@article { author = {M. Sh. Ibrahim, Z. and Dr. Kh. A. Zakaria, Prof.}, title = {Effect of Some Variables in Heat of Hydration in concrete}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {1-11}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72710}, abstract = {In this research, the effects of some parameters on the heat of hydration for two concrete mixes have been studied. The mixes are with and without 15% micro silica as a cement weight replacement designated (M2) and (M1) respectively, and Three concrete mixes by weight namely, (1:2:4 , 1:1.5:3 , and 1:1:2) at uniform consistency that is a constant slump of (75-100 mm) for both(M1) and (M2), and Two curing methods, moist and air cured, While the internal temperature for the specimens was measured for (28) days : at the 1st two days at intervals of half an hour then at intervals of (3 hrs) for the 3rd and 4th day, while at intervals of (6 hrs) until (28) days. The results of the research proved that the heat of hydration was higher at the 1st day than that at the 2nd day, fluctuating during the 1st (48 hrs) . The fluctuation reduces gradually to a steady rate at later ages, While the heat of hydration for all mixes and at all ages (except the 1st day) was higher for air cured specimens than that moist cured for same condition, As the cement content increased the heat of hydration (for mixes M1) increased accordingly and also the addition of silica lowered the internal concrete temperature for M1 mixes (at high and moderate cement contents) in opposite of few cement contents.}, keywords = {}, title_ar = {تأثير بعض المتغيرات في حرارة تميؤ الخرسانة_ عربي}, abstract_ar = {الخلاصةأ تم في هذا البحث دراسة تأثير بعض المتغيرات في حرارة التميؤ لنوعين من الخلطات الخرسانية، الأول خرسانة اعتيادية (M1) و الثاني (M2) خرسانة تحوي غبار السليكا بنسبة (15 %) كتعويض عن وزن الاسمنت، و ثلاثة أنواع من نسب الخلط الوزنية لكل خلطة (M1) و (M2) و هي (1:2:4, 1:1.5:3, 1:1:2) و بهطول ثابت لجميع الخلطات (75–100mm)، و طريقتان للمعالجة غمر بالماء و الأخرى تعريض للهواء (بدون رش بالماء)، أما الحرارة الداخلية للنماذج فقد تم قياسها على مدى (28) يوما، في أول يومين من المعالجة قيست الحرارة كل نصف ساعة ، ثم كل ثلاث ساعات لليوم الثالث و الرابع ، ثم كل ست ساعات إلى (28) يوما.أثبتت نتائج البحث أن حرارة التميؤ لليوم الأول أكثر من الحرارة الناتجة في اليوم الثاني، و هي متذبذبة خلال الساعات الثماني و الأربعين الأولى ، ثم بعد ذلك يقل التذبذب تدريجيا و تستقر الحرارة في الأعمار المتقدمة بشكل واضح، و كانت حرارة التميؤ لكافة الخلطات و الأعمار (عدا اليوم الأول) ترتفع في النماذج الخرسانية المعالجة في الهواء أكثر من تلك المعالجة قياسياً بغمرها بالماء و بنفس الشروط ، و بزيادة كمية محتوى الاسمنت تزداد حرارة التميؤ بالنسبة لخلطات (M1) و كذلك قللت إضافة السليكا درجة الحرارة الداخلية عن خلطات (M1) للخلطات غنية و متوسطة محتوى الاسمنت خلافا للخلطات ذات محتوى الاسمنت القليل.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72710.html}, eprint = {https://rengj.mosuljournals.com/article_72710_a8edce61a4b973dabddca7949d873fab.pdf} } @article { author = {Hussain H. Ahmad, Dr. and A. Yousif, Anwar}, title = {Comparison between a Heat Pipe and a Thermosyphon Performance with Variable Evaporator Length_ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {1-12}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72814}, abstract = {Abstract Heat pipes and two phase thermosyphons are heat transfer devices whose operating principles are based on the evaporation/condensation of a working fluid using the capillary pumping forces (in the case of heat pipe) and gravity forces (in the case of two phase thermosyphons) to ensure the fluid circulation. The two systems were designed and constructed to investigate the performance and the affecting parameters, using ethanol as a working fluid. The affecting parameters which were studied are power input (200≤Q≤700) W, working fluid filling ratios (35% and 85%) and aspect ratio, the ratio of evaporator length to inner diameter, (4.0, 7.8 and11.5) . The experimental results showed that the best performance of heat pipe obtained at aspect ratio (7.8) and (85%) filling ratio at (500) W where the maximum heat transfer coefficient was (9950) W/m2.oC, while for the two phase thermosyphon the best performance was obtained at aspect ratio (4.0) for (35%) filling ratio and power input (600) W with maximum heat transfer coefficient equals to(4590) W/m2.oC. The overall comparison between the two systems showed that the performance of the heat pipe is better than that of the two phase thermosyphon. The experimental results of heat pipe was compared with theoretical and empirical correlations showing reasonable agreement especially with immura with percent 70%. KEY WORDS: heat pipe, two phase thermosyphon, aspect ratio, filling ratio}, keywords = {KEY WORDS,two phase thermosyphon,aspect ratio,filling ratio}, title_ar = { مقارنة بين أداء أنبوب حراري وسيفون حراري مع مبخر متغير الطول}, abstract_ar = {الخلاصةالأنبوب الحراري والثرموسيفون الحراري ثنائي الطور هي أجهزة نقل حرارة تعتمد مبادئ تشغيلها على تبخر وتكثف المائع التشغيلي وذلك بالاعتماد على قوى الخاصية الشعرية في حالة الأنبوب الحراري والجاذبية في حالة الثرموسيفون الحراري ثنائي الطور لتدوير المائع التشغيلي. المنظومتان تم تصميمهما و تصنيعهما لتحري الكفاءة والعوامل المؤثرة وباستخدام الأيثانول كسائل تشغيلي. العوامل المؤثرة التي تم دراستها هي: القدرة المجهزة200≤Q≤700) W) ،نسبة مائع التشغيل ( 35%و 85%) والنسبة الباعية، وهي نسبة طول المبخر إلى القطر الداخلي، (4.0, 7.8, 11.5). النتائج العملية أظهرت أن أعلى كفاءة للأنبوب الحراري كانت عند النسبة الباعية (7.8) ونسبة مائع التشغيل (85%) عندما كانت القدرة المجهزة500) W) حيث كان أعلى معامل لانتقال الحرارة هو9950) W/m2.oC) بينما بالنسبة للثرموسيفون الحراري ثنائي الطور فان أعلى كفاءة كانت عند النسبة الباعية (4.0) ونسبة مائع التشغيل (35%) و القدرة المجهزة هي600) W) حيث كان أعلى معامل لانتقال الحرارة يساوي(4590) W/m2.oC. المقارنة العامة بين المنظومتين أظهرت أن الأنبوب الحراري كان أعلى كفاءة من الثرموسيفون الحراري ثنائي الطور. النتائج العملية لكلا المنظومتين تم مقارنتها مع علاقات نظرية وتجريبية و أظهرت المقارنة أن التوافق كان بمقدار70%.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72814.html}, eprint = {https://rengj.mosuljournals.com/article_72814_796eae2335eb86eb17aa466cc694f58a.pdf} } @article { author = {Bayar J. Al-Sulayfani, Dr. and Abd-Ullah Aziz, Islam}, title = { Behavior Of Composite Beams (Steel-Concrete) Strengthened By (CFRP) Sheets Under Repeated Loading}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {12-26}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72723}, abstract = {Present study aims mainly to conduct the behavior of composite beams strengthened with carbon fiber reinforced polymers (CFRP) as they subjected to repeated loads. It investigates the enhancement of load capacity up to failure and the reduction in transverse deflection at the ends of composite beam as affected by (CFRP) strengthening. The following parameters were taken in to consideration in this paper. Location of (CFRP) along the composite beam, Wrapped length effect and effects the Number of (CFRP) layers. From test results it is obvious that (CFRP) is very active in increasing the load capacity by (36%) and reducing the mid span deflection by (56%) in addition to minimizing the slip at beam ends by (98%). Depending on the location, length and number of (CFRP) layers in to account. Key words:- Composite beams, CFRP, Repeated loads and Slip.}, keywords = {Key Words,Composite beams,CFRP,Repeated loads and Slip}, title_ar = {سلوك العتبات المركبة (حديد-خرسانة) المقواة بشرائط (CFRP) تحت تأثير الأحمال التكرارية_عربي}, abstract_ar = {الخلاصةيشمل البحث الحالي دراسة عملية تهدف الى التعرف على سلوك الأعتاب المركبة المقواة بشرائط البوليمر المسلحة بألياف الكاربون (CFRP) عند تعرضها الى حمل تكراري من خلال التعرف على الزيادة الحاصلة في حمل الفشل ونسب النقصان في الأود المقاس في وسط نماذج الأعتاب المركبة بالإضافة الى تأثير التقوية بالشرائح على قيم الإنزلاق المقاسة عند نهايات نماذج الأعتاب المركبة والحاصل بين البلاطة الخرسانية والمقطع الحديدي .تم في هذا البحث الأخذ بنظر الأعتبار التغيير في موقع التغليف بالشرائح بالنسبة للأعتاب المركبة، التغيير بطول التغليف بالشرائح بالنسبة للأعتاب المركبة و تأثير عدد طبقات التغليف بالشرائح على سلوكية الأعتاب المركبة تحت تأثير الحمل المتكرر.وبينت نتائج فحص نماذج الأعتاب المركبة فعالية شرائح ألياف الكاربون في زيادة حمل الفشل وبنسبة وصلت الى(37%) بالمقارنة مع أعتاب السيطرة وتقليل الأود الوسطي بنسبة (56%) بالإضافة الى تقليل الإنزلاق المقاس عند نهايات نماذج الأعتاب المركبة بنسبة(98%) بالإعتماد على موقع وطول التغليف بالإضافة الى عدد طبقات التغليف بشرائح ألياف الكاربون.الكلمات الدالة:الأعتاب المركبة،ألياف الكاربون،الحمل التكراري،الإنزلاق.}, keywords_ar = {الكلمات الدالة,ألياف الكاربون,الحمل التكراري,الإنزلاق}, url = {https://rengj.mosuljournals.com/article_72723.html}, eprint = {https://rengj.mosuljournals.com/article_72723_c46fc99a55267fca2117f36d8ebf7a17.pdf} } @article { author = {Khalid Abdilrazzaq, Tariq}, title = {The effect of circular holes on the natural frequencies of a beam using transverse vibration measurements method _ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {13-24}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72817}, abstract = {Abstract Defects influence in a negative way the service life of the structures. Thus, defect detection has been a considerable effort in order to eliminate this effect . In this study, the dynamical behavior of a cantilever beam, with different size of a hole, at different distances from the fixed end-for each case- have been measured, evaluated and compared with that of intact beam. It has been shown that the hole may be considered as a defect in most cases, which leads-in general- to decrease the stiffness, according to its size and place, hence affects the dynamic properties i.e., the natural frequencies and the mode shapes. A simulation process for the modal analysis using ANSYS program(release 12.1) is done in order to compare the results. In addition to that, a theoretical analysis is also done. The experimental results of the intact beam were compared with both the ANSYS program and the theoretical results. They showed an acceptable agreement between the three methods. Keywords: transverse vibration, fault detection, beam crack, beam defect, beam vibration.}, keywords = {KEYWORDS,fault detection,beam crack,beam defect,beam vibration}, title_ar = {تأثير الثقوب المستديرة على الترددات الطبيعية لعتبة باستخدام طريقة قياس الاهتزاز العرضي}, abstract_ar = {الخلاصةطالما كان تأثير العيوب سلبيا على الحياة العملية للهياكل. ومن اجل ذلك فأن عملية اكتشاف العيوب قد بذلت لها جهود عظيمة من اجل تقليل إضرارها. تم في هذه الدراسة قياس وتقييم حالات السلوك الديناميكي لعتبة كابولية تحوي على ثقب متغير الحجم, وعلى مسافات مختلفة من جهة التثبيت لكل حالة وتم مقارنتها مع أخرى سليمة وقد أظهرت الدراسة أن وجود الثقب في اغلب الأحيان يعتبر عيب يؤدي-على العموم- إلى تقليل جسوءة العتبة وحسب موقعه وحجمه وبالتالي يؤثر على الخواص الديناميكية سلبا (أو إيجابا أحيانا ) من حيث تغيير الترددات الطبيعية ونسق الاهتزاز. كذلك فقد تم احتساب الترددات الثلاث الأولى نظريا, بالإضافة إلى إجراء عملية محاكاة للتجربة باستخدام برنامج انسز (الإصدار 12.1) من اجل مقارنة النتائج . وهكذا فقد تم مقارنة نتائج الحالة السليمة مع نتائج الطريقتين :النظرية, والمستخلصة من برنامج الانسز. حيث أظهرت النتائج أن هناك تطابقا مقبولا إلى حد كبير(يصل إلى 98.2% في الحالة السليمة) بين الطرق الثلاثة.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72817.html}, eprint = {https://rengj.mosuljournals.com/article_72817_0959173df95a34e3347ea0681a415a6c.pdf} } @article { author = {Dahaam Younis, Alaa}, title = {The effect of using Non-Uniform Blank Holder Force in Deep Drawing process on the thickness distribution along the cup_ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {25-31}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72818}, abstract = {Abstract In this paper, a new concept of blank holder in deep drawing is presented. The aim of this study is to predict the wrinkling and thinning (necking) failure through the study of the effect of using constant, variable and non-uniform blank holder force(BHF) between the blank and blank holder on the thickness distribution along the cup (wall, base and nose). Numerical modeling were carried out on various values of blank holder force (BHF) (i.e., Constant-Uniform, Variable-Uniform, Constant Non-Uniform and Variable Non-Uniform). The simulation results shows that the best value of blank holder force were achieved at Variable Non-Uniform type; which gives the smallest difference between maximum and minimum thickness distribution along the cup. Key wards: ANSYS 11, Deep Drawing, Blank holder force}, keywords = {Key wards,Deep Drawing,Blank holder force}, title_ar = {تأثير استخدام قوة مثبت الغفل الغير منتظمة التوزيع في عملية السحب العميق على توزيع السمك على طول الكأس}, abstract_ar = {قي هذا البحث تم دراسة مفهوم جديد لمثبت الغفل في عملية السحب العميق. الهدف من هذا الدراسة هو التوقع للفشل نتيجة التجعد والتنحيف (التعنق) من خلال دراسة تأثير استخدام قوة مثبت الغفل عامل متغير, حيث تم أخذها (ثابتة ومنتظمة، متغيرة ومنتظمة، ثابتة وغير منتظمة التوزيع على طول الغفل ومتغيرة وغير منتظمة التوزيع على طول الغفل) بين الغفل ومثبت الغفل على توزيع السمك على طول الكأس (الجدار, القاعدة والحافة). تم استخدام دراسة رقمية لقيم متغيرة من قوة مثبت الغفل, حيث تمت المحاكاة باستخدام برنامج هندسي واستخراج النتائج, وقد بينت النتائج إن أفضل توزيع للسمك على طول الكأس هو عند استخدام قوة مثبت الغفل المتغيرة والغير منتظمة التوزيع على طول الغفل.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72818.html}, eprint = {https://rengj.mosuljournals.com/article_72818_69689960fe1f69025e8ccff8437f0dcd.pdf} } @article { author = {salim T. Yousif, Dr. and Shams-aldeen, hisaan}, title = {Mechanical Properties of High Strength Steel Fiber Reinforced Concrete}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {27-39}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72717}, abstract = {Abstract In this research, five concrete mixes were prepared, made samples for compressive, Splitting, bending and modulus of elasticity test have been use five of silica fume percentages and three of steel fiber percentages. According to results of this study, addition of steel fiber cause increase in compressive strength, splitting strength, bending strength, modulus of elasticity, and increase the angle of stress-strain curve. Addition of silica fume cause increase in compressive strength, splitting strength, modulus of elasticity, increase the angle of stress-strain curve while cause decreasing in bending strength. The higher compressive strength percentage was (32%) as compared to reference sample prepared at ninety days with silica fume percentage (5%) and steel fiber (0.5%), The higher percentage for splitting strength was (42%) while the highest percentage for modulus of rupture (33%), The highest ratio for modulus of elasticity (27%). Keywords: High strength concrete, Steel fibers, Silica fume, mechanical properties}, keywords = {KEYWORDS,Steel Fibers,Silica fume,mechanical properties}, title_ar = { الخصائص الميكانيكية للخرسانة عالية المقاومة المسلحة بالالياف الفولاذية _ عربي}, abstract_ar = {الخلاصة في هذا البحث تم عمل خمس مزجات خرسانية و اعداد نماذج خرسانية لفحوصات الانضغاط و الشد الانشطاري و معامل المرونة و منحني الاجهاد و الانفعال و الانثناء، تم استخدام خمس نسب من غبار السليكا و ثلاث نسب من الالياف الفولاذية. إنَّ أعلى نسبة زيادة لمقاومة الانضغاط كانت (%32) نسبة الى المزجة المرجعية و بعمر تسعين يوماً عند نسبة غبار السليكا %5 ولنسبة الياف فولاذية %0.5، بالنسبة لمقاومة الشد الانشطاري اعلى نسبة زيادة هي (%42)، في حين أن اعلى نسبة زيادة لمقاومة الانثناء بلغت (%33)، كما أن أعلى نسبة زيادة لمعامل المرونة كانت (%27). و بناء على نتائج الدراسة تم التوصل الى ان اضافة الالياف الفولاذية تؤدي الى زيادة في مقاومة انضغاط الخرسانة و مقاومة الشد الانشطاري و مقاومة الانثناء و معامل المرونة و زيادة ميل منحني الاجهاد و الانفعال و استمرار المنحني لمسافة أطول، تسبب اضافة غبار السليكا الى زيادة ملحوظة في مقاومة انضغاط الخرسانة و مقاومة الشد الانشطاري و معامل المرونة و زيادة ميل منحني الاجهاد و الانفعال، بينما تقلل من مقاومة الانثناء. الكلمات الدالة: خرسانة عالية المقاومة، الالياف الفولاذية، غبار السليكا، الخصائص الميكانيكية}, keywords_ar = {الكلمات الدالة,الالياف الفولاذية,غبار السليكا,الخصائص الميكانيكية}, url = {https://rengj.mosuljournals.com/article_72717.html}, eprint = {https://rengj.mosuljournals.com/article_72717_ae905c9684ba5e8051a7bce0baf238fc.pdf} } @article { author = {F. AL Kababjie, Prof.Dr. M. and H. Hamdon, W.}, title = {Performance Evaluation study of Hybrid Generation System (Microhydro + Diesel) in Iraqi Remote Rural Electrification_ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {32-41}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72823}, abstract = {Abstract This work highlights the benefits and advantages of using Micro Hydro Power Plants (MHPP) in electrification the rural areas, which they are remote from the electric grid and locate beside the river. In these areas Electrical Energy is generated, if any, by diesel generators. This work presents the Performance evaluation and feasibility study as well as environmental effect of adding a Micro Hydro electrical generation unit to two diesel generators used for electrification an Iraqi remote village. Homer software from National Renewable Energy Laboratory (NREL) – USA is used to simulate the system to obtain the optimum hybrid power system configuration. The results of simulation show that the hybrid power system can reduce the cost of electric power unit (kilowatt / hour) as well as reducing the level of air pollution and noise compared to the stand alone diesel system. Index Terms: Hybrid Generation System, Micro-hydropower, HOMER, Renewable energies, Rural electrification, Environmental effects.}, keywords = {Index Terms,Micro,Hydropower,HOMER,Renewable energies,Rural electrification,Environmental Effects}, title_ar = {دراسة تقييم أداء نظام توليد هجين معتمد على وحدة توليد مايكروكهرومائية ومولدة ديزل في كهربة منطقة ريفية عراقية نائية بعيدة عن الشبكة الكهربائية}, abstract_ar = {الخلاصةيبرز هذا البحث الفوائد والمزايا من استخدام مصادر الطاقات الجديدة والمتجددة المتمثلة بوحدات التوليد المايكروكهرومائية في كهربة المناطق الريفية النائية عن الشبكة الكهربائية والقريبة من مجرى النهر. يتم توليد الطاقة الكهربائية في هذه المناطق إن وجدت عن طريق مولدات الديزل. تم في هذا البحث تقييم أداء ودراسة الجدوى الاقتصادية والبيئية من إضافة وحدة توليد مايكروكهرومائية إلى مولدتي ديزل مستخدمة في كهربة إحدى القرى العراقية النائية, وقد استخدم التمثيل ببرنامج هومر (Homer) , وهو برنامج حاسوبي صادر عن المختبر الوطني للطاقة المتجددة في الولايات المتحدة الأميركية يستخدم لتمثيل نظم الطاقة الهجينة والتي تشمل مزيجا من الوقود الاحفوري ومصادر الطاقة المتجددة لتحديد التكوين الأكثر فعالية من حيث التكلفة لكل نظام. أظهرت نتائج التمثيل تقليل كلفة توليد وحدة القدرة الكهربائية (kilowatt/hour) فضلاً عن تقليل مستوى التلوث الجوي والضوضاء عند استخدام وحدة توليد مايكروكهرومائية مع منظومة الديزل مقارنة باستخدام منظومة الديزل لوحدها.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72823.html}, eprint = {https://rengj.mosuljournals.com/article_72823_f48479e7e58bd7057981ebbb62d8430f.pdf} } @article { author = {Sami Majeed, Samer}, title = { Modulus of Rupture of Fully and Partially Reinforced Concrete Beams With Polypropylene Fibers}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {40-51}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72714}, abstract = {Abstract: - In this research an experimental study was conducted to explore some mechanical properties such as compressive strength and splitting tensile strength and modulus of elasticity of concrete mix with weighted mixed portions (1 : 1.5 : 2 / 0.35) reinforced with polypropylene fibers by (0.25%, 0.50%, 0.75%, 1.0%, 1.25%) as volume percentage comparing with normal concrete. Research also contain testing modulus of rupture and maximum deflection of polypropylene concrete beams with dimensions (100×100×500) mm with the same volume percentage and concrete beams with half depth fibrous concrete and the other half normal concrete and comparing with the modulus of rupture and maximum deflection of normal concrete beams. Keywords: Compressive and Tensile strength, Deflection in beams, Modulus of elasticity, Modulus of rupture, Polypropylene fiber.}, keywords = {KEYWORDS,Deflection in beams,Modulus of elasticity,modulus of rupture,Polypropylene fiber}, title_ar = {معاير الكسر للعتبات الخرسانية المسلحة كليا ًوجزئيا ًبألياف البولي بروبلين_ عربي}, abstract_ar = {الخلاصة :-إشتمل البحث على دراسة عملية لبعض الخصائص الميكانيكية التي تضمنت مقاومة الإنضغاط ومقاومة الشد الإنشطاري ومعامل المرونة لمزجة خرسانية بنسب مزج وزنية (1 : 1.5 : 2 / 0.35) مدعمة بألياف البولي بروبلين بنسب حجمية ((0.25%, 0.50%, 0.75%, 1.0,%, 1.25% ومقارنتها مع الخرسانة الإعتيادية. كما تضمن البحث فحص معاير الكسر وأقصى إنحراف لعتبات خرسانية بأبعاد (100×100×500) ملم مدعمة بألياف البولي بروبلين بنفس النسب الحجمية المذكورة ولعتبات بنصف عمق خرسانة ليفية والنصف الآخر خرسانة إعتيادية ومقارنته مع معاير الكسر وأقصى هبوط لعتبات خرسانية إعتيادية .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72714.html}, eprint = {https://rengj.mosuljournals.com/article_72714_9e1f7e59ec1eac7a5f2f98acf32a0899.pdf} } @article { author = {M. J. Mohammed, Dr. and M. Ahmad, B. and K. M. Quboa, Dr.}, title = {UWB MB-OFDM 4-Parallel Radix2 FFT Performance Analysis_ ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {41-53}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72851}, abstract = {Abstract The Ultra Wide-Band Multi Band-Orthogonal Frequency Division Multiplexing (UWBMB-OFDM) systemis a low power (– 41.3 dBm/MHz); short-range (less than 10 m); high speed (53.3 - 480 Mbps) wireless technology with spectral band widthfrom 3.1GHz to 10.6 GHz allocated by Federal Communications Commission (FCC) according to IEEE 802.15.3a standard. The UWB spectrum is divided into 14 subbands, each with 528 MHz bandwidth . Each OFDM symbol is transmitted / received a cross each subband using a single 128-point radix2 IFFT/FFT. In this paper a simulation software is written using Matlab version 10 to evaluate the Bit Error Rate (BER) of the system using the traditional 128-point IFFT/FFT algorithm, and the proposed 4-parallel 32-point radix2 IFFT/FFT algorithm. It has been shown that a time saving is 28.7 % , and that the BER is better off 5dB using the proposed method as compared to traditional method.}, keywords = {}, title_ar = {دراسة أداء نظام الطيف الواسع المتعدد الحزم باستخدام أربعة محولات فورير رقمية متوازية}, abstract_ar = {الخلاصةإن نظام الحزمة العريضة جداً للحزم المتعددة للترددات المقسمة المتعامدة (UWB MB-OFDM) هو ذات قدرة منخفضة (– 41.3 dBm/MHz); لمسافات البثالقصيرة (أقل من 10م); وبسرع عالية (53.3Mbps - 480 Mbps) يعمل بعرض حزمة من 3.1 GHzإلى 10.6 GHzالمحددة من قبل لجنة الاتصالات الاتحادية (FCC) حسب الأنموذج القياسي IEEE 802.15.3a . يُقسم طيف الحزمة UWB إلى 14 حزمة فرعية كل حزمة بعرض 528 MHz . يرسل يستلم رمز OFDM عبر كل حزمة فرعية بوساطة كتلة واحدة من محول فورير السريع (IFFT/FFT) ذات الحجم 128.في هذا البحث تمّ إجراء محاكاة النظام باستخدام برنامج Matlabالنسخة 10لإيجاد قيم معدل خطأ البت (BER) للنظام التقليدي باستخدام كتلة واحدة من محول فورير السريع بحجم 128 وللنظام المقترح باستخدام أربع كثل متوازية من محول فورير السريع بحجم 32, وتمّ توضيح إن نسبة الوقت المكتسب هي 28.7 % و BER أفضل بحدود 5dB باستخدام الطريقة المقترحة مقارنة مع الطريقة التقليدية.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72851.html}, eprint = {https://rengj.mosuljournals.com/article_72851_6f745744d5018d17095be93a864a8fcd.pdf} } @article { author = {}, title = {Pressure effect on wetting pattern in layered soil for subsurface point source}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {52-63}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72799}, abstract = {Abstract Laboratory experiments were carried out to investigate the effect of operating pressure on wetting pattern in layered soil for subsurface point water source. This study helps to determine a suitable operating pressure and appropriate spacing between emitters and drip lateral pipes . The layered soil profiles were prepared using two types of soil (clay and loam) in two combinations (clay over loam and loam over clay) . Three operation pressures (4.99, 9.99 and 16.14, m) with a nominal dripper discharge rate (2 l/hr) were used . The experimental results showed that positive back pressure around dripper outlet develops, when the water application rate is larger than the soil infiltration capacity , and the actual dripper discharges were less than the rated dripper discharges by about (10%-28%) due to back pressure effect . Furthermore, it has been observed that water start rising up to the soil surface (Chimney Effect) when the operating pressure is (16.14m) for the loam over clay soil profile, which occurs when water application rate exceeds the soil capability to spread the water. It is found that the total wetted area for both layers was not affected by the operation pressure for the same volume of applied water . In the relationship of the wetting advance (a tb) , it is found that , the constant (b) is not effected by operation pressure while the constant (a) increased with increased operation pressure .}, keywords = {}, title_ar = {تأثير الضغط على نمط الابتلال في تربة طباقية النسجة لمصدر تنقيط مدفون تحت سطح التربة_ عربي}, abstract_ar = {الملخص تم في هذا البحث إجراء تجارب مختبرية لدراسة تأثير الضغط التشغيلي على نمط الابتلال لتربة طباقية لمصدر منقط مدفون تحت سطح التربة ، حيث تساعد هذه الدراسة تحديد الضغط التشغيلي المناسب لمنظومة الري وفي تحديد الفاصلة المناسبة بين المنقطات وبين أنابيب التنقيط . تم إجراء الدراسة باستخدام نوعين من الترب (طينية ومزيجية) وعند ثلاث ضغوط تشغيلية (4.99 و 9.99 و 16.14 م) وتصريف منقط اسمي (2 لتر/ساعة) . وقد تم إعداد مقاطع الترب بتعاقبين مختلفين لطبقتي التربة (طينية فوق مزيجية ومزيجية فوق طينية) . أظهرت الدراسة بان هنالك ضغطاً عكسياً موجباً يتولد في التربة نتيجة إضافة الماء بمعدل عالي يفوق سعة التربة لإرتشاح الماء ، وأن قيم تصريف المنقط الفعلية كانت اقل من قيم تصريف المنقط المستحصلة من معادلة خصائص منحني المنقط بحدود (10%-28%) وذلك بسبب تأثير الضغط العكسي . وقد رُصِدَ خروج الماء إلى سطح التربة بما يعرف (Chimney Effect) عند الضغط التشغيلي العالي (16.14 م) وعند وضع التربة المزيجية فوق الطينية، نتيجة زيادة معدل إضافة الماء عند ذلك الضغط التشغيلي بصورة تفوق قابلية التربة على نشره خلالها . وقد وجد أن المساحة الكلية للابتلال لم تتأثر بشكل ملحوظ بقيمة الضغط التشغيلي وذلك لنفس كمية الارتشاح التراكمية . وقد لوحظ في علاقة تقدم جبهة الابتلال (a tb) أن الثابت b لا يتأثر بزيادة الضغط التشغيلي بينما تزداد قيمة الثابت a مع تلك الزيادة .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72799.html}, eprint = {https://rengj.mosuljournals.com/article_72799_40032472f0c771a4ec558a4c609f3e20.pdf} } @article { author = {R. Hamdy, Yehia and Sami A. Mawjoud, Dr.}, title = {Assessment of Uplink Time Difference Of Arrival (U-TDOA) Position Location Method in Urban Area and Highway in Mosul City_ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {54-65}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72854}, abstract = {Abstract The aim of this paper is the assessment of the performance of U-TDOA Position Location (PL) method on a UMTS cellular system in Mosul city, Iraq. The study area is a (3×3 km) which covers the University of Mosul campus. Simulation is used to study and evaluate the performance of U-TDOA PL method in urban area and on a highway inside the city. The effect of terrain, multipath, signal to noise ratio (SNR), Geometric Dilution Of Precision (GDOP), shadowing and the configuration of base stations on the positioning accuracy are investigated. The study is conducted on a real coordinates with the distribution of UMTS BSs as the same existing 2.5 Generation Enhanced Data rates for GSM Evolution (EDGE)Asiacell operator. Keywords: U-TDOA, Position Location, UMTS.}, keywords = {KEYWORDS,TDOA,Position Location,UMTS}, title_ar = {تقييم طريقة تحديد المواقع الفرق في زمن الوصول للاتصال الصاعد (U-TDOA) على منطقة مدنية مزدحمة وطريق سريع داخل مدينة الموصل}, abstract_ar = {الخلاصةالهدف من هذا البحث هو تقييم اداء طريقة تحديد المواقع (الفرق في زمن الوصول للاتصال الصاعد (U-TDOA)) في شبكة الهاتف الخلوي لنظام الجيل الثالث (UMTS) داخل مدينة الموصل, العراق. المنطقة التي تمت الدراسة عليها هي منطقة بمساحة (3 × 3 كيلو متر) والتي تغطي حرم جامعة الموصل. تم استخدام المحاكاة باستخدام الحاسوب لدراسة وتقييم اداء طريقة تحديد المواقع (U-TDOA) على منطقة مدنية مزدحمة وكذلك على طريق سريع داخل المدينة. تم دراسة كل من (التضاريس وتعدد المسارات ونسبة الاشارة الى الضوضاء والتقليل الهندسي للدقة والتظليل وموقع المحطات الاساسية) على دقة تحديد الموقع. تم اجراء الدراسة على احداثيات حقيقية وتم توزيع المحطات الاساسية لنظام (UMTS) على نفس مواقع المحطات الاساسية لنظام الجيل الثاني المحسن (EDGE) لشركة اسياسيل.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72854.html}, eprint = {https://rengj.mosuljournals.com/article_72854_159940f3e1a88831270a301ed1e30469.pdf} } @article { author = {Azhor Thanoon, Ahmed}, title = {Gross Irrigation Water Requirement for Durum Wheat Crop (Sham 3) At Mosul Area In Season 2009/2010}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {64-72}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72800}, abstract = {Abstract This study aims to determine the gross irrigation water requirement GIWR for durum wheat crop (Sham3) using climate , crop, and soil in Mosul area . The experiment was carried out in the field of the technical institute of Mosul for the cultivation durum wheat crop cv.Sham3 in season 2009/2010. The consumptive water use was determined by multiplied the calculated reference crop evapotranspiration using Penman-Monteith equation based on climatological data for Mosul station which considered the nearest to the experiment , by a crop coefficient depended on the growth of stages ( initial , development , mid , and end stage) . The GIWR was 175 mm.season-1 and determined based on the effective rainfall, consumptive water use , change in soil water storage in root zone , and efficiency of irrigation . Four irrigation treatments were used 100% , 50% , 25% from GIWR , and without irrigation , only rainfall .The results showed that the crop properties such as the grain yield increases with irrigated in full GIWR and reached to 5.5 t/ha ,While it decreases by 20% with irrigated in 50% from GIWR . Keywords: Irrigation water requirement, Penman-Monteith, Durum wheat, Mosul.}, keywords = {KEYWORDS,Penman,Monteith,Durum wheat,Mosul}, title_ar = {الاحتياجات المائية لمحصول الحنطة القاسية (شام3) في منطقة الموصل للموسم _ عربي}, abstract_ar = {المستخلص تهدف هذه الدراسة إلى حساب الاحتياجات المائية (اجمالي احتياجات ماء الري GIWR) لمحصول الحنطة القاسية صنف شام3 باستخدام بيانات المناخ والمحصول والتربة في منطقة الموصل . نفذت تجربة حقلية بالمعهد التقني الموصل لزراعة محصول الحنطة القاسية صنف شام3 خلال 2009/ 2010.تم حساب الاستهلاك المائي للمحصول من ضرب قيمة التبخر-نتح المرجعي المحسوب بمعادلة بنمان-مونتيث من البيانات المناخية لمحطة الموصل الأقرب إلى منطقة التجربة ، بقيمة معامل المحصول الذي يعتمد على مراحل النمو وهي البداية ، والمتطورة ، والوسطية ، والنهائية .تم حساب الاحتياجات المائية GIWR والتي كانت 175 ملم.موسم-1 خلال الموسم بالاعتماد على كمية الأمطار الفعالة والاستهلاك المائي للمحصول والتغير في الماء المخزون عند المنطقة الجذرية وكفاءة الري . تم استخدام أربع معاملات أرواء وهي سقي المحصول بكامل100 % وبنصف 50% وربع 25% من إجمالي احتياجه من ماء الري وبدون إضافة ري أمطار فقط . وأظهرت النتائج بان صفات الحاصل كإنتاج الحبوب تزداد مع إعطاء كامل احتياجه المائي حيث وصل الى 5.5 طن هكتار-1، بينما انخفض الإنتاج بنسبة 20% عند استخدام الري التكميلي لتزويد 50% من احتياجه المائي .الكلمات الدالة : احتياجات ماء الري ، بنمان-مونتيث ، الحنطة القاسية ، الموصل .}, keywords_ar = {الكلمات الدالة,بنمان,مونتيث,الحنطة القاسية,الموصل}, url = {https://rengj.mosuljournals.com/article_72800.html}, eprint = {https://rengj.mosuljournals.com/article_72800_ddee03393c7f46307a3c48ebb6ad2daa.pdf} } @article { author = {Jassim M. Abdul-Jabbar, Dr. and M. Jasim, Abdulhamed}, title = {Design and MultiPlierless Realization of ECG- Based Gaussian Wavelet Filter with Lattice Structures_ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {66-77}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72855}, abstract = {Abstract In this paper, the Gaussian function is selected as a mother wavelet function and utilized in the design of some corresponding filter banks. With a 1st derivation of the Gaussian function, a similar shape to QRS complex part of the ECG is achieved.It can be used for QRS feature extraction.Using thesymmetry property of the mother wavelet function, the designed FIR wavelet filter banks can be realized in highly-efficient lattice structures which are easy to implement. The resulting lattice structures reduces the number of filter banks coefficients and this reduces, in turn the number of multiplications and improves the filter banks efficiencies as it reduces the number of computations performed. Hardwarely, this leads to less-complex implementations. The resulting quantized multiplier values also lead to a multiplierless realization for such wavelet filter banks. Keywords: ECG,Wavelet and scaling functions, Filter banks, Lattice structures, Multiplierless realization.}, keywords = {KEYWORDS,Wavelet and scaling functions,Filter Banks,Lattice structures,Multiplierless realization}, title_ar = {التصميم والتحقيق بلا مضارب لمرشح مويجي نوع دالة كاوسبإعتماد إشارة ECGوإستخدام الهياكل المتشابكة}, abstract_ar = {الخلاصةفي هذا البحث، تم إختيار دالة كاوس كدالة أم مويجيةّوإستغلالها لتصميم بعض أجراف مرشحات مقابلة. وبمجرد أن تجرى عملية إشتقاق من المرتبة الاولى لدالة كاوس، سنحصل على شكل مماثل لجزء QRS المعقّد في إشارة ECG، والتي يمكن أن تستعمل لإستخلاص ميزّات QRS.وإعتماداً علىخاصية التناظر لهذه الدالة المويجة الأم، فإن المرشحات المصممة يمكن تحقيقها بهياكل متشابكة كفوءة جداً وسهلة البناء.الهياكل المتشابّكة الناتجة تخفّض من عدد معاملات أجراف المرشحاتوهذا بدوره يخفّض عدد المضارب ويحسّن كفاءة أجراف المرشحات حيث أنه يخفّض عددالحساباتالمؤداة.وعلى صعيد المكونات المادية فإن هذا سيؤدّي إلى بناءات أقل تعقيّداً.إن قيم المضارب المكممة الناتجةستقود الى تحقيق بلا مضارب لأجراف المرشحات المويجية تلك.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72855.html}, eprint = {https://rengj.mosuljournals.com/article_72855_27e580e5ac04be4f780712593cadfa1d.pdf} } @article { author = {lecture. Hameed A, Assist and lecture. Hameed A, Assist}, title = {Optimal Neuro-Fuzzy D.C. Motor Speed Control}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {73-86}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72801}, abstract = {Abstract This work deals with investigating of d.c. motor speed controlled by a buck-boost converter. Open loop system is tested. Aneuro-Fuzzy controller with random number and type of membership function is designed to control the speed of the d.c. motor as a closed loop system. Because of the lack of a clear and a known way for selecting the type and number of membership function in case of fuzzy control, An Adaptive Neuro-Fuzzy Inference System which comprises a fuzzy inference structure and neural network learning ability is modified to control the speed of the motor. The technique is used to select the optimal number and the best type of membership function for the fuzzy system. The process is carried out through testing four types of membership functions with different numbers (3,5,…etc) for each type and computing the absolute error for each case comparing their results to choose the smallest among them. Then the chosen root is applied to control the system for the rest time of control. The technique is applied to two loads (motors).}, keywords = {}, title_ar = {المتحكم الأمثل للسيطرة على سرعة محرك التيار المستمر باستخدام الشبكات العصبية المضببة_ عربي}, abstract_ar = {الخلاـصةالعمل الحالي يتناول دراسة سرعة محرك تيار مستمر مسيطر عليه باستخدام المغير الخافض الرافع واختبار نظام الحلقة المفتوحة. محكم الشبكات العصبية المضببة صمم باختيار عشوائي لعدد ونوع الدوال العضوية للتحكم بسرعة محرك التيار المستمر. بسبب عدم وجود طريقة واضحة ومعروفة لاختيار عدد ونوع دوال العضوية في حالة استخدام المحكم المضبب, لقد تم تطوير نظام الاستدلال الضبابي المستند على الشبكات العصبية التكيفية والذي يربط بين بنية الاستدلال الضبابي وقابلية التعلم للشبكات العصبية التكيفية وذلك للسيطرة على سرعة محرك التيار المستمر. التقنية استخدمت لاختيار أحسن عدد وأفضل نوع من دوال العضوية للمنظومة المضببة. العملية تمت من خلال اختيار أربعة أنواع من دوال العضوية وبأعداد مختلفة (7,5,3) لكل نوع ومن ثم حساب الخطأ النسبي لكل حاله ومقارنة النتائج لاختيار الأقل من بينهم. ومن ثم استخدام المسار المختار للسيطرة على سرعة المحرك في ما تبقى من وقت العمل. التقنية المطورة استخدمت للسيطرة على سرعة محركين مختلفين في الخصائص ومتشابهين في النوع. الكلمات الدالة:الشبكات العصبية المضببة , محرك التيار المستمر , السيطرة التكيفية , المغير الخافض الرافع.}, keywords_ar = {الكلمات الدالة,محرك التيار المستمر,السيطرة التكيفية,المغير الخافض الرافع}, url = {https://rengj.mosuljournals.com/article_72801.html}, eprint = {https://rengj.mosuljournals.com/article_72801_9647d947a0065c4d189744676a47e8b6.pdf} } @article { author = {N. Mahmood, Mohammed and SideqThanoon, Hassan}, title = {FlexuralStrength of Reinforced Concrete Slabs Strengthened and Repaired by High StrengthFerrocement at Tension Zone_ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {78-89}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72859}, abstract = {Abstract This paper presents a study of the flexural behavior of strengthened and repaired reinforced concrete slabs by ferrocement. The study includes testing 17 simply supported slabs, which include 2 control slabs, 3 strengthened slabs and 12 repaired slabs. In the strengthenedslabs the effect of number of wire mesh layers of ferrocement on the ultimate load, mid span deflection at ultimate load and intensity of cracks were examined. In the repaired part the slabs were stressed to (70 %) of measured ultimate loadof control slab. The effectsof number of wire mesh layers, ferrocement thickness and the connection method between repaired slabsand ferrocementjacket on the ultimate load, mid span deflection at ultimate load and intensity of cracks were examined. Keywords: Concrete, ferrocement, repair, slab, strengthening}, keywords = {KEYWORDS,ferrocement,Repair,Slab,Strengthening}, title_ar = {مقاومة الانثناء للبلاطات الخرسانية المسلحةالمقواة والمصلحة بغطاء من الفيروسمنت عالي المقاومة في منطقة الشد}, abstract_ar = {يتضمن البحث الحالي دراسة مقاومة الانثناء للبلاطات المقواة والمصلحة باستخدام الفيروسمنت من خلال تقصي ومقارنة نتائج الفحص لسبعة عشر بلاطة, ثلاث منها مقواةبالفيروسمنت، اثنا عشر بلاطة لدراسة فاعلية عملية الإصلاح وبلاطتان تم أخذهما كبلاطات مرجعية. إن المتغيرات التي تمت دراستها في عملية التقوية هي تأثير عدد طبقات المشبكات السلكية، حيث تم استخدام (2, 3 & 4) طبقات من المشبكات السلكية، على الحمل الأقصى والأود المقابل له بالإضافة إلى تأثيرها على كثافة الشقوق، أما في حالة الإصلاح فقد تم تسليط (70 %) من الحمل الأقصى المأخوذ من البلاطات المرجعية على البلاطات المراد إصلاحها ودراسة تأثير كل من عدد طبقات المشبكات السلكية، حيث تم استخدام (2, 3 & 4) طبقات،وسمك الفيروسمنت، تم استخدام فيروسمنت بسمك (2 & 3 cm)، وطريقة ربط الفيروسمنت بالبلاطة،استخدم اسلوب الربط بواسطة البراغي او بواسطة الايبوكسي,على عملية الإصلاح بالفيروسمنت.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72859.html}, eprint = {https://rengj.mosuljournals.com/article_72859_6b3d181569636959d15ef0b9e39e715d.pdf} } @article { author = {Hussain H. Ahmad, Dr. and M. Abd, Hareth}, title = {Performance and Heat Transfer Characteristics in Loop Thermosyphon (An Experimental Study)}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {87-98}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72803}, abstract = {A Loop Thermosyphon has been designed, fabricated and tested to investigate the heat transfer characteristics by two-phase natural convection. The rig was made from copper tubes connected with each other in closed loop including four main parts: vertical evaporator located in the bottom of the device and surrounded by an electrical coil heater as a heat source ,a horizontal condenser located in the upper part of the device cooled by water, vapor rising adiabatic tube and condensate return adiabatic tube. In this research the effect of heat input and filling ratio of the evaporator on the heat transfer coefficient and temperature distribution on the loop surface was verified experimentally using distilled water as working fluid at operating pressure near-atmospheric pressure. The maximum heat transport capability for evaporator was found to be equal to (3424 W/m2 oC). A comparison between the present work results with empirical and theoretical correlations of other researchers showed good agreement.}, keywords = {}, title_ar = {أداء وخواص انتقال الحرارة في سيفون حراري حلقي (دراسة عملية)_عربي}, abstract_ar = {الخلاصةتضمن البحث تصميم وتصنيع جهاز السيفون الحراري الحلقي Loop Thermosyphon)) لإجراء دراسة عملية لخواص انتقال الحرارة بالحمل الحراري الطبيعي ثنائي الطور. يتكون الجهاز من أنابيب نحاسية متصلة مع بعظها ضمن دورة مغلقة ويشتمل على أربعة اجزاء رئيسة: مبخر عمودي يقع في الجزء السفلي من الجهاز محاط بمسخن كهربائي يمثل مصدر الحرارة, ومكثف أفقي يقع في الجزء العلوي من الجهاز ويبرد بالماء وأنبوبين أحدهما لنقل البخار والآخر لنقل المائع المتكثف. تم في هذا البحث التحقق تجريبياً من تأثير تغيير مقدار القدرة الداخلة ونسبة الملء للمبخر على معامل انتقال الحرارة وتوزيع درجات الحرارة على سطح السيفون الحراري الحلقي باستخدام الماء كمائع تشغيل عند ضغط مقارب للضغط الجوي. وقد تم الحصول على أعلى قيمة لمعامل انتقال الحرارة للمبخر بمقدار (3424 W/m2 oC). أظهرت المقارنة بين النتائج العملية للبحث مع نتائج علاقات عملية ونظرية لباحثين آخرين توافقاً جيداً.الكلمات الدالة: انتقال الحرارة, الحمل الحراري ثنائي الطور, السيفون الحراري}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_72803.html}, eprint = {https://rengj.mosuljournals.com/article_72803_2193b7c70a912b3e3b068e34b28c29d8.pdf} } @article { author = {Hassan Ali, Turki and Rashad Shaheen, Bahjat}, title = {Urban micro-climate in the City of Mosul, Iraq (The Effect of Urban Space Characters on Air Temperature) _ENG}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {90-97}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72861}, abstract = {Abstract The proportion of the world's population living in urban areas is constantly increasing. Different urban shapes result different micro-climates. The way cities are planned and build is therefore important for the global energy use. The city of Mosul ( north of Iraq) had witnessed a rapid urbanization during the second half of the last century, adopting the open grid iron system in planning the new residential areas which now exist beside the traditional compact system. This study present result from measurements of Max. air temperature during hot season in (156) points in the traditional paths of the old city (called zuqaqu) and (44) points in the streets of the modern neighborhoods, more over the engineering-physical characteristics of each point had been measured. Using statistical analyzing for determining the impact of each of these characters on the urban micro climate (Max. air temperature).The primary results show that sky view factor has the major impact on air temperature, and that confirm the important role of the urban designers and planners in the urban micro-climate. Key words: urban micro-climate, traditional city, Mosul.}, keywords = {Key Words,Climate,traditional city,Mosul}, title_ar = { المناخ الحضري الموضعي لمدينة الموصل (اثر خصائص الفضاء الحضري في درجة حرارة الهواء)}, abstract_ar = {تتزايد نسبة سكان العالم الذين يعيشون في المناطق الحضرية بشكل مستمر. والأشكال الحضرية المختلفة ينتج عنها مناخات حضرية موضعية مختلفة، لذلك فان طريقة تخطيط وبناء المدن لها اثر كبير على ساكني هذه المدن من حيث راحتهم الحرارية حين يستخدمون فضاءات تلك المدن. مدينة الموصل (شمال العراق) شهدت التحضر السريع خلال النصف الثاني من القرن الماضي، واعتمد النظام الشبكي المفتوح في تخطيط مناطقها السكنية الجديدة والتي تواجدت جنبا الى جنب مع نسيجها التقليدي المتضام. لمعرفة اثر الخصائص الهندسية والفيزياوية للفضاء الحضري على درجة حرارة الهواء عمدت الدراسة الى قياس درجة حرارة الهواء العظمى في (156) نقطة من مسارات المدينة القديمة ذات النسيج الحضري التقليدي في المدينة القديمة (الازقة) و (44) نقطة في شوارع الأحياء الحديثة للمدينة للفترة الأشد حرارة من السنة، فضلا عن تحديد كل من الخصائص الفيزيائية والهندسية لكل نقطة تم قياسها. تم استخدام التحليل الإحصائي لتحديد تأثير كل من هذه الخصائص على المناخ الموضعي (درجة حرارة الهواء). النتائج الأولية أظهرت أن معامل رؤية السماء كان له الأثرالأكبر على درجة حرارة الهواء، والتي تؤكد على الدور الهام للمصممين الحضريين والمخططين للمناطق الحضرية في المناخ الموضعي للمناطق الحضرية.الكلمات الدالة: المناخ الحضري الموضعي، المدينة التقليدية ، مدينة الموصل.}, keywords_ar = {الكلمات الدالة,المدينة التقليدية,مدينة الموصل}, url = {https://rengj.mosuljournals.com/article_72861.html}, eprint = {https://rengj.mosuljournals.com/article_72861_1b4b8c09f787527930cd987ad970faac.pdf} } @article { author = {E. H. Alallaf, Dr. and H. Alsoofe, H. and N.T. Alkymakchy, Dr.}, title = {The impact of design concepts on thinking performance in urban design studio}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {21}, number = {2}, pages = {99-117}, year = {2013}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2013.72808}, abstract = {Design concepts play a crucial role in guiding the mental action during the design task, because they represent the media which support the design goals and strategy, these concepts are vary according to the design circumstance, the type of building and the designer. It is difficult to capture these concepts through the design product in architecture and urban design that due to the difficulty of conceptual perception by the designer and the difficulty of delivering overall conceptual message from architect to others. This problem exacerbate in the students design behavior in architectural study, due to the inadequacy of the experience that they enjoy in the design work, and inappropriate election of the concepts to solve the design problem This research attempts to draw the design action and its change during a design experiment carried out by students in the final stage of architectural study (in urban design studio), to highlight the variation between this action and the change of design concept to indicate preferences elements of this concept by the student in the message delivery to the recipient, and thus his/her success in completing the work. The research tries to measure the thinking performance of the student within eight design sessions, through classifying design concept submitted by him/her and drop it into (Rasmussen) model of thinking performance Finally the research will try to find obstacles in the election of certain types of design concepts in urban design projects on the total thinking production. Keywords: design concepts, architectural education, design thinking, productive thinking}, keywords = {KEYWORDS,architectural education,design thinking,Productive thinking}, title_ar = {اثر المفاهيم التصميمية على الأداء الفكري للطالب في مرسم التصميم الحضري_ عربي}, abstract_ar = {الخلاصةتلعب المفاهيم التصميمية (Design Concepts) دورا مهما في قيادة الفعل الفكري عبر زمن أداء المهمة التصميمية، لأنها تشكل الوسط الذي تتفاعل فيه أهداف المصمم وأرائه، والداعم الأساسي لإستراتيجيته التصميمية، وتختلف هذه المفاهيم باختلاف الفعل التصميمي، فهي تأخذ أشكالا متباينة حسب الظرف التصميمي ومؤثراته وتتغير بتغير نوع المبنى وطبيعة المصمم.وإذا كان من الصعب ملاحظة هذه المفاهيم من خلال النتاج التصميمي في العمارة بشكل عام وفي المشاريع الحضرية بشكل خاص، فان ذلك مرده لصعوبة التقاط المفهوم من قبل الآخرين من ناحية، وصعوبة إيصال مجمل الرسالة المعمارية من قبل المصمم (المرسل) من ناحية أخرى.وتتفاقم تلك المشكلة لدى الطلبة في مراحل الدراسة المعمارية لضعف تجربتهم، وعدم كفاية الخبرة التي يتمتعون بها في انجاز العمل التصميمي، وسوء انتخاب المفاهيم الملائمة والتي تساعد على حل المشكلة التصميمية.تحاول هذه الورقة البحثية رسم صورة الفعل الفكري وتغيره إبان التجربة التصميمية التي يمر بها الطلبة في المرحلة المنتهية من دراسة العمارة (وضمن مرسم التصميم الحضري لديهم على وجه الخصوص) ومعرفة علاقة شكل ذلك الفعل بتغير المفهوم التصميمي، وذلك كمحاولة لتأشير أفضليات عناصر المفهوم المنتخب من قبل الطالب في إيصال الرسالة التصميمية وبالتالي نجاحه في انجاز العمل التصميمي.ولتحقيق ذلك فان البحث يحاول قياس أداء الطالب الفكري ضمن تلك التجربة التي تمتد لثمانية جلسات تصميمية وعلى مدار أربعة أسابيع. وذلك عن طريق تصنيف معطيات المفهوم التصميمي المقدم من قبله ومقارنته مع إسقاطات إنتاجيته الفكرية وفق أنموذج راسمو سين (Rasmussen) للأداء الفكري.يحاول البحث في النهاية استخلاص معوقات انتخاب أنواع معينة من المفاهيم التصميمية في المشاريع الحضرية على مجمل الأداء التصميمي للطالب.الكلمات الدلالية : المفاهيم التصميمية، التعليم المعماري، التفكير التصميمي ، التفكير المنتج}, keywords_ar = {الكلمات الدلالية,التعليم المعماري,التفكير التصميمي,التفكير المنتج}, url = {https://rengj.mosuljournals.com/article_72808.html}, eprint = {https://rengj.mosuljournals.com/article_72808_a7e34ae171fd73b2eff2361643ea5bdc.pdf} }