@article { author = {Akram Abdullah, Ahmed and Hallosh Khidhir, Awad}, title = {The Effect of Mold Rotational Speed on Mechanical Properties of Functionally Graded Polymeric Matrix Composites}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {1-12}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101070}, abstract = {In this research, a functionally graded polymeric matrix composites (FGPMCs) were produced using centrifugal casting method. These composites were fabricated from unsaturated polyester resin as a matrix and reinforced with silicon carbide particles (SiCp) of (106µm) and (6%)bulk volume fraction, using different mold rotational speeds(400,500,600 R.P.M) at room temperature (22Cº).Additional (3) samples of pure polyester were manufactured at the same conditions for comparison purpose .The aim of the present research was to study the effect of mold rotational speed on local values of volume fraction,hardness and Young modulus at specific points along the graded samples. Hardness was measured at these points then graded samples were cut to eight portions .Densityand volume fraction were evaluated,then standard homogenoussamples of constant but different volume fraction were manufactured. Results shows that local values of volume fraction, hardness and Young Modulus decreased in nearby positions of the center of rotation and increased in positions far away from the center of rotation with increasing mold rotational speed.}, keywords = {Functionally graded polymeric composite,Hardness,Modulus of elasticity,mold rotational speed}, title_ar = {تأثير سرعة دوران القالب في الخواص الميكانيكية لمواد متراكبة بوليميرية متدرجة وظيفياً}, abstract_ar = {تم في هذا البحث انتاج مواد متراكبة بوليميرية متدرجة وظيفياً(FGPCs) مادتها الاساس من البولي استر غير المشبع(Unsaturated Polyester Resin) ومعززة بدقائق من كربيد السليكون(SiCp) بكسر حجمي كلي (%6) وحجم حبيبي(106µm) ومصنعة بطريقة الطرد المركزي وبسرعة دورانية مختلفة (400,500,600R.P.M) وبدرجة حرارة الغرفة(22Cº) فضلا عن انتاج ثلاثة نماذج من البولي استر النقي وبالظروف نفسها لغرض المقارنة. تم دراسة تأثير تغير سرعة دوران القالب في القيم الموضعية للكسر الحجمي والصلادة ومعامل المرونة للنماذج المصنعة وفي نقاط محددة على طول كل أنموذج متدرج .تم قياس الصلادة في هذه النقاط ومن ثم تقطيع كل انموذج متدرج الى ثمانية قطع وحساب كثافتها وتحديد كسرها الحجمي وانتاج نماذج متجانسة قياسية ذات مواصفات مناظرة لتلك الخصائص لغرض اختبار الشد .اظهرت نتائج البحث انخفاض القيم الموضعيةللكسرالحجمي والصلادة ومعامل المرونة في المواضع القريبة من مركز دوران القالب وارتفاع هذه القيم في المواضع البعيدة عن مركز دوران قالب الطرد المركزيمع زيادة سرعة دوران القالب.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101070.html}, eprint = {https://rengj.mosuljournals.com/article_101070_056756755b629599fb020677b3653396.pdf} } @article { author = {M. Hassan, Shamil}, title = {Practical Analysis for Studying the Effect of Both Depth and Soil types on the Stresses Generated on the draw-bar During Plowing Process}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {13-19}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101071}, abstract = {A study was conducted for the purpose of determining the stresses generated on the draw-bar as a result of different types of soil and depth produced during plowing process in two different soils. Laboratory analysis was conducted for studying the soil analysis in the department of Civil Engineering University of Mosul. Analysis revealed that there were two different types of soil (clay and mixed). At the same time mechanical properties and basic measurements of draw-bar was carried out. At the same time stress analysis of draw-bar was done using finiteelements program (Ansys releases 14.0 types), to determine the properties during application in different stress analysis parameters where used (x, y, z) and Von Mises in addition to principal stresses and percentage deviation of the direction of the three axes (x, y, z). During practical phrase, installation of strain gauges on draw-bar was done , for two types of soil at different depth level factors using three level (40, 45, 50) cm. The present results revealed that there was a difference in the stress values generated in relation to depth and types of soil.}, keywords = {Soil Test,Stress Analysis,finite element analysis,Draw,bar}, title_ar = {تحليل عملي لدراسة تأثير العمق ونوع التربة على الاجهادات المتولدة على ساق المحراث اثناء عملية الحراثة}, abstract_ar = {اجريت الدراسة لغرض تحليل الاجهادات المتولدة على ساق المحراث عند اختلاف العمق ونوع التربة، وقابلية تحمله للاجهادات المتولدة عليه اثناء عملية الحراثة وفي تربتين مختلفتين.تم اجراء الفحص المختبري للتربة في مختبرات الهندسة المدنية جامعة الموصل وتبين ان نوع التربة الاولى طينية والتربة الثانية مزيجية، وتم التأكد من نوع معدن الساق وهو (High quality steel) والخواص الميكانيكية له ومن ثم تثبيت الابعاد والقياسـات الاساسية لاجزاء الساق، وفي نفس الوقت تم اجراء تحليل الاجهادات المؤثرة على الساق باسـتخدام تقنية العناصر المحددة (Finiteelement technique) نـوع (Ansys Release 14.0) ، وبيان مدى تحمله لحالات مشابهة لظروف العمل الحقلية. اخذت عدد من الاجهادات منها الاجهادات بالمحاور الثلاثة (x, y, z) والاجهاد الاعظم (Von Mises) والاجهادات الرئيسة (Principal stresses) ، اضافة الى نسبة الانحراف باتجاه المحاور الثلاثة (x, y, z).تم خلال المرحلة العملية تثبيت عدد من المجسات (strain gauges) على ساق المحراث وقياس الانفعالات، حيث اعتمد عامل التربة وبواقع نسيجين وعامل العمق وبواقع ثلاث مستويات (40، 45، 50) سم .اظهرت النتائج ان هناك اختلاف في قيم الاجهادات المتولدة من حيث مستويات العمق ولكلا النسيجين من التربة}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101071.html}, eprint = {https://rengj.mosuljournals.com/article_101071_043e549ed53f2ffe1da88b9e4935b7c3.pdf} } @article { author = {Ali, Bushra and Hayawi, Hana}, title = {Laboratory Study of Flow Characteristics Over Piano Key Weir}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {20-30}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101072}, abstract = {The main objective of this investigation is to obtain performance efficiency and the coefficient of discharge for Piano Key weir with downstream overhang. One hundred thirty five experimentswere conducted on models of Piano key weirs. Three slope of the inlet key (Si = 0.7, 0.6, 0.46), three different ratios for the inlet key width to the out let key width (Wi/Wo= 1, 1.61, 1.81) and three heights (p = 30, 25, 20) cm for each weir were used. The results showed that the slope of the inlet key (0.7) gavea lowervaluesof performance efficiency and a highest values of coefficient of discharge than (0.6, 0.46) keyswhile ratios of inlet key width to the out let key width (Wi/Wo = 1.81) gave a highest values of coefficient ofdischarge. An empirical relationship was found for estimate the coefficient of discharge and performance efficiency in relation to thenon dimensionless variable}, keywords = {Piano Key Weir,Discharge coefficient,Performance Efficiency}, title_ar = {دراسة مختبریه لخصائص الجریان فوق الهدار من نوع مفتاح البیانو}, abstract_ar = {یهدف البحث إلى دراسة الخصائص الهیدرولیکیة للهدار من نوع مفتاح البیانو. حیث تم إجراء 135 تجربة على نماذج الهدارات من نوع مفتاح البیانو بتدلی من جهة المؤخرة وذلک بأخذ ثلاثة میول لمفاتیح المقدم (Si = 0.7, 0.6, 0.46)وثلاثة نسب مختلفة لعرض مفتاح المقدم إلى عرض مفتاح المؤخر (Wi/Wo=1, 1.61, 1.81) وثلاث ارتفاعات للنموذج(P = 30, 25, 20) سم. أظهرت النتائج أن المیل (0.7) أعطى اقل قیمة لکفاءة الأداء وأعلى قیمة لمعامل التصریف یلیه المیل (0.6) و (0.46) کما أعطت نسبة عرض مفتاح المقدم إلى عرض مفتاح المؤخر (1.81)أعلى قیمة لکفاءة الأداء ومعامل التصریف. وتم إیجاد علاقة وضعیة لحساب معامل التصریف وکفاءة الأداء بدلالة المتغیرات اللابعدیة المؤثرة فیه.}, keywords_ar = {الهدار من نوع مفتاح البیانو,معامل التصریف,کفاءة الأداء}, url = {https://rengj.mosuljournals.com/article_101072.html}, eprint = {https://rengj.mosuljournals.com/article_101072_cb867c345a046f841bc5a6c09e725ae3.pdf} } @article { author = {Abid, Muzahim and Alani, Eftikhar and Ghazal, Entesar}, title = {Evaluating performance of Hydrus-1D model in simulating evaporation from soil surface for different wetting intervals}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {31-43}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101073}, abstract = {In this study, Hydrus-1D model was used to simulate the evaporation from the soil surface for different wetting intervals for northern region(sandy loam and clay loam) using input for climatic data , and data of class Apan evaporation.The results showed that data of pan evaporation class A can be relied on in simulating and calculation of evaporation from the soil surface, where the standards of statistics (IOA, R2) calculated on the basis of evaporation pan class A data are better for the wetting intervals (2,4, 8, 16 ) days compared with the values of those standards based on full climate data and both types of soil. The study also showed that the wetting intervals and their impact on evaporation from the soil surface and evaporation stages reasonably agree with the results of field experiments that have been made in this area.}, keywords = {Hydrus,D model,soil surface evaporation wetting intervals}, title_ar = {تقییم أداء Hydrus-1D فی محاکاة التبخر من سطح التربة لفواصل ترطیب مختلفة}, abstract_ar = {تم فی هذه الدراسة استخدام أنموذج Hydrus-1D لغرض إجراء محاکاة التبخر من سطح التربة لفواصل إرواء مختلفة ولنوعین من الترب للمنطقة الشمالیة (رملیة مزیجیة، طینیة مزیجیه) وبمدخلات من البیانات المناخیة، وبیانات التبخر من الاناء القیاسی. اظهرت نتائج الدراسة انه یمکن الاعتماد على بیانات الاناء القیاسی للتبخر لإجراء المحاکاة وحساب التبخر من سطح التربة حیث کانت المعاییر الاحصائیة الادائیة (IOA, R2 ) المحسوبة على اساس بیانات التبخر الانائی الافضل ولجمیع فواصل الترطیب المعتمدة (2،4،8،16) یوم بالمقارنة مع قیم تلک المعاییر المعتمدة على البیانات المناخیة الکاملة ولکلا نوعی التربة. کما اظهرت الدراسة ان فواصل الترطیب وتأثیرها على التبخر من سطح التربة ومراحل التبخر توافقت معنتائج التجارب الحقلیة التی تم اجراؤها فی هذا المجال.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101073.html}, eprint = {https://rengj.mosuljournals.com/article_101073_1045515df414bc25663e7ecf9303ae87.pdf} } @article { author = {Mohammed, Israa and Dawood, Shifaa}, title = {Pipelined Parallel Implementation of CryptosystemsBased on Advanced Encryption Standard}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {44-55}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101074}, abstract = {A hardware architecture implementation of Advanced Encryption Standard (AES) is globally adopted to encrypt data for variant communications systems, taking into account that AES is reliable, secured and immunized against attacks. A single crypto system is suggested to encrypt and/or decrypt different types of data .These types of data are assumed to be as a text data .The image is considered as a case study for the type of data that is to be encrypted in real time. Then the proposed architectures are used to encrypt the video within the time ≤ 33 m sec . Two architectures are proposed . The first one is a hybrid of both stream and block ciphering. This architecture is used to increase the encryption security by reducing the correlation among image pixels. The resulting encryption time for an image of (32x64)pixels is equal to 16.76 µ sec. The second architecture is proposed for CTR mode of AES algorithm. The same time achieved in the first architecture is also achieved in this implementation. However ,the half of the hardware resources in comparison with the first architecture is achieved in implementing the second, but if it is used for either encryption or decryption , not for both simultaneity. The real time implementation is achieved due to using parallel computation that is based on pipelining technique. The architecture are synthesized on Spartan-6 LX(XC6SLX16) using ISE 14.2 .}, keywords = {AES,FPGA,Image encryption,Pipeline design}, title_ar = {تنفیذ توازی خط الأنابیب لنظام تشفیر مبنی باستخدام خوارزمیة معیار التشفیر المتقدم}, abstract_ar = {}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101074.html}, eprint = {https://rengj.mosuljournals.com/article_101074_a91a327d4a2052aa474dee314faba8aa.pdf} } @article { author = {Yasoob, Ahmed and Kharrufa, Suhair and Abbawi, Suaad}, title = {Effect of Some Operating Parameters on the Performance of Ballasted Flocculation Technique for Water Treatment}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {56-72}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101075}, abstract = {The study aimed to apply the concept of Ballasted Flocculation (BF) at modified jar test for different turbidities for Tigris rivers raw water in order to find out the optimum values for each of :the additives chemicals, the ballasted agent doses and the operating conditions which are each of the detention time and velocity gradient A study of366 samples for six levels of initial synthetic turbidity of the Tigris River showed that it is possible to ad optBF technique successfully, and it reduces the time of the treatment phase and increase the stability of the quality of water treatment, but doesnotreducetheconcentrationsofthe chemicals which are used. The study showsthattheuseofalumconcentrationof30-40mg/Lwithpolymerconcentrationof0.2-0.4mg/L and BAconcentrationof0.5-2.5g/L forthe range of diametersbetween75-212 μmachievea residualturbidity ~1 NTU for supernatant water}, keywords = {}, title_ar = {تأثير بعض العوامل التشغيلية على أداء تقنية التلبيد المثقّل لمعالجة المياه}, abstract_ar = {تهدف الدراسة الى تطبيق تقنيةالتلبيد المثقّلBallasted Flocculation (BF) على جهاز الجرة المعدل من اجل تقييم كفاءة التقنية لعدة مستويات من العكورة لمياه نهر دجلة، ولإيجاد القيم المثلى لكل من: المضافات الكيميائية وجرعة المثقّلات الوزنية (Ballasted Agent (BA والظروف التشغيلية وهي كل من: ازمنة المكوث والانحدار السرعي.أظهرت نتائجدراسة 366 عينة لستة مستويات من العكورة الاولية المصنعة انه بالإمكان تبني تقنية التلبيد المثقّل بنجاح، وأنهاتقلل ازمنة المعاملة بمرحلة التلبيد والترسيب وتزيد ثبات نوعية المياه المعاملة، ولكن التقنية لا تقلل من التراكيز الكيميائية المستخدمة. وتبين بأن استخدام الشب بتركيز 30-40 ملغم/لتر وبوليمر موجب بتركيز 0.2-0.4 ملغم/لتر وBA بتركيز 0.5-2.5 غم/لتر لمدى اقطار ما بين 75-212 µmيحققعكورة متبقية تقارب 1 NTUللمياه المروقة.}, keywords_ar = {التلبيد المثق,منظومة اكتفلوا,المثق,البوليمرات}, url = {https://rengj.mosuljournals.com/article_101075.html}, eprint = {https://rengj.mosuljournals.com/article_101075_b57697dcc2b904ba2e3ef8dfd59272c5.pdf} } @article { author = {A. Abbo Al-Yase, Tara and Ali H. Al-Jameel, Dr.}, title = {Considering the Spatial Adjacency and Syntactic Properties Affecting the Functional Performance of the Socially Sustainable Schools in Iraq}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {73-90}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101076}, abstract = {The socially sustainable school is an emergent conceptappearedwithin the context of many significant changes in the world schools’ designs.Also, the functional performance is considered as a principal constituent for the socially sustainable schools. On the other hand, Iraqi schools are suffering, generally, from being of low functional performance; a problem resulted, as this research believes, from certain forms of considering the spatial adjacency and syntactic properties which are the mostinfluencing factors for the schools’ functional performance. This research tackles the problem that there are no clear conceptions about the extent and how those properties are consideredin the design practices of the Iraqi elementary schools. It adopts the objective of defining these conceptions using a method which includes defining the related influencing spatial adjacency and syntactic properties firstly, then measuringto what extent and how the defined properties are considered in the designs of Iraqi schools in comparision withthe world design practice framed by the general theory of the socially sustainable schools. After discussing the results, the final conclusions which define theweaknesses and defecitsof the local schools’ design practices regarding the consideration of the properties of interest are presented}, keywords = {Socially Sustainable Schools,Functional performance,Spatial Adjacency and Syntactic Properties}, title_ar = {إعتبار خصائص التجاور والتركيب الفضائي المؤثرة في الأداء الوظيفي للمدارس المستدامة اجتماعياً في العراق}, abstract_ar = {برز مفهوم المدرسة المستدامة اجتماعياً مؤخراً في سياق تغيرات هامة شهدتها نظريات وممارسات تصاميم المدارس في العالم، ويعدُّ الأداء الوظيفيمقوماً أساسياً بالنسبة لأبنية المدارس المستدامة اجتماعياً. بالمقابل تعاني المدارس العراقية عموماً، من تدني أدائها الوظيفي وهي مشكلة يرى البحث الحالي أنها ناتجة عن صيغ محددة في اعتبار خصائص التجاور والتركيب الفضائي بعدِّها الخصائص الأكثر تأثيراً في الأداء الوظيفي لأبنية المدارس، لذلك فإنهيتصدى لمشكلة عدم وضوحالتصورات الخاصةبدرجة وكيفية اعتبار تلك الخصائص في المدارس الإبتدائية العراقية على مستوى الممارسات التصميمية، واتخذ هدف تحديد تلك التصورات باعتماد منهج يتضمن تحديد خصائص التجاور والتركيب الفضائي المؤثرة أولاً، وقياس مدى وكيفية اعتبار تلك الخصائص بالنسبة للمدارس العراقية مقارنةً بالممارسات التصميميةالعالمية المؤطرة بالنظرية العامة للمدارس المستدامة اجتماعياً ثانياً، ثم مناقشة النتائج وصولاً إلى الإستنتاجات النهائية التي حددت طبيعة القصور والإنحراف في الممارسات المحلية فيما يخص إعتبار الخصائص المعنية.}, keywords_ar = {المدارس المستدامة اجتماعيا,الأداء الوظيفي,خصائص التجاور والتركيب الفضائي}, url = {https://rengj.mosuljournals.com/article_101076.html}, eprint = {https://rengj.mosuljournals.com/article_101076_65ead8fc9411cd9010ba4ddf202cd234.pdf} } @article { author = {Yahya, Dr.F. and Mohammad, Dr.Z. and Ali, Dr.S.}, title = {Estimation of Model Parameters, for Torsional Vibration Analysis ofa Turbo-Generator Unit with Reference to Mosul Gas-Turbine Station}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {91-116}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101077}, abstract = {In the design stage or analysis of any dynamical system a detailed or comprehensive model is essentially required. In this work, different parts and components that are contained in the model of a turbo-generator unit (T.G) for torsional vibration analysis are considered and the governing equations of which are presented and developed to estimate their respective parameters. These parts and components are mainly compressor seventeen stages and blades, turbine two stages and blades, reduction gear system with the safety shaft, the rotor of the generator, the exciter and the fluid film bearings on which the whole system is supported. The data upon which the system model is built are referred to Mosul gas turbine station units.The estimated parameters are those related to rotational inertia, damping and stiffness effects of the different components in the system.A detailed model of the system should be useful for the purpose of torsional vibrational during rotation with normal steady loading or under severe loading conditions utilizing a block diagram via Matlab. The system eigen values natural frequencies (critical speeds) and mode shapes are determined.}, keywords = {Torsional vibrations,stiffness,Damping,turbo,generator unit,Natural frequency}, title_ar = {تخمین معلمات النموذج لغرض تحلیل الاهتزازات الالتوائیة فی وحدة تولید توربینیة بالرجوع الى محطة تولید کهرباء الموصل الغازیة}, abstract_ar = {هنالک بالضرورة حاجة الى نمذجة تفصیلیة او شاملة فی مرحلة التصمیم او التحلیل لای منظومة داینمیکیة. فی هذا البحث اخذت بالاعتبار مختلف الاجزاء والمکونات التی یشتمل علیها النموذج لوحدة توربینیة لغرض تحلیل الاهتزازات الالتوائیة. تم تقدیم او تطویر المعادلات الحاکمة لغرض تخمین المعلمات المتعلقة بالنموذج. هذه الاجزاء والمکونات وبشکل اساسی,هی الضاغطة بمراحلها السبعة عشر والریش والتوربین بمرحلتیه مع الریش ومنظومة التروس لتخفیض السرعة مع عمود الامان ودوار المولد والمحفز وکذلک المحامل المزیتة التی یستند علیها النظام. المعلمات المراد تخمینها هی تلک المتعلقة بتاثیر القصور الذاتی والتخمید والنابضیة فی مختلف اجزاء المنظومة. الانموذج التفصیلی الذی تم تطویره یمکن الاستفادة منه لغرض تحلیل الاهتزازات الالتوائیة اثناء الدوران وفی حالة الاحمال الاعتیادیة الثابتة وعند ظروف الاشتغال القاسیة وباستخدام التمثیل الصندوقی مع برنامج الماتلاب تم حساب جذورمعادلات المنظومة وقیم الذبذبات الطبیعیة (السرع الحرجة) واشکال الاطوار.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101077.html}, eprint = {https://rengj.mosuljournals.com/article_101077_0b832e79b899676181aeeed2453b2d28.pdf} } @article { author = {I. Al-Abushi, Ramiz}, title = {Numerical study of natural convection heat transfer from a heater placed in an enclosure with adjacent inclined sidewall}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {117-132}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101078}, abstract = {In this investigation , natural convection heat transfer from a heater placed on the bottom of a square enclosure with adjacent inclined wall was carried out . The inclined wall has a constant lowtemperature , while the heater element has a constant high temperature ,and the remaining walls are insulated . The working fluid used is air with Prandtl number (Pr=0.72) . The governing equations of the problem are solved numerically by using finite differencemethod . The numerical solution is presented for various Rayligh numbers,Ra(103-105) , with different dimensionless parameters as length of heater (Yh¬) (0.1,0.3,0.5), different locations of the heater (Xh) (0.25,0.5) and inclination angle of inclined cold wall  (10o, 20o, 30o). The results are presented by isotherms and streamlines to show the behavior of the flow and temperature distribution .While the numerical results of heat transfer are presented by average Nusselt number and local Nusselt numbers at right , left and top sides of heater.The results show the effect of dimensionless parameters on heat transfer and Nusselt number.It is observed that the Nusselt number increased by increasing Raylig number , heater length , inclination angle of cold wall and where the heater is near the cold wall (Xh=0.5).}, keywords = {natural convection,heater,enclosure,heat transfer}, title_ar = {دراسة عددية لانتقال الحرارة بالحمل الطبيعي من مسخن موضوع في حيز ذو جدار مائل}, abstract_ar = {}, keywords_ar = {الطبيعي,مسخن,حيز,انتقال الحرارة}, url = {https://rengj.mosuljournals.com/article_101078.html}, eprint = {https://rengj.mosuljournals.com/article_101078_623cd053017971434982a539f34fa08a.pdf} } @article { author = {Aldabbagh, Mohammad}, title = {Optimum design of a heat pipe}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {133-146}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101079}, abstract = {This research deals with the optimum design of the heat pipe components using Matlab program, version 7, at the determined operating conditions. The heat pipe is used to transfer maximum available thermal energy to heat the feed water entering steam boiler . The affecting parameters on heat pipe performance were detailed as well as the transport limitations and the thermal resistances of the heat pipe parts. Satisfactory results were obtained for the heat pipe dimensions, components and design influentials. Also, the parameters affecting the heat transfer rate and the working fluid mass-flow rate were discussed. From the important results, the heat pipe heat transfer capability is directly proportional with each of the heat pipe bore, the wick c/s area and the heat pipe effective length, and inversely with each of the capillary radius and the working fluid viscosity.}, keywords = {Heat Pipe,Optimum design,Steam boiler}, title_ar = {التصمیم الأمثل لأنبوب حراری}, abstract_ar = {یتناول هذا البحث التصمیم الامثل لاجزاء ومکونات انبوب حراری باستخدام برنامج Matlab الاصدار 7، عند ظروف التشغیل المحددة. یستخدم الانبوب الحراری لنقل اکبر طاقة حراریة ممکنة لتسخین الماء المغذی الداخل الى مرجل بخاری .وقد تم تفصیل العوامل المؤثرة على اداء الانبوب الحراری ومحددات انتقال الحرارة والمقاومة الحراریة لاجزاء الانبوب الحراری، والحصول على نتائج مرضیة لابعاد ومکونات الانبوب الحراری ومؤثرات التصمیم، وکذلک مناقشة العوامل المؤثرة على کل من معدل إنتقال الحرارة ومعدل جریان کتلة مائع التشغیل.من النتائج المهمة هی ان مقدرة الانبوب الحراری على نقل الحرارة تتناسب طردیا وکل من قطر الانبوب ومساحة مقطع الفتیلة والطول المؤثر للانبوب، وعکسیا مع کل من نصف القطر الشعری ولزوجة مائع التشغیل.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101079.html}, eprint = {https://rengj.mosuljournals.com/article_101079_72521e9c25a6016ea24fc7191aa4e5a1.pdf} } @article { author = {Abed Fathi, Mohammed}, title = {Study of the Ultrasonic Behavior in (α + β`) Brass Alloy}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {147-152}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101080}, abstract = {Copper is one of the few metals with significant commercial uses. Although frequently used as a pure metal or with small amounts of metal additives, copper can form 82 binary alloys. Two of the most common are brass (copper-zinc) and bronze (copper-tin). This research work tries to study the ultrasonic behaviour in one of the important brass alloys represented by (α + β`) brass alloy. Specimens of (α + β`) brass were machined to cylindrical shape with different thicknesses in order to study the effect of the sound scanning distance on the acoustic attenuation of the ultrasonic waves. The results indicate that it is plausible to inspect (α + β`) brass using both 2MHz and 4MHz frequencies, and that the acoustic attenuation of ultrasonic waves has increased when 4MHz probe was used. In addition, the results illustrate that the acoustic attenuation increases as the sound path distance increases.}, keywords = {}, title_ar = {(α + β`) دراسة سلوک الموجات فوق الصوتیة فی سبیکة براص}, abstract_ar = {یستخدم النحاس على نطاق تجاری واسع، وبالرغم من إستخدامه بکثرة کمعدن نقی او مع بعض الاضافات المعدنیة الا أن النحاس یشکل 82 سبیکة ثنائیة. أثنان من أکثر السبائک شیوعاَ هما البراص ( نحاس- زنک) والبرونز (نحاس- قصدیر). یحاول هذا العمل الیحثی دراسة سلوک الموجات فوق الصوتیة من خلال بعض العوامل التقنیة فی سبیکة براص (α + β`). تم تشغیل نماذج من سبیکة البراص(α + β`) الى أشکال اسطوانیة مختلفة السمک بما یتلائم مع مجسات الموجات فوق الصوتیة. واستخدمت مجسات الموجات التضاغطیة (Compression waves probes) بترددات (2MHz and 4MHz) لفحص النماذج. أظهرت النتائج التی تم الحصول علیها فی هذا البحث أمکانیة نفاذ الموجات فوق الصوتیة داخل النماذج لاغراض الفحص الهندسی باستخدام کلا الترددین ) 2MHz and 4MHz (، وکذلک إزدیاد الاضمحلال الصوتی داخل النماذج باستخدام المجس ذو التردد 4MHz. کما بینت النتائج زیادة الاضمحلال الصوتی بزیادة المسافة المقطوعة باستخدام کلا الترددین ) (2MHz,4MHz}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101080.html}, eprint = {https://rengj.mosuljournals.com/article_101080_584821178446d5b22b74c4665f7a5a75.pdf} } @article { author = {N. Yahya, H. and N. M. Al-Faydi, S. and J. M. Abdul-Jabbar, Dr.}, title = {Neuro-Fuzzy Based ECG Signal Classification with A Gaussian Derivative Filter}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {153-166}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101081}, abstract = {In this paper, a neuro-fuzzy classification method is used for identifications of ECG signals. A feature extraction method with a QRS like filter (first order Gaussian derivative filter) is used. Five standard parameters (energy, mean value, standard deviation, maximum and minimum) are extracted from these diseasefeatures and then used as inputs for the neuro-fuzzy classification system. The ECG signals are importedfrom the standard MIT-BIH database. Five types of ECG signalsare used for classification; they are normal sinus rhythm (NSR), left bundle branch block (LBBB), right bundle branch block (RBBB), premature ventricular contraction (PVC) and pacemaker (PM). The proposed system combines the neural network adaptive capabilities and fuzzy inference system with the suitable filter design to give a promising classification accuracy of 99%.}, keywords = {Neuro,fuzzy system,ECG signal,Gaussian Derivative Filter,QRS,like filter,NSR,LBBB,RBBB,PVC and PM}, title_ar = { تصنيف اشارة القلب باعتماد النظام العصبي المضبب ومرشح نوع مشتقة كاوس}, abstract_ar = {الخلاصةفي هذا البحث, تم استخدام طريقة التصنيف باعتماد (Neuro – fuzzy) لاغراض التعرف على اشارات ECG . واستعملت طريقة لاستخلاص السمات بالاعتماد على مرشح ذو استجابة بنوع مشتقة كاوس الاولى والتي تشبه تركيبة QRS في اشارة اﻟECG . تم بعد ذلك استخدام تلك السمات كادخالات لمنظومة التصنيف باعتماد (Neuro - fuzzy) .اٍن اشارات ECG المستخدمة في هذا البحث تم الحصول عليها من (The standard MIT-database) . واستخدم منها خمس انواع هي (NSR) ̦ (LBBB) ̦ (RBBB) ̦ (PVC) ̦ (PM) . ان المنظومة المستخدمة تجمع بين الامكانات المتكيفة للشبكات العصبية وبين الموائمة الضبابية مع التصميم المناسب للمرشح وهذا اعطى دقة تصنيف واعدة وبنسبة 99% .}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101081.html}, eprint = {https://rengj.mosuljournals.com/article_101081_a1db06bd242316887786fdab11421f85.pdf} } @article { author = {A. Dawwd, Shefa and Al-Saegh, Ali}, title = {RAM-Based Neural Network Parallel Implementation on a Reconfigurable Platform and Its Application for Handwritten Digits Recognition}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {167-178}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101082}, abstract = {Artificial neural networks (ANNs) are widely used in different areas of nowadays applications. Many challenges are imposed on the practical implementation of ANNs. Some of them are: the number of samples required to train the network; the number of adders, multipliers, nonlinear transfer functions, storage elements; and the speed of calculations in either training phase or recall phase. In this paper, the RAM-based neural network is investigated. No weights, adders, multipliers, transfer functions are required to implement it neither in hardware nor in software, but at a cost of large RAM utilization. In addition, a small number of samples are required for training. However, in hardware implementation, a large size of memory is required to train it.The network is implemented on the FPGA platform. The Stratix IV GX FPGA development board, which is provided on large on board RAM, is used. A considerable speedup of 237is achievedin either training or recalling phases. A comparable error rate of 7.6 is achieved when MNIST (Mixed National Institute of Standards and Technology) database are used to train the network on handwritten digit recognition.}, keywords = {Field programmable gate arrays,handwritten digits recognition,Ram,based neural network}, title_ar = {تصميم شبكة عصبية مبنية على ذاكرة الوصول العشوائي وتنفيذها على الوحدات القابلة لإعادة التشكيل وتطبيقها في تمييز الأرقام المكتوبة باليد}, abstract_ar = {تستخدم الشبكات العصبية الإصطناعية في العديد من التطبيقات الموجودة في الحياة اليومية. ولكن هناك الكثير من التحديات التي تواجه تطبيق هكذا شبكات في الواقع العملي. ويمكن تلخيص تلك التحديات بالتالي: عدد النماذج المطلوبة لتدريب الشبكة، عدد عمليات الجمع والضرب وعدد الدوال غير الخطية وكذلك عدد وحدات الخزن المطلوب التعامل معها وتوفيرها، وسرعة الحسابات في طوري التدريب والفحص. تم في هذا البحث إستخدام الشبكة العصبية المبنية على ذاكرة الوصول العشوائي، حيث أن تطبيقها عمليا لا يتطلب أوزان أوعمليات جمع وضرب أو دوال تحويل ولكنه يتطلب توفير ذاكرة الوصول العشوائي. تتميز هذه الشبكة بالعدد القليل من نماذج التدريب المطلوبة ولكنها تكون على حساب حجم ذاكرة الوصول العشوائي. تم في هذا البحث تصميم شبكة عصبية من هذا النوع وتنفيذها بإستخدام مصفوفة البوابات المنطقية القابلة للبرمجة في الحقل. تم فحص النظام المقترح في تمييز الأرقام المكتوبة باليد وكانت نسبة الخطأ في التمييز هي 7,6% مع تحقيق تسريع جدير بالإعتبار ومقداره 237.}, keywords_ar = {مصفوفة البوابات المنطقية القابلة للبرمجة في الحقل,تمييز الأرقام المكتوبة باليد,شبكة عصبية مبنية على ذاكرة الوصول العشوائي}, url = {https://rengj.mosuljournals.com/article_101082.html}, eprint = {https://rengj.mosuljournals.com/article_101082_6075b874c161399b425480845f194ac4.pdf} } @article { author = {K. ZEYNAL, Emdad and Moayad M.Kasim, Dr.}, title = {Mechanical Properties of Wood Shavings-Cement Lightweight Composites}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {179-186}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101083}, abstract = {Abstract The use of wood shavings, as a recycled waste product from the wood furniture industries is an interesting technique to produce lightweight cement composites. This study aims at examining the mechanical properties of wood shavings-cement lightweight composites. First, the wood shavings were pre-treated with water or superplasticizer or Cement Based Bitumen Emulsion (CBBE). Then, the compressive strength and tensile strength of the wood-cement matrix were experimentally evaluated. Finally, it is shown that the addition of wood shavings to cement paste gives a composite with satisfactory mechanical strengths with respect to its weight and higher toughness in addition to environmental and economic benefits.}, keywords = {compressive strength,lightweight composite,Tensile Strength,toughness,wood shavings}, title_ar = {الخواص الميكانيكية لمركبات رقائق الخشب والسمنت خفيفة الوزن}, abstract_ar = {الخلاصةاستخدام رقائق الخراطة الخشبية الناتجة من مخلفات صناعات الاثاث الخشبية تعتبر اسلوبا تقنيا ممتعا لأنتاج مركبات خفيفة الوزن. هذه الدراسة تهدف اختبار الخواص الميكانيكية للمركبات الخفيفة الوزن الناتجة من رقائق الخشب-السمنت. بداية تم معالجة رقائق الخشب بالماء أو بالملدنات الفائقة أو بالمستحلب القيري ذو الاساس السمنتي. ثم تم تجريبيا تحديد مقاومة الانضغاط, مقاومة الشد للمزيج الخشبي-السمنتي. أخيرا, فقد أظهرت النتائج أن إضافة الرقائق الخشبية الى عجينة السمنت تنتج مركبا ذو مقاومة ميكانيكية مرضية نسبيا مع وزنه وصلابة عالية بالاضافة إلى مزايا اقتصادية وبيئية.}, keywords_ar = {مقاومة الانضغاط,مركب خفيف الوزن,مقاومة الشد,الصلابة,رقائق خشبية}, url = {https://rengj.mosuljournals.com/article_101083.html}, eprint = {https://rengj.mosuljournals.com/article_101083_7347cb3b8aac991003237f3836be116b.pdf} } @article { author = {Thanon Dawood, Dr.Eethar}, title = {Experimental study of lightweight concrete used for the production of canoe}, journal = {Al-Rafidain Engineering Journal (AREJ)}, volume = {23}, number = {2}, pages = {187-197}, year = {2015}, publisher = {College of Engineering, University of Mosul, IRAQ}, issn = {1813-0526}, eissn = {2220-1270}, doi = {10.33899/rengj.2015.101085}, abstract = {Abstract This study was conducted to investigate the properties of lightweight concrete produced by the inclusions of polystyrene beads and perlite that can be used for production of Canoe.Different percentages of polystyrene (20, 35, 50 and 65%) were used.Besides, the 50% of polystyrene beds with different percentages of perlite (10, 20, 30, 40, 50 and 60%) as partial replacement of sandwere used. The fresh density, compressive strength, flexural strength and absorption capacity of the mixes were tested. The results show that the uses of 50% of polystyrene with 50% of perlite as partial replacementof sand exhibit suitable ranges of density, compressive and flexural strengths of lightweight concrete used for canoe production. Thus, the Canoe produced from these inclusions of polystyrene and perlite show a clear success in terms of floating.}, keywords = {Concrete Canoe,Lightweight concrete,Perlite,polystyrene}, title_ar = {دراسة تجريبية للخرسانة الخفيفة الوزن المستخدمة في صناعة القوارب الخرسانية}, abstract_ar = {هذا البحث يتناول دراسة خصائص الخرسانة الخفيفة الوزن المصنعة من قطع الفلين مع البرلايت وذلك لتصنيع قارب خرساني. لذلك تم استخدام نسب مختلفة من الفلين وهي 20 و 35 و50 و 65%. بالاضافة الى ذلك فان نسبة 50% من الفلين تم استخدامها مع نسب مختلفة من البرلايت كاستبدال جزئي من الرمل وهذه النسب هي 10و 20و 30و 40 و50و 60%. الكثافة الرطبة ومقاومة الانضغاط ومقاومة الشد والامتصاص تم اختبارها للخلطات الخرسانية الخفيفة المصنعة. النتائج بينت بان استخدام نسبة 50% من الفلين مع 50% من البرلايت كاستبدال جزئي من الرمل اعطت مديات من الكثافة والمقاومة مناسبة لتصنيع القارب الخرساني. ولهذا فان القارب الخرساني المصنع من هذه الخلطة المحتوية على الفلين والبرلايت اظهرت نجاح واضح في فحص الطفو للقارب.}, keywords_ar = {}, url = {https://rengj.mosuljournals.com/article_101085.html}, eprint = {https://rengj.mosuljournals.com/article_101085_172fd555fa9d6a31fb38b9d83595aace.pdf} }