@article { author = {A. Majeed, Sura and N. Mahmood, Mohamad}, title = {Flexural Behavior Of Flat And Folded Ferrocement Panels}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {1-11}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43268}, abstract = {Abstract The present paper describes the results of testing folded and flat ferrocement panels reinforced with different number of wire mesh layers. The main objective of these experimental tests is to study the effect of using different numbers of wire mesh layers on the flexural strength of folded and flat ferrocement panels and to compare the effect of varying the number of wire mesh layers on the ductility and the ultimate strength of these types of ferrocement structure. Seven ferrocement elements were constructed and tested each having (600x380mm) horizontal projection and 20mm thick, consisting of four flat panels and three folded panels. The used number of wire mesh layers is one, two and three layers. The experimental results show that flexural strength of the folded panels increased by 37% and 90% for panels having 2 and 3 wire mesh layers respectively, compared with that having single layer, while for flat panel the increase in flexural strength compared with panel of plan mortar is 4.5%, 65% and 68% for panels having 1, 2 and 3 wire mesh layers respectively. The strength capacity of the folded panels, having the particular geometry used in the present study, is in the order of 3.5 to 5 times that of the corresponding flat panels having the same number of wire mesh layers. Both types are also analyzed using finite element method to check the flexural stresses in these panels under self weight and cracking load. Keywords: Ferrocement, Flat Panel, Folded panel, Mortar, Wire Mesh.}, keywords = {KEYWORDS,Flat Panel,Folded panel,mortar,Wire mesh}, title_ar = {تصرف الانثناء للالواح الفيروسمنتية المستوية والمطوية}, abstract_ar = {الخلاصة تتضمن الدراسة الحالية وصف لنتائج فحص صفائح فيروسمنتية مستوية وصفائح مطوية والمسلحة بأعداد مختلفة من المشبك السلكي. الهدف الرئيسي من هذه الفحوصات هو دراسة تأثير استخدام أعداد مختلفة من طبقات المشبك السلكي على مقاومة الثني لهذه الصفائح تحت تأثير حملين خطيين إلى حد الفشل, كل حمل يقع عند ثلث الفضاء وكذلك لمقارنة تأثير تغيير عدد طبقات المشبك السلكي على المطيلية والمقاومة القصوى لهذه الأنواع من المنشآت الفيروسمنتية. تم صب وفحص سبعة صفائح فيروسمنتية بأبعاد (600x380mm) وبسمك (20mm) , أربعة صفائح مستوية وثلاثة صفائح مطوية. كذلك تم تحليل كلا النوعي باستخدام طريقة العناصر المحددة لبيان اجهادات الثني لهذه الصفائح تحت تأثير وزنها إضافة إلى الحمل المسلط الذي سبب التشقق في الفحوصات العملية. كانت الأعداد المستخدمة من طبقات المشبك السلكي هي طبقة, طبقتين وثلاث طبقات. أظهرت النتائج العملية أن مقاومة الانثناء للصفائح المطوية تزداد بمقدار (37%) و (90%) للصفائح ذات الطبقتين والثلاث طبقات على التوالي, مقارنة مع الصفائح ذات الطبقة الواحدة, بينما تزداد مقاومة الثني للصفائح المستوية المسلحة مقارنة مع الصفيحة المستوية الخالية من المشبك السلكي بمقدار (68%), (65%), (4.5%) للصفائح المستوية التي تضم طبقة, طبقتين وثلاث طبقات من المشبك السلكي على التوالي. المقاومة القصوى للصفائح المطوية المستخدمة في الدراسة الحالية كانت حوالي (5-3.5) أضعاف مقاومة نظيرتها من الصفائح المستوية والتي تمتلك نفس العدد من طبقات المشبك السلكي}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43268.html}, eprint = {https://rengj.mosuljournals.com/article_43268_36dafb1602a9529ce1acbafb749b8980.pdf} } @article { author = {A. Mohamma, Zeena and A. Abdul Razzak, Ayad}, title = {Free Vibration Analysis Of Curved Box Girder Bridges by Higher Order Finite Strip}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {1-16}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43291}, abstract = {A higher-order conical frustum shell strip for analysis of free vibration of curved box girder bridges is developed, the auxiliary nodal line technique is used in the formation, the application of the motion equation by form the matrices of the stiffness and that of the consist mass of the strip and which has been mathematically derived by solving sixth and third order equations for bending and in plane actions respectively. Guyan reduction technique have been applied for each stiffness and the mass matrices of bridge. The strip which implies minimizing the degrees of freedom of the auxiliary nodal line of the Higher Order Finite Strip in order to reduce the size of the matrix from (15x15) to (8 x 8). The study has come out with very good results compared to the previous studies in terms of the natural frequencies for the first harmonic number of the box girder bridge section which is composed of two box cells with inclined webs. The ratio of difference between the present and previous studies have reached (6.73%) , while the natural frequencies for the seconed harmonic number of the same box section the ratio is about equal (3.765%) . Keywords: Box Girder Bridges, Free Vibration Analysis, Higher Order Finite Strip.}, keywords = {KEYWORDS,Free vibration analysis,Higher Order Finite Strip}, title_ar = {تحليل الاهتزاز الحر للجسور الصندوقية المنحنية بطريقة الشريحة المحددة ذات النسق العالي}, abstract_ar = {الخلاصةطورت شريحة قشرية ذات نسق عالي وشكل مخروطي ناقص لتحليل الاهتزاز الحر للجسور الصندوقية المنحنية، استعمل الخط العقدي المساعد في الاشتقاق، وطبقت معادلة الحركة بتكوين مصفوفة الجساءة ومصفوفة الكتلة المتجانسة للشريحة التي تم اشتقاقها رياضيا بحل معادلات من الدرجة السادسة والثالثة الخاصة بأفعال الانحناء والأفعال ضمن المستوي، فضلا عن ذلك تم تطبيق معادلات تكثيف كويان لكل من مصفوفة الجساءة والكتلة للجسر، لاختزال درجة حرية الحركة للخط العقدي المساعد للشريحة المحددة ذات النسق العالي لتحويل حجم المصفوفة من (15 15) إلى (8 8). أعطت الدراسة الحالية مقارنة مع الدراسات السابفة نتائج حيدة جدا للتردد الطبيعي من العدد التوافقي الأول لمقطع الجسر الصندوقي المؤلف من خليتين صندوقين ذات وترات مائلة إذ وصلت نسبة الفرق مابين الدراسة الحالية والسابقة إلى (6.73% )، أما بالنسبة للتردد الطبيعي من العدد التوافقي الثاني لنفس المقطع فقد وصلت نسبة الفرق إلى (3.76%) .الكلمات الدالة: تحليل الاهتزاز الحر، الجسور الصندوقية المنحنية، الشريحة المحددة ذات النسق العالي}, keywords_ar = {الكلمات الدالة,الجسور الصندوقية المنحنية,الشريحة المحددة ذات النسق العالي}, url = {https://rengj.mosuljournals.com/article_43291.html}, eprint = {https://rengj.mosuljournals.com/article_43291_68c94d4bfbf51727dd28badd83813e22.pdf} } @article { author = {Ramadhan Yousif, Ali}, title = {Prediction Of Ultimate Load Capacity Of High-Strength Reinforced Concrete Corbels}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {12-27}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43273}, abstract = {Abstract A study on the behavior of reinforced high-strength concrete corbels is carried out using nonlinear finite element analysis and a simplified softened strut-and-tie model. In the numerical analysis, eight-node isoparametric plane stress elements are employed to model the concrete material. An elastic-strain hardening plasticity approach combined with cracking damage is used in modeling the concrete behavior. The reinforcing bars are treated as embedded elements and are considered as elastic-perfectly plastic material. In the analytical method, the analysis is based on truss analogy following the provisions of Appendix A of the ACI 318-05 Code. Strength predictions of both methods correlate well with the 34 test results of corbels available from the literature. It was concluded that the adopted finite element model is a powerful tool for the analysis of such disturbed region. Also the simple truss model used proved to be a suitable design tool for these members. The finite element method can be used in conjunction with the truss analogy for optimum design. Keywords: corbels; deep beams; finite element; non-flexural members; plasticity; shear strength; strut-and-tie models.}, keywords = {KEYWORDS,deep beams,finite element,non,flexural members,Plasticity,Shear Strength,Strut,and,tie models}, title_ar = { التحمل الأقصى للكتائف الخرسانية المسلحة عالية المقاومة}, abstract_ar = {الخلاصةتم في هذا البحث دراسة سلوك الكتائف الخرسانية المسلحة عالية المقاومة بالتحليل غيرالخطي بأستخدام العناصر المحددة ، وكذلك بأستخدام مسنم بسيط. تم في التحليل العددي أستخدام العناصرالمحددة ذات الثمانية عقد في تمثيل الخرسانة بطريقة الأجهاد في المستوي وبالأعتماد على التصرف المرن - تصلب الأنفعالات اللدن في الأنضغاط بالأشتراك مع سلوك الخرسانة عند التشقق في حالة الشد. تم تمثيل قضبان التسليح داخل الخرسانة بحيث تتحمل قوى محورية بأعتبارها مادة مرنة - تامة اللدونة. أما في التحليل الأعتيادي فقد تم الأعتماد على مسنم بسيط وبأستخدام التوصيات الواردة في الملحقA للمدونة الأمريكية للخرسانة ACI 318-05 . أبدت نتائج التحليل توافقا جيدا عند مقارنتها مع النتائج العملية المستحصلة من فحص أربع وثلاثين كتفا متوفرا في الدوريات السابقة. لقد أستنتج بأن تمثيل الخرسانة المسلحة المستخدم في العناصر المحددة طريقة كفوؤة لتحليل هذه الأعضاء الخرسانية المضطربة. كما أن المسنم البسيط الذي أعتمد في التحليل أبدى كفائته بشكل جيد كأداة لتصميم الكتائف. يمكن أستخدام طريقة العناصر المحددة وبالتداخل مع طريقة المسنمات للحصول على أفضل تصميم.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43273.html}, eprint = {https://rengj.mosuljournals.com/article_43273_ed9316f9c05f20d9551a6475e239d941.pdf} } @article { author = {S. Al-Luhybi, Ashtar and J. Al-Sulayfani, Bayar}, title = {Effect Of Externally Bonded Gfrp Sheets On The Shear Transfer Capacity Of Concrete}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {17-27}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43293}, abstract = {Abstract The current research includes practical results of study and investigated the subject of strengthening the shear strength through uniaxial confinement (one direction) using GFRP Sheets. This study was carried out by casting eight specimens (the push-off specimens group) which was divided in to four groups, the first non confined, being the reference group, the remaining groups consisted of two specimens each with only one variable being the degree of strengthening that is the numbers of confinement layers. The second, third, and fourth group were confined with one, tow, and three layers respectively. All specimens were tested through the application of a vertical load up to failure. The result indicated that there is a clear indication of shear strength increase amounting to 33% relative to the reference specimens (non confined), also there was a noticeable increase in the absorption capacity as a function of the number of confinement layers. Key words: Strengthening, Shear Transfer on concrete, GFRP Sheets, Push-off specimens.}, keywords = {Key Words,Shear Transfer on concrete,GFRP Sheets,push,off specimens}, title_ar = { تأثير التغليف الخارجي بصفائح الألياف الزجاجية على مقاومة انتقال القص المباشر للخرسانة}, abstract_ar = {يحتوي هذا البحث على نتائج عملية لدراسة تقصّت عن موضوع التقوية الحاصلة في مقاومة انتقال القص المباشر للخرسانة باستخدام التغليف الأحادي الاتجاه بوساطة صفائح الألياف الزجاجية.أُجريت هذه الدراسة من خلال صب ثمان نماذج من نماذج نوع الدفع(Push-off Specimens) قسمت هذه النماذج إلى أربع مجاميع، المجموعة الأولى لم تغلف على اعتبار أنها نماذج مرجعية أما باقي المجاميع فتتألف من نموذجين المتغير الوحيد في هذه المجاميع هو درجة التقوية أو بالأحرى عدد طبقات التغليف، إذ تم تغليف المجموعة الثانية والثالثة والرابعة بطبقة وطبقتين وثلاث طبقات على التوالي، فُحصت هذه النماذج من خلال تسليط قوة عمودية على النموذج ولغاية الفشل، بعد إجراء الفحص أظهرت النتائج أن هناك زيادة واضحة في مقدار مقاومة انتقال القص للنماذج المغلفة بثلاث طبقات وصلت إلى حوالي (33%) نسبة إلى النماذج غير المغلفة، كما أن هناك زيادة واضحة في طاقة الامتصاص للنماذج تبعاً بزيادة طبقات التغليف.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43293.html}, eprint = {https://rengj.mosuljournals.com/article_43293_c3287456ffeed829e3dc102903f5baca.pdf} } @article { author = {Ahmed Mahmood, Yasser and Ali Al-Nimma, Dhaiya}, title = {Modeling and Computer Simulation of a Dual Converter System}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {28-35}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43294}, abstract = {Abstract DC Drives have been used and still being used in many industrial applications as adjustable speed drives. Among these applications are robotics, mill, steel, cement…etc, [1] industries. The dual converters are the most common power electronics equipments that are used in driving DC motors. Each converter drives the motor in two different quadrants in the torque-speed diagram, thus the drive system becomes a four-quadrant. Computer Simulation results has been obtained for the steady state condition. The results are in the form of motor and converters currents and voltages for different trigger angles. In order to validate the simulated results, practical results have been obtained for the same triggering angles. For dynamic conditions such as starting condition have been obtained practically and compared with the simulated results, be sides that studying some abnormal conditions such as fault condition with in the motor or in the dual converter. Key words: DC drives, simulation of DC drive, dual converter.}, keywords = {Key Words,simulation of DC drive,dual converter}, title_ar = {النمذجة والتمثيل على الحاسبة لمنظومة المغير المزدوج}, abstract_ar = {الخلاصةتعد جرارات التيار المباشر من أقدم الجرارات التي استخدمت في التطبيقات الصناعية والتي من أهمها صناعة الطواحين صناعة عجينة الورق والصلب. تعد دائرة المغير المزدوج إحدى أبرز دوائر إلكترونيات القدرة التي تستخدم في سوق محركات التيار المباشر. إذ يختص كل مغير فيها بتشغيل المحرك بربعين مختلفين ضمن مخطط العزم-السرعة لتصبح بذلك هذه الدائرة مع المحرك جرار التيار المباشر الرباعي. تم الحصول على نتائج تشغيل للحالة المستقرة لفولتيات وتيارات المحرك والمغيرين عند زوايا قدح مختلفة. وللتأكد من مدى صحة نموذج التمثيل على الحاسبة بمحاكاة النموذج ألمختبري العملي, تم الحصول على نتائج عملية في المختبر ومقارنتها بنتائج التمثيل، كما تم الحصول على بعض الحالات الحركية مثل البدء وتم مقارنة النتائج العملية مع نتائج التمثيل. يضاف إلى ذلك كله بعض حالات تشغيل غير طبيعية مثل حالات العطب وذلك من خلال النموذج الحاسوبي.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43294.html}, eprint = {https://rengj.mosuljournals.com/article_43294_b63a36e25f7dba13d9a8721a90dcaf3d.pdf} } @article { author = {Burhan Abdurrahman, Rana and Hakeem Hamed Ahmad, Abdul}, title = {Effect of Elevated Temperature on Some Properties of Air-Entrained Steel Fibers Reinforced Concrete}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {28-41}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43276}, abstract = {Abstract In this paper, an experimental investigation was conducted to explore the mechanical properties of air entrained steel fibers reinforced concrete (AESFC). The residual mechanical properties measured include compressive and splitting tensile strengths, modulus of elasticity and (stress – strain) curves. Air-entrained concretes (AECs) were prepared with different steel fibers content (0, 0.4, 0.8, and 1.2) % added to enhance the strength of concrete. After exposure to high temperature included (200, 400, 600) ◦C, the residual mechanical properties of AESFC were investigated and compared with normal concrete. Test results showed reduction in properties by different ratio for all types of concrete after exposure to elevated temperature, the tensile strength and elastic modulus deteriorated with temperature more than the compressive strength. Using steel fibers seems effective in minimizing the degradation of strength for the concrete. Results showed also that the decrease in compressive strength after exposure to high temperature could be reduced by increasing volume of samples. Heating accompanied with weight losses and color changes became clearer at (400 – 600) ◦C exposure. Key words: Air entrained concrete; steel fibers ; elevated temperature}, keywords = {Key Words,Steel Fibers,elevated temperature}, title_ar = {تأثير الحرارة العالية في بعض خصائص الخرسانة ذات الهواء المقصود المسلحة بالالياف الفولاذية}, abstract_ar = {الخلاصة اشتمل البحث على دراسة عملية لبعض الخصائص الميكانيكية التي تضمنت مقاومة الانضغاط، الشد الانشطاري، معامل المرونة وعلاقة (الإجهاد – الانفعال) للخرسانة المقصودة الهواء والمسلحة بالألياف الفولاذية ومدى تأثير الحرارة العالية فيها ومقارنة النتائج مع الخرسانة الاعتيادية، حيث تضمن البحث إضافة مضاف الهواء المقصود إلى مزيج الخرسانة الاعتيادية بنسبة (%2) من وزن الاسمنت وتسليح الخرسانة الناتجة بألياف فولاذية ذات مقطع غير منتظم حيث استخدمت ثلاث نسب حجمية من الألياف فضلاً عن المزجة بدون ألياف وهي (0.4 1.2,0.8,) % وتم تسخين النماذج إلى ثلاثة مستويات حرارية عالية ºC (200 ،400 ،600) لمدة ساعة واحدة وبدون تسليط أي حمل أثناء التسخين. بعد التعرض للحرارة العالية انخفضت الخصائص الميكانيكية بصورة سلبية وبنسب مختلفة للمزجات جميعًا وكان تأثر مقاومة الشد الانشطاري ومعامل المرونة بارتفاع الحرارة أكبر من مقاومة الانضغاط، وعند مقارنة المزجات الخرسانية مع بعضها البعض ومع الخرسانة الاعتيادية لوحظ أن وجود الألياف قد قلل من الانخفاض وأعطى امتصاصًا أعلى للطاقة عند درجات الحرارة العالية، كما تبين أن الفقدان في مقاومة الانضغاط يمكن أن يقل بزيادة حجم النموذج، وتخلل الفحص حدوث التشظي المتفجر لبعض نماذج الفحص في أثناء التسخين كما سبب التسخين انخفاض في الوزن وحدوث تغييرات لونية بدت أكثر وضوحًا عند درجتي الحرارة ºC (600 ،400).}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43276.html}, eprint = {https://rengj.mosuljournals.com/article_43276_7ec4ae76ed641af7cadd303aa6f33679.pdf} } @article { author = {M. Jajoo, Nawal}, title = {Improved Equations for Estimating Spray Losses of Fixed Sprinkler Irrigation Systems in Iraq}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {36-41}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43298}, abstract = {Many local field studies on sprinkler spray losses in Iraq have been conducted, the first was in 1980 and the latest is in 2008. Many equations to estimate these losses have been proposed. But, most of these studies depended on narrow ranges in the values of the parameters and variables involved. Therefore, there may be great risk in applying these equations in the design and management of sprinkler irrigation systems. Add to that, the problem of unavailability of data for some of the variables involved which makes the use of these equations impossible. Thus, this study presented a group of 14 prediction equations for the sprinkler spray losses, so that it becomes possible to estimate these losses if one or more of the following main variables is available: air temperature, wind speed, relative humidity, nozzle size, and operating pressure head. The derivation of the proposed equations depends on all available local field data, thus making these equations more accurate and general. Key words: Sprinkler irrigation, sprinkler spray losses, sprinkler irrigation in Iraq.}, keywords = {Key Words,sprinkler spray losses,sprinkler irrigation in Iraq}, title_ar = { تطوير معادلات تخمين فواقد رذاذ نظم الري بالرش الثابتة في العراق}, abstract_ar = {الخلاصةاجريت محليا في العراق العديد من الدراسات الميدانية حول موضوع فواقد رذاذ الري بالرش كان أولها عام 1980 وآخرها عام 2008 وقدمت العديد من المعادلات لتخمين هذه الفواقد إلا ان معظم هذه الدراسات اعتمدت مديات ضيقة او صغيرة للعديد من المتغيرات والعوامل التي تضمنتها المعادلات المقترحة مما يشكل خطورة في تعميم مثل هذه المعادلات حيث قد ينجم من تطبيقها اخطاء جسيمة في حقل العمل. ثم أن هناك مشكلة احتمالية عدم توفر قيم أو بيانات لبعض العوامل أو المتغيرات الداخلة في هذه المعادلات مما يتعذر في مثل هذه الحالة تطبيق المعادلة، لذا قدم البحث الحالي حزمة من المعادلات التخمينية المطورة (14 معادلة) بحيث يمكن تخمين فواقد رذاذ الري بالرش في حالة توفر متغير واحد أو أكثر من المتغيرات الرئيسة: درجة الحرارة، سرعة الريح، الرطوبة النسبية، قطر مبثق المرشة، وشحنة الضغط التشغيلي. وقد تم اعتماد كافة البيانات المتوفرة سابقا" حول الموضوع وما توفر عنه في السنوات الأخيرة مما يجعل هذه المعادلات أكثر دقة وشمولية.كلمات دالة: الري بالرش، فواقد رذاذ الرش، الري بالرش في العراق، تخمين فواقد رذاذ الري بالرش.}, keywords_ar = {كلمات دالة,فواقد رذاذ الرش,الري بالرش في العراق,تخمين فواقد رذاذ الري بالرش}, url = {https://rengj.mosuljournals.com/article_43298.html}, eprint = {https://rengj.mosuljournals.com/article_43298_943b6e9ce3670cc15c59c82546046136.pdf} } @article { author = {Y.Kahwaji, Ghalib and M. Al-Makhyoul, Ziad}, title = {Validation Of The Total Resistance Heat Dissipation Model For Heat Transmission Through Annular Fins With Variable Heat Transfer Coefficient}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {42-50}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43280}, abstract = {The present paper includes analytical investigation of the validity of total resistance heat dissipation model using variable heat transfer coefficient for annular fins constant thickness. The model is given as: Furthermore, a finite difference method using SOR technique is devised to serve the two purposes of verifying the two dimensional heat transfer model and to cover a wide range of fin parameters and heat transfer coefficient models. The results were in agreement and proved the validity of the suggestion model under the both the constant and variable heat transfer coefficient assumptions. Key words: Total resistance, Variable heat transfer coefficient, Heat transfer, Annular fins}, keywords = {Key Words,Variable heat transfer coefficient,Heat transfer,Annular fins}, title_ar = { تحقيق نموذج المقاومة الكلية لانتقال الحرارة في الزعانف الحلقية باستخدام معامل انتقال حرارة متغير}, abstract_ar = {الخلاصةتضمن البحث الحالي إجراء تحقيق لصحة نموذج المقاومة الكلية لانتقال الحرارة تحليليا باستخدام معامل انتقال حرارة متغير لزعنفة حلقية ثابتة السمك. النموذج ممكن إعطاءه كالآتي: ولذلك تم استخدام تحليل الفروق المحددة باستخدام تقنيةSOR كحل إضافي ليلائم الغرضين نموذج انتقال الحرارة بالاتجاهين ولتغطية مدى واسع من متغيرات الزعنفة ومعامل انتقال الحرارة. ظهرت النتائج متوافقة ومن ثم إثبات صحة النموذج الرياضي للمقاومة الكلية لانتقال الحرارة عند فرضيات معامل انتقال حرارة ثابت ومتغير.}, keywords_ar = {الكلمات المفتاحية,معامل انتقال حرارة متغير,انتقال الحرارة,الزعانف الحلقية}, url = {https://rengj.mosuljournals.com/article_43280.html}, eprint = {https://rengj.mosuljournals.com/article_43280_a869fc7b2524841cbdeb42d225a81e6e.pdf} } @article { author = {Nasiralla AL-Talib, Azza and Abd AL-Majeed Hayawi, Hana}, title = {Laboratory Study of Flow Energy Dissipation Using Stepped Weirs}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {42-51}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43300}, abstract = {A laboratory study was conducted on stepped and unstepped weirs in order to find their efficiency of dissipating flow energy. Thirty six weirs were constructed and tested to compare between stepped and unstepped weirs in flow energy dissipation, twenty seven of them were stepped while the rest were unstepped. Three heights of stepped weirs (P=36,45,54)cm were used with different numbers of steps (n=9,12,15) , and three downstream slopes of stepped face (h/l=1/2,1/3,1/4) were tested, while for unstepped weirs one height of weir (P=54)cm and three downstream slops (α=26.6o,18.4o,14o) were tested. The results showed that increasing height of weir and decreasing both number of steps and downstream slops stepped face of the weir will cause an increase of the ratio of flow energy dissipation, and the stepped weirs are more efficient in flow energy dissipation compared with unstepped weirs. The percentage of flow energy dissipation (E%) is increased by increasing the ratio of height of weir to critical water depth (P/dc), the ratio of length of the step to critical water depth (l/dc) and the ratio of height of step to critical water depth (h/dc) while it decreases by increasing the discharge (Q). Imperical relationships between the ratio of flow energy dissipation and factors affecting it were obtained in stepped weirs.}, keywords = {}, title_ar = {دراسة مختبرية لتبديد طاقة الجريان باستخدام الهدارات المدرجة}, abstract_ar = {الخلاصة:أجريت دراسة مختبرية على هدارات مدرجة وغير مدرجة ، لمعرفة كفاءتها في تبديد طاقة الجريان،حيث تم إنشاء واختبار (36) نموذجاً ، منها (27) هدار مدرج و(9) هدارات غير مدرجة للمقارنة بينهما في تبديد طاقة الجريان.واستخدمت ثلاثة ارتفاعات للهدارات المدرجة (P=36,45,54) سم بأعداد مختلفة للدرجات (n=9,12,15) وميول التدرج (h/l=1/2,1/3,1/4)، أما بالنسبة للهدارات غير المدرجة فقد استخدم ارتفاع واحد (P=54) سم وثلاثة ميول لمؤخر الهدارات (α=26.6o,18.4o,14o). أوضحت نتائج الدراسة أن زيادة ارتفاع الهدار (P) وتقليل كل من عدد الدرجات (n) وميل التدرج (h/l) يؤدي إلى زيادة نسبة تبديد طاقة الجريان (E%)، كما أكدت الدراسة أن الهدارات المدرجة أكثر كفاءة في تبديد طاقة الجريان مقارنةً بالهدارات غير المدرجة ، وأن نسبة تبديد طاقة الجريان تزداد بزيادة نسبة ارتفاع الهدار إلى عمق الماء الحرج (P/dc) ونسبة طول الدرجة إلى عمق الماء الحرج (l/dc) ونسبة ارتفاع الدرجة إلى عمق الماء الحرج (dc اh) بينما تقل بزيادة التصريف (Q). كما تم التوصل إلى علاقات رياضية بين نسبة تبديد طاقة الجريان والعوامل المؤثرة عليها في الهدارات المدرجة.كلمات الدلالة: هدار مدرج، تبديد الطاقة.}, keywords_ar = {كلمات الدلالة,تبديد الطاقة}, url = {https://rengj.mosuljournals.com/article_43300.html}, eprint = {https://rengj.mosuljournals.com/article_43300_345a75c8a892adf2d998f7f9cbc7120a.pdf} } @article { author = {Ibraheem saeed, Ramiz and Ahmed Ali, ed}, title = {Numerical Study of Natural Convection Heat Transfer of a Square Eccentric Body Buried in a Porous Media}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {51-62}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43283}, abstract = {Abstract Natural convection in a saturated porous medium bounded by two horizontal eccentric ducts is studied numerically by solving the governing Darcy-Boussinsq equations using finite differences on very fine grid. This paper reports the effect of the position of a cooled square body with respect to the centre of the square cavity vertically and horizontally. The numerical results of heat transfer are presented for modified Rayleigh number Ra* (based on width of cavity) in the range (50 to 400) and for different size of the body with respect to the width of the cavity (0.25x0.25,0.3x0.3,0.5x0.5) and six positions of the body respect to the center of cavity. The results are represented by streamlines and isotherms to show the behavior of the flow and temperatures distribution. Also some graphics had been obtained which represent the relationship between Nusselt and Rayleigh numbers with eccentricity. (Key words: natural convection, porous medium, cavity) Key Words : Porous medium , Thermal nonequilibrium , Heat transfer , Natural convection.}, keywords = {Key Words,Thermal nonequilibrium,Heat transfer,Natural Convection}, title_ar = {دراسة عددية لانتقال الحرارة بالحمل الطبيعي لجسم مربع مغمور لا مركزيا في وسط مسامي}, abstract_ar = {تم إجراء دراسة عددية للحمل الطبيعي لوسط مسامي مشبع محصور بين مجريين مربعين غير متمركزين وذلك بواسطة حل المعادلات المتحكمة لدارسي – بوسنسك باستخدام طريقة الفروق المحددة على شبكة ناعمة جدا. في هذا البحث تم تناول تأثير موقع الجسم المربع البارد نسبة إلى مركز التجويف عموديا وأفقيا. تمثلت النتائج العددية لانتقال الحرارة بعدد رالي المطور (نسبة إلى عرض التجويف ) في المجال (50-400) وإحجام متعددة للجسم ( (0.25x0.25,0.3x0.3,0.5x0.5 ولستة مواقع للجسم نسبة الى مركز التجويف. تمثلت النتائج بخطوط الانسياب وخطوط درجات الحرارة التي تظهر صيغة الانسياب وتوزيع درجات الحرارة. كذلك تم الحصول على بعض الرسومات البيانية التي مثلت العلاقة بين عدد نسلت وعدد رالي مع اللا تمركزية.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43283.html}, eprint = {https://rengj.mosuljournals.com/article_43283_db1c78c638b24a68139ae81a2986e572.pdf} } @article { author = {Noory Saeed, Uriya and Taha Abdulla, Nahith}, title = { The alteration of designer logical performance during architectural design task}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {52-66}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43304}, abstract = {Although many studies have tried to reduce differences between conceptual models of thinking processes, through the description of the operational performance of any intellectual task includes problem solving, however, because of the design specificity in this regard, and diversity of its motion, there were always, many of obstacles that stand in the way of developing a model describes the operations of reasoning achievement during different architectural design phases. The need for explicit language of designer thinking, and architects performance or how they underlined such aspects, was incentive concern for many contemporary studies, which tried to cover this area in one way or another. This research tries to investigated designer logical behavior during a design process, through the review of inference acts, during conceptual stage of that process, also it tries to investigate the nature of the mobility of this behavior across time of the task. Keywords: Logic, Logical Structure, Architectural Inference, Architectural Design}, keywords = {KEYWORDS,Logical Structure,Architectural Inference,architectural design}, title_ar = {تغير الأداء المنطقي للمصمم عبر زمن المهمة التصميمية في العمارة}, abstract_ar = {الخلاصةرغم أن العديد من الدراسات قد حاولت، تقليص الفرق بين النماذج المفاهيمية التي تعرضت لحصر العمليات الفكرية، من خلال توصيفها للجانب المعرفي و العملياتي المرتبط بأداء أي مهمة فكرية (تتضمن إجابة تساؤل أو حلا لمشكلة ما)، إلا أنه ولما للتصميم من خصوصية في مجاله المعرفي، وما للعملية الفكرية من سعة جانبها الإجرائي، فلقد كان هنالك دوما العديد من العقبات التي تقف عائقا أمام وضع نموذج معرفي عام يصف عمليات الانجاز المنطقي أثناء القيام بالمهام التصميمية المختلفة بما فيها عملية التصميم المعماري. إن الحاجة إلى لغة معلنة للجوانب التي يفكر فيها المصمم، وأداءه أو الكيفية التي تقوم عليها مثل تلك الجوانب، كان حافزا مهما للعديد من الدراسات المعاصرة، التي حاولت التقرب من هذا المجال. يحاول البحث التحري عن السلوك المنطقي للمصمم أثناء قيامه بالفعل التصميمي وذلك من خلال استعراض أساليب الاستدلال التي يمر بها تفكير المصمم في المرحلة المفاهيمية للعملية التصميمية والتي يكون حصيلتها غالبا إنتاج الحلول للمشاكل التصميمية وطبيعة حراك هذا السلوك عبر زمن المهمة التصميمية في تلك المرحلة من خلال ملاحظة تغير ذلك السلوك ضمن تجربة اداء مهمة تصميمية، كمحاولة لبناء نموذج أبستمولوجي يعلن الأداء الفكري للمصمم ويضع الخطوط العامة لطبيعة تغير ذلك الأداء.كلمات مفتاحيه: المنطق، البنية المنطقية، الاستدلال المعماري، التصميم المعماري}, keywords_ar = {كلمات مفتاحيه,البنية المنطقية,الاستدلال المعماري,التصميم المعماري}, url = {https://rengj.mosuljournals.com/article_43304.html}, eprint = {https://rengj.mosuljournals.com/article_43304_3481410d4d56a2839dc727aabec2092b.pdf} } @article { author = {Hazim saber, Aws and Ahmed Khalil, Rafid}, title = {FPGA Implementation of Adaptive Noise Canceller}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {63-72}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43287}, abstract = {This paper presents hardware implementation of least mean square (LMS) adaptive filter based Adaptive Noise Canceller (ANC) structure on FPGA using VHDL hardware description language. First, the adaptive parameters are obtained by simulating ANC on MATLAB. Second, the data, processed by FPGA, such as step size, input and output signals, desired signal, and coefficients of ANC, are exactly expressed into fixed-point data representation. Finally, the functions of FPGA-based system structure for such LMS algorithm in time sequence are synthesized, simulated, and implemented on Xilinx XC3S500E FPGA using Xilinx ISE 9.2i developing tool. The research results show that it is feasible to implement, on chip train, and use adaptive LMS filter based ANC in a single FPGA chip. Keywords: Adaptive noise canceller, least mean square, FPGA, Adaptive FIR filter}, keywords = {KEYWORDS,least mean square,FPGA,Adaptive FIR filter}, title_ar = {تنفيذ نظام إلغاء الضوضاء المتكيف باستخدام مصفوفة البوابات المبرمجة حقليا}, abstract_ar = {الخلاصةيعرض هذا البحث تنفيذ المرشح المتكيف المبني على خوارزمية معدل المربع الأقل (LMS) المستخدم في بنية نظام إلغاء الضوضاء المتكيف (ANC) على شريحة مصفوفة البوابات المبرمجة حقليا (FPGA) باستخدام لغة وصف الكيان المادي VHDL.أولا تم أيجاد العوامل المتكيفة لنظام ANC وذلك من خلال محاكاة نموذج ANC في البيئة البرمجية MATLAB. ثانيا إيجاد التمثيل المناسب لمعاملات المرشح و إشارات الإدخال و الإخراج باستخدام بيانات النقطة الثابتة و إيجاد كبر الخطوة المناسب لتنفيذ نظام ANC .و أخيرا تم التركيب النهائي لنظام ANC المبني على خوارزمية LMS ومحاكاتها و تنفيذها على شريحة Xilinx XC3S500E FPGA باستخدام أدوات التطوير ISE9.2i الخاصة بشركة Xilinx . أوضحت نتائج البحث إمكانية تنفيذ المرشح المتكيف المستخدم في ANC وتدريبه داخل الشريحة باستخدام شريحة FPGA واحدة.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43287.html}, eprint = {https://rengj.mosuljournals.com/article_43287_3137622f3ac963c83750741c6cb2f6d2.pdf} } @article { author = {A. M. Alkurukchi, Miqdam}, title = {Spatial and Visual Organization Properties of Mosul University Components}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {67-79}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43305}, abstract = {Abstract Spatial organization is the operative mean through which built environment expresses the Purposes of its creation. Due to its ability to provide basic requisites of movement, encounter and avoidance patterns, Modern Studies assume Spatial Organization as the main generator of Social life. Syntactical relations of Spatial and Visual organization for Mosul University Campus components, represents phenomena that lacks adequate research endeavors, despite its importance as a social organization phase, and a human mode of reaction. Accordingly, this paper aims to explain these relations. Using Space Syntax methodology, a number of findings were obtained, explaining Spatial and Visual properties of Mosul University Campus components.}, keywords = {}, title_ar = {خصائص التنظيم الفضائي والبصري لمكونات حرم جامعة الموصل}, abstract_ar = {الخلاصةيعد التنظيم الفضائي احد الوسائل الفعالة التي تعبر البيئات المبنية من خلالها عن الغايات التي أنشئت من اجلها، وذلك عن طريق توفيره المتطلبات الأساسية لأنماط الحركة، وانماط الألتقاء والعزل والتي عدتها الدراسات الحديثة المولدات المادية للحياة الأجتماعية.مثلت علاقات التنظيم الفضائي والبصري لمكونات حرم جامعة الموصل ظاهرة لم تنل نصيبا كافيا من الدراسة، رغم اهمية هذا التنظيم بوصفه شكلا للتنظيم الأجتماعي واسلوب للعمل الإنساني يعطي معنى للفضاء من خلال الأندماج والأنفصال. بالتالي فقد استهدف البحث التعرف على خصائص التنظيم الفضائي والبصري لحرم الجامعة، وبتطبيق منهجية قواعد تركيب الفضاء، تم قياس المتغيرات، وقد وضحت النتائج طبيعة العلاقات التركيبية للتنظيم الفضائي والبصري لمكونات حرم جامعة الموصل.الكلمات الدالة: التنظيم الفضائي، حرم جامعة الموصل، مخطط التكامل البصري.}, keywords_ar = {الكلمات الدالة,حرم جامعة الموصل,مخطط التكامل البصري}, url = {https://rengj.mosuljournals.com/article_43305.html}, eprint = {https://rengj.mosuljournals.com/article_43305_d21d18d03b1e8541c98a34d3e751b038.pdf} } @article { author = {Nawfal Abd Alrazaaq, Sura and Hamid Ali, Fakhraldeen}, title = {Fuzzy Self Tuning Of Dc Position Control Based On Labview}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {73-83}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43288}, abstract = {Abstract This paper investigates the effect of quantization gain factors, at the input side, and the scaling gain, at the output side, of a fuzzy controller. A fuzzy control system is designed with two main parts: a basic fuzzy controller (BFC) which produces the output control signal and supervisor fuzzy controllers (SFCs) to continuously adjust, on-line, the I/O scaling or gain factors of the (BFC) in order to improve its performance against different dynamic operating conditions. The designed self tuning controller is used to position control of a DC motor with un known parameters according to the feed back inputs, a tracking error (e) and change of error (Δe), based on the proposed fuzzy rules. The system implementation and tests are carried out using LabVIEW software ( V8.2 ) with a data acquisition card type (NI PCI-6251) from National Semiconductors to achieve real time measurements. Keywords: self-tuning, fuzzy controller, position control, scaling gain, LabVIEW .}, keywords = {KEYWORDS,tuning,fuzzy controller,position control,scaling gain,LabVIEW}, title_ar = {التنغيم الذاتي المضبب للسيطرة على الموقع في بيئة LABVIEW}, abstract_ar = {وبالاستعانة ببطاقة طلب البيانات ( NI PCI-6251 ).}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_43288.html}, eprint = {https://rengj.mosuljournals.com/article_43288_951c74fd4f5ac40a305324f5d2770b2c.pdf} } @article { author = {A. H. Al-Tuhafi, Assda and I. M. Al-Aane, Talaat and F. M. Al-Daudi, Khawla}, title = {The Formal Composition of Khans in Islamic Architecture (An Analytical Study)}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {17}, number = {4}, pages = {80-96}, year = {2009}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2009.43312}, abstract = {Abstract Islamic architecture is considered to be a unique example that reflects the impact of structural formation systems in establishing its form; the structural relations represent the most important items and bases of architectural structures, especially at the abstract level. The structural relations form the basic foundation which represent the most important aspect in producing the formal structure of any building thus they are considered to be the most important method in describing the physical reality of architectural production . Stemming from the above fact, the study focuses on the structural relations that form the plans. The problem of the study is that structural relations which form the plans of Khans buildings in Islamic architecture are not clear. The aim of the present study is to clarify the specialty of Muslim architect intellectuality in the formation of a particular mechanism or method to form and design studied plans with specific functions like khans. To achieve the aim of the study a theoretical framework of structural relations is built depending on modern studies on formation of those relations on the bases of the statistical analytical method. The results arrived at show that the structural relations which form and construct the plans of Khans buildings are characterized by uniqueness as a distinguishing character of Islamic architecture some of these types of building are the khans, though they differ in their architectural design, their date and ever their geographical location. This in turn gives an indication and proof of the Muslim architect creative role in determine the distinguished identity of his architecture with the incentive of Islamic cultural intellect held by that architect all over the places of his civilization whenever and wherever he exists. Key Word : Formal Composition , Relationships Formative , Khan , Islamic architecture}, keywords = {Key Word,Relationships Formative,Khan,Islamic architecture}, title_ar = {التكوين الشكلي للخانات في العمارة الإسلامية (دراسة تحليلية)}, abstract_ar = {تعتبر العمارة الإسلامية مثالا متميزا ينعكس من خلالها اثر نظم التكوين الشكلي في خلق عمارتها،فقد مثلت (العلاقات التكوينية) أهم المفردات والأسس للتكوينات المعمارية ولاسيما في المستوى التجريدي لهذه التكوينات ،فقد شكلت هذه العلاقات القاعدة الأساسية التي بدورها مثلت الجانب الأهم في إنتاج التكوين الشكلي لأية عمارة، وبذلك فهي تمثل من أهم السبل في وصف الحقيقة الفيزياوية للنتاج المعماري. وبناء على ذلك فقد تم التركيز على موضوع العلاقات التكوينية التي تشكل المخططات، وحددت مشكلة البحث بعدم وضوح العلاقات التكوينية التي تشكل مخططات أبنية الخانات في العمارة الإسلامية. وتركز هدف البحث في توضيح خصوصية فكر المعمار المسلم في تشكيل آلية أو طريقة معينة لتكوين وتصميم مخططات مدروسة ذات وظائف محددة مثل (الخانات). ولتحقيق هدف البحث فقد تطلب بناء اطار نظري لبعض العلاقات التكوينية بالاعتماد على الدراسات الحديثة في تشكيل تلك العلاقات وتم الاعتماد على المنهج التحليلي الاحصائي. وتبين الاستنتاجات التي توصل إليها البحث إن (العلاقات التكوينية) التي تشكل وتكون شكل المخططات في أبنية الخانات تمتاز بالوحدة كصفة مميزة للعمارة الإسلامية وضمن هذا النوع من المباني (الخانات) على الرغم من اختلاف طرازها المعماري وفترتها الزمنية وحتى موقعها الجغرافي، وهذا بدوره يعطي مؤشرا ودليلا على دور الإبداع الذي يمتلكه المعمار المسلم في تحديد الهوية المتميزة لعمارته وذلك بدافع وحدة الفكر الحضاري الإسلامي الذي كان يحمله ذلك المعمار على عموم بقاع حضارته متى وأين ما كان.الكلمات المفتاحية : التكوين الشكلي ، العلاقات التكوينية ، الخانات ، العمارة الإسلامية}, keywords_ar = {الكلمات المفتاحية,العلاقات التكوينية,الخانات,العمارة الإسلامية}, url = {https://rengj.mosuljournals.com/article_43312.html}, eprint = {https://rengj.mosuljournals.com/article_43312_193f27e2c8d68987ee5a5121782dfad8.pdf} }