمة المفتاحية,قبول الثغرات}, url = {https://rengj.mosuljournals.com/article_34824.html}, eprint = {https://rengj.mosuljournals.com/article_34824_cf0cdef264a635771eedd3e28edeaec9.pdf} } @article { author = {Hazim Sheet, Dr.Eman}, title = {OPTIMAL IRRIGATION PROGRAMMING}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {53-60}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.35198}, abstract = {A mathematical optimization model for optimum weekly irrigation water requirements for maize crop at Mosul area is developed. The main objective function is to maximize profit. The growing season is divided into (17)weeks with constraints on actual evapotranspiration, soil moisture at the root zone and deep percolation. The total amount of irrigation water requirements is assumed known and limited at the beginning of the season. The results of this approach was compared with a previous simulation model for irrigation water requirement. It is found that optimization model reduce seasonal irrigation water by 13% compared with simulation models. The proposed model is simple for predicting weekly irrigation requirements and can be used for any crop by changing crop data. where simulation models take longer time and do not give optimal solutions. As this model is applied to many crops grown over large areas, a huge amount of irrigation water may be saved KEYWORDS:optimization ,irrigation scheduling, optimal yield}, keywords = {KEYWORDS,irrigation scheduling,optimal yield}, title_ar = {برمجة الارواء المثلى}, abstract_ar = {الخلاصةتم وضع أنموذج أمثلية رياضي لإيجاد احتياجات الري الأسبوعية المثلى لمحصول الذرة بدالة هدف زيادة العائدات حيث تم تقسيم موسم النمو إلى (17) أسبوع مع وضع محددات على الرطوبة في الخزان الجذري والتبخر-نتح الحقيقي والتخلل العميق بحيث تكون مجموع مياه الريات مساوية لكمية محددة من المياه متوفرة في بداية الموسم ، وتمت مقارنة النتائج مع أنموذج محاكاة معد مسبقا لإيجاد احتياجات الري . وقد تبين أن استخدام أنموذج الامثلية يقلل كميات مياه الري الموسمية للمحصول بنسبة 13% عنه عند استخدام أنموذج المحاكاة. يعد الأنموذج وسيلة سهلة ومناسبة لإيجاد احتياجات الري الأسبوعية ويمكن تطبيقه لأي محصول آخر بتغيير معلومات المحصول مقارنة مع استخدام نماذج المحاكاة حيث تأخذ وقتا أكثر ولا تعطي الكميات المثلى كما توفر كمياة كبيرة من المياه عند تطبيق الأنموذج لعدة محاصيل ولمساحات كبيرة.}, keywords_ar = {الكلمات الدالة,جدولة الارواء,الإنتاجية المثلى}, url = {https://rengj.mosuljournals.com/article_35198.html}, eprint = {https://rengj.mosuljournals.com/article_35198_2dd2457d66f642e7451d345f0162ed74.pdf} } @article { author = {A. Al-Tayyar, H. and A. Mawjoud, S.}, title = {Handoff Priority Schemes in Wireless Mobile Cellular System}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {54-60}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34852}, abstract = {Abstract Handoff operation, algorithm and modeling is vital in wireless cellular system. Two fundamental handoff procedures exist. The first model concerning the propagation environment and the second model is the limited channel resources which is dealt with in this paper. A realistic model of guard channel priority representing mobility is suggested and simulated. Keywords: Wireless network, Handoff priority schemes.}, keywords = {KEYWORDS,Handoff priority schemes}, title_ar = {أولويات طرق المناقلة لنظام لاسلكي خلوي متنقل}, abstract_ar = {المستخلصإن خوارزمية ونمذجة عملية المناقلة هي من الأولويات لنظم الاتصالات اللاسلكية. هنالك طريقتان أساسيتان للمناقلة. النموذج الأول يخص ظروف الانتشار والنموذج الثاني هو مصادر القنوات المحدودة والنموذج الثاني الذي تم التعامل معه في هذا البحث وتم اقتراح نموذج واقعي يتضمن مصادر القنوات المحددة والذي يمثل حالة الحركة الواقعية في الخلايا ومن ثم محاكاة هذا النموذج ودراسة خواصه.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34852.html}, eprint = {https://rengj.mosuljournals.com/article_34852_f1fa3b6d070277cabef9d7d591f35675.pdf} } @article { author = {A. Mohammed, Khalis}, title = {Mole Fraction Effect on Semiconductor Optical Amplifier Specifications}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {61-69}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34862}, abstract = {Abstract Semiconductor optical amplifier had been studied theoretically using the traveling wave equation. The study took into consideration the many parameters that could affect the operation of amplifier, such as mole fraction, noise figure and material gain have been studied theoretically for the suggested amplifier in the wavelength of 1.55 m. The results show that gain material peak was shifted when injected current and wavelength were varied. An interesting result of the noise figure was found to be minimum at the operating wavelength of 1.55 m. Keywords: Amplifier noise, noise, noise figure, noise measurement, wideband semiconductor optical amplifiers.}, keywords = {KEYWORDS,Noise,noise figure,noise measurement,wideband semiconductor optical amplifiers}, title_ar = {تأثير الكسر المولي على مواصفات مكبر شبه الموصل الضوئي}, abstract_ar = {الملخصتم في هذا البحث استخدام معادلةَ الموجة المتنقلة لمكبرشبه الموصل الضوئي نظرياً.هذه الدراسة أَخذت بنظر الإعتبار العديد من المتغيرات التي يمكن أَن تكون مؤثرة على عمل المكبر. حيث درس كل من الكسر المولي و شكل الضوضاء و الكسب الماديِ نظرياً للمكبر المقترحِ ولطول موجي (1.55m). بينت النتائج أن قمة الكسب المادي ازيحت مكانياً بتغيير كل من تيارالحقن والطول الموجي. نتائج مثيرة تم الحصول عليها لشكل الضوضاء عند قيمتها الدنيا و لطول عمل موجي (1.55 m).}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34862.html}, eprint = {https://rengj.mosuljournals.com/article_34862_ea8db01f0963b498589bf8ec989b24de.pdf} } @article { author = {A. Alfakhry, Ahmed and Turki Hassan Ali, Dr. and Attallah, Faris}, title = {The Efficiency of the Spatial Distribution of Civil Defense Stations in Mosul City}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {61-104}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.35204}, abstract = {Abstract Civil defense stations in cities are one of the basic emergency services that should be considered in mind of every urban designers and planners who is going to design and develop any city , because of the urgent need to provide safety requirements against fire The construction and building activities in Mosul city had witnessed a great expansion with high rate increase in number of its population in the last decades, this increase in population growth had not accompanied by provision of the essential services needed by the city because of the known circumstances that prevailed in Iraq and its cities during the past period. This led to increase pressure on the service activities in the city and worsening the outcome of such infrastructure services, from those the firefighting and rescue services. So the fulfillment of civil defense stations provision and its distribution requirements has become one of the necessities that the designers should be addressed and solved. This research, study the efficiency of spatial distribution of civil defense stations in Mosul city, its number, and positioning according to the actual need, based on the available local and international standards.}, keywords = {}, title_ar = {كفاءة التوزيع المكاني لمراكز الدفاع المدني في مدينة الموصل}, abstract_ar = {المستخلصتعد مراكز الدفاع المدني في المدن إحدى فعاليات الطوارئ الأساسية التي يأخذها المصمم والمخطط الحضري بنظر الاعتبار عند تصميم البنية العمرانية أو تطوير أي مدينة, بسبب الحاجة الماسة لتوفير متطلبات الأمان والسلامة ضد الحرائق.بالرغم من اتساع مساحة نشاط التشييد والعمران في مدينة الموصل وارتفاع عدد سكانها بمعدلات عالية في العقود الأخيرة فان هذه الزيادة في معدلات النمو السكاني لم يصاحبها توفير للخدمات الأساسية التي تحتاجها المدينة بسبب الظروف المعروفة التي عاشها العراق ومدنه خلال الفترة المنصرمة مما أدى إلى زيادة الضغط على الأنشطة الخدمية في المدينة الأمر الذي أدى بالنتيجة إلى تردي تلك البنية الخدمية ومن تلك الأنشطة خدمات الطوارئ وخاصة ما يتعلق منها بمكافحة الحرائق والإنقاذ, فقد أصبح الإيفاء بمتطلبات توفير مراكز إطفاء وطريقة توزيعها من الضرورات التي يجب على المخطط والمصمم مواجهتها وحلها.هذا البحث يتناول دراسة كفاءة توزيع مراكز الإطفاء في مدينة الموصل وأسلوب توقيعها وعددها قياسا للحاجة الفعلية للمدينة وذلك استنادا إلى المعايير المحلية والعالمية المتوفرة.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_35204.html}, eprint = {https://rengj.mosuljournals.com/article_35204_1ac865fd0b26fc901e2112165271323c.pdf} } @article { author = {Taher Qassim, Yahya and Dhafir A. Alneema, Dr.}, title = {FPGA Based Implementation of Convolutional Encoder- Viterbi Decoder Using Multiple Booting Technique}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {70-80}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34888}, abstract = {Abstract Convolutional encoding is considered one of the forward error correction schemes. It is an essential component of wireless communication systems such as the third generation (3G) mobile systems, which utilize some formulation of Convolutional encoding usually decoded via Viterbi decoders. There are different structures of Convolutional encoding which impart different requirements on the decoder. The Viterbi decoder segments with slight modifications can be used on systems with different constraint lengths, frame size and code rates. In this research, the design and implementation of Convolutional encoder with constraint length 3 and rate 1/2, and Viterbi decoder on Spartan 3E FPGA Starter kit (supported with XC3S500E) using multiple booting technique has been presented. VHDL language is used as a design entry. In the starter kit mentioned above, two designs are implemented on the flash memory using the multiple booting technique: the Convolutional encoder and the Viterbi decoder. The FPGA is configured with the specified design depending on the loaded program from the Intel flash memory. With this way of configuration, the FPGA itself can operate as a Convolutional encoder or Viterbi decoder that gain benefit through the reuse of the same hardware. Key words : Convolutional encoder, Viterbi decoder, multiple booting technique and FPGA.}, keywords = {Key Words,Viterbi decoder,multiple booting technique and FPGA}, title_ar = {تنفيذ مشفر لافوفي-حلال شفرة فيتربي باستخدام تقنية الإقلاع المتعدد على رقاقة FPGA}, abstract_ar = {الخلاصــة يعتبر المشفر اللافوفي أحد طرق تصحيح الخطأ الناتج عن إرسال البيانات. وهو جزء ضروري لأنظمة الأتصالات اللاسلكية مثل الجيل الثالث لأجهزة الهاتف المحمول والتي تستخدم بعض الصيغ لهذا المشفر وبالتالي تستخدم حلال الشفرة نوع فيتربي لأستعادة البيانات المرسلة. هنالك هياكل مختلفة للمشفر اللافوفي والتي تنقل متطلبات مختلفة لفاتح الشفرة. بتحوير بسيط للمقاطع الخاصة لفاتح شفرة فيتربي يمكن أن تستخدم في أنظمة ذات معدل شفرة وحجم بيانات وأطوال إرسال مختلفة. هذا البحث يستعرض تصميم وتنفيذ مشفر لافوفي ذو طول محدد 3 ومعدل سرعة مشفر 2/1 ، مع حلال شفرة فيتربي على لوح حاوي لـ مصفوفة البوابات القابلة للبرمجة حقليا نوع Spartan 3E (والمدعمة بـالرقاقة XC3S500E) باستخدام تقنية الإقلاع المتعدد. استخدمت لغة VHDL كوسيلة للتصميم المنطقي. في اللوح المذكور أعلاه وباستخدام تقنية الإقلاع المتعدد، تم تنفيذ تصميمين باستخدام ذاكرة الوميض الموجودة على اللوح المذكور، أحد التصميمين هو المشفر اللافوفي والاخر حلال شفرة فيتربي. تم تشكيل التصميم المحدد على مصفوفة البوابات القابلة للبرمجة حقليا أعتمادا على البرنامج المحمل من ذاكرة الوميض. بطريقة التشكيل هذه، فإن مصفوفة البوابات نفسها يمكن أن تعمل كمشفر لافوفي أو حلال شفرة فيتربي بالإستفادة من اعادة استخدام نفس الكيان المادي.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34888.html}, eprint = {https://rengj.mosuljournals.com/article_34888_2d849b963a79de49ee6a7a02e11364a6.pdf} } @article { author = {Ilham Majeed, Rasha}, title = {Design and FPGA Implementation of Takagi- Sugeno Fuzzy Controller Based on LUTs}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {81-94}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34908}, abstract = {Abstract In this paper, an approach for designing Fuzzy Controller based on Takagi-Sugeno inference engine with high computational speeds in architecture is proposed. The work focuses on advantages and disadvantages of Takagi-Sugeno control as compared with Mamdani's', in addition to focus on how computational complexity of the inference engine can be reduced and the speed of computation can be increased. Fuzzy Controller is implemented on FPGA using Look-Up Table (LUT). Whereas, each LUT is represented by Block RAMs in FPGA besides using number of arithmetic units in the design. To interface the design with users, a GUI program is designed using Visual Basic. Using JTAG port, the GUI's data can be stored in Block RAMs. Later, a designed Air Conditioning application is implemented and the practical results (in FPGA), theoretical results (computed by hand) and Matlab results are compared. Keywords: LUT, FPGA, JTAG port, Takagi-Sugeno Fuzzy Controller, GUI.}, keywords = {KEYWORDS,FPGA,JTAG port,Takagi,Sugeno Fuzzy Controller,GUI}, title_ar = {التصميم والبناء باستخدام FPGA لمسيطر مضبب نوع تاكاي- سوكينو باعتماد جدول البحث}, abstract_ar = {في هذا البحث , تم تصميم مسيطر مضبب يتألف من آلة استنتاج نوع تاكاي- سوكينو ويعمل بسرعة حساب عالية . خلال العمل, تم التركيز على مميزات السيطرة المضببة من نوع تاكاي- سوكينو بالمقارنة مع السيطرة المضببة من نوع مامداني بالإضافة إلى التقليل من تعقيد معمارية التصميم باستخدام مبدأ جدول البحث (LUT) للحصول على سرعة حساب عالية. حيث أنّ كل جدول بحث يُمثل بقالب ذاكرة في رقاقة FPGA بالإضافة إلى استخدام عدة وحدات حسابية في التصميم. ولتمكين تعامل المستخدم مع التصميم , تم تصميم واجهات المستخدم الرسومية (GUI) فضلا عن إرسال بيانات المسيطر المضبب إلى قوالب الذاكرة في رقاقة FPGA باستخدام منفذ JTAG . لتنفيذ واختبار المسيطر المصمم, تم تطبيق نظام التكييف الحراري في التصميم ومقارنة النتائج العملية مع النتائج المحسوبة نظريا فضلا عن النتائج المحسوبة باستخدام بيئة Matlab.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34908.html}, eprint = {https://rengj.mosuljournals.com/article_34908_ff0e33bd0feab7e2b7fd4a992bbac0b2.pdf} } @article { author = {F. M. Abdulla, Dr. and M. Ali, A. and A. Ibrahim, H.}, title = {INFLUENCE OF THE FORMING PROCESSES ON THE RATE OF CORROSION OF GALVANIZED HIGH STRENGTH LOW ALLOY STEEL SHEETS}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {18}, number = {6}, pages = {95-104}, year = {2010}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2010.34930}, abstract = {ABSTRACT: The effect of deformation on the corrosion of galvanized high strength low alloy steel sheet is studied. Specimens in the uniaxial, plain and biaxial strains were stretched by a hemispherical punch to three different punch heights for each path of strain. After each deformation, The deformed specimens together with a fourth non deformed specimen were subjected to a corrosive medium for the same sequential times. To determine the effect of corrosion, all the specimens were weighted before and after each corrosion stage and the hardness was also measured It was found that corrosion in the deformed specimens was higher than in the non-deformed ones. Also it was found that corrosion increased by moving from the uniaxial to the biaxial strain passing through the plain strain path and by increasing the punch heights. The results were verified by the hardness measurement. KEYWORDS: galvanized HSLA steel, corrosion, deformation, strain path}, keywords = {KEYWORDS,corrosion,Deformation,strain path}, title_ar = {أثر عمليات التشكيل على معدل تآكل صفائح الصلب عالي المقاومة منخفض العناصر السبائكية المغلون}, abstract_ar = {مستخلصتمت دراسة أثر التشكيل على معدل التآكل الكيميائي لصفائح الصلب عالي المقاومة منخفض العناصر السبائكية المغلون. شكلت نماذج ذات الانفعالات الاحادية الاتجاه و البسيطة والثنائية الاتجاه بواسطة الخرامة نصف الكروية الى ثلاثة اعماق مختلفة ولكل نوع من الانفعالات السابقة . بعد كل تشكيل عرضت النماذج المشكلة إضافة الى نموذج غير مشكل الى وسط ذو قابلية تآكل لفترات زمنية متعاقبة و متساوية لكافة النماذج. وجد أن التآكل الحاصل في النماذج المشكلة كان أكثر من ذلك الحاصل في النماذج غير المشكلة. كما وجد بأن التآكل ازداد بتغيير مسار الإنفعال من الأحادي الى الثنائي الاتجاه مرورا بالإنفعال البسيط وكذلك بزيادة عمق التشكيل لكافة النماذج. تم التحقق من النتائج بواسطة قياس الصلادة.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_34930.html}, eprint = {https://rengj.mosuljournals.com/article_34930_0c828d9801f9ea6e0d8474447e34ac7b.pdf} }