eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
1
10
10.33899/rengj.2010.32798
32798
Corrosion Protection of Steel Pipe Samples Buried in Soil
حماية من التآكل لنماذج من أنبوب فولاذي مدفونة في التربة
Haitham M. Wadullah
1
The types of corrosion protection on corrosion resistance of steel pipe samples buried in soil have been studied in this research. Samples of unprotected carbon steel are used with other protected by different corrosion protection such as galvanic coating, rubber coating and two types of cathodic protection (impressed current and sacrificial anodes). The weight loss technique is used as a function of the corrosion rate (mdd).
The results, which have been obtained, show that the corrosion rates in the unprotected samples are high compared with the corrosion protected samples, and the maximum corrosion resistance is found to be at the cathodic protection systems.
Key words: Corrosion protection, Samples of steel pipe, Buried in soil
المستخلص جرى في هذا البحث دراسة تأثير نوع الحماية من التآكل على مقاومة تآكل نماذج من أنبوب فولاذي مدفونة في التربة. تضمن العمل إعداد وتحضير نماذج من الصلب الكاربوني غير المحمية وأخرى محمية من التآكل بطرق حماية مختلفة وهي الحماية بالغلفنة والحماية الكاثودية بمصدر جهد خارجي وحماية كاثودية بمزدوج غلفاني وحماية بالتغطية بالمطاط ، وضعت النماذج المحمية والنماذج غير المحمية في وسط التآكل والمتمثل بالتربة . تم استخدام علاقة رياضية مقاسه بوحدة (mdd) كدالة لقياس معدل التآكل. وتبين من النتائج إن معدل تآكل النماذج غير المحمية هو الأعلى بينما أظهرت الحماية الكاثودية أعلى مقاومة للتآكل. الكلمات الدالة: حماية من التآكل، نماذج من أنبوب فولاذي، مدفونة في التربة
https://rengj.mosuljournals.com/article_32798_faf2a884a9c36e28ff758abdedbe49bb.pdf
Key Words
Samples of steel pipe
Buried in soil
الكلمات الدالة
نماذج من أنبوب فولاذي
مدفونة في التربة
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
1
13
10.33899/rengj.2010.32841
32841
FINITE ELEMENT ANALYSIS OF SHEAR TRANSFER OF FIBROUS CONCRETE UNDER COMPRESSIVE STRESS
التحلیل بطریقة العناصر المحددة لانتقال القص للخرسانة اللیفیة تحت تأثیر اجهادات انضغاط
B. J.Al-Sulaifanie
1
J. R.Al-Feel
2
ABSTRACT: This study presents a numerical analysis of push-off and modified push-off fibrous concrete specimens. The investigated variables were, volume fraction of fibres, area of reinforcement, and the ratio of the compressive to the shear stress. Eight nodes isoparametric elements were used to represent concrete, and embedded bar elements to represent the reinforcement. The nonlinear behaviour of fibrous concrete in compression, tension and the reduction of the shear modulus due to cracking were taken into account. The numerical results showed good agreement with the experimental results, the average ratio of the calculated to the experimental first crack shear stress is (0.955), and the average ratio of the calculated to the experimental shear strength was (0.981). The cracks patterns showed that the fibrous specimens have less numbers of cracks than that of plain specimens at a certain shear force, and the presence of fibres delay the initiation the cracks. The calculated slip is slightly more than the experimental slip at early stage of loading and the difference increased prior to the failure load. Key Words: cement, contour, cracks pattern, fibres, finite element, shear transfer.
ألخلاصةتقدم هذه الدراسة تحلیلا عددیا لنماذج الدفع ونماذج الدفع المحورة للخرسانة اللیفیة. المتغیرات التی تم دراستها هی النسبة الحجمیة للالیاف، مساحة التسلیح، نسبة اجهاد الانضغاط الى اجهاد القص. تم استخدام عناصر ذات ثمانیة عقد لتمثیل الخرسانة وعناصر قضبان مطمورة لحدید التسلیح. تم اخذ السلوک غیر الخطی للخرسانة اللیفیة فی النضغاط والشد وکذلک نقصان معامل القص بسبب التشقق نتائج التحلیل العددی اظهرت توافقا جید مع النتائج العملیة، معدل نسبة النتائج العددیة الى العملیة لاجهادات القص فی مرحلة التشقق تساوی(0.955) وللمقاومة العظمى تساوی (0.981). الشقوق فی نماذج الخرسانة اللیفیة تکون أقل عددا من الشقوق فی الخرسانة الاعتیادیة فی قوة قص معینة ووجود الالیاف یؤخر ظهور الشقوق. الانزلاق المحسوب کانت اعلى قلیلا من النتائج العملیةفی المراحل المبکرة من تسلیط الاحمال وزاد الفرق بزیادة الاحمال قبل الفشل
https://rengj.mosuljournals.com/article_32841_f466bed57222daa8785a811d7d6dbfff.pdf
Key Words
contour
cracks pattern
fibres
finite element
shear transfer
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
14
23
10.33899/rengj.2010.32851
32851
ANONLINEAR ANALYSIS OF FIBROUS REINFORCED CONCRETE SLABS BY ASSUMED STRAIN AND HETEROSIS ELEMENTS
ألتحليل غير الخطي للبلاطات الخرسانية الليفية المسلحة بطريقة العناصر المحددة ذات الانفعال المفروض
Dr. A. A. Abdul-Razzak
1
Nuha H. Al-Jubory
2
Abstract
In the present work, the finite element method has been used to investigate the behavior of fibre reinforced concrete slabs in the pre and post-cracking levels up to the ultimate load. Assumed transverse shear strain is used in the formulation to overcome the shear locking, and Heterosis elements are employed in the analysis.
Both an elastic-perfectly plastic and strain hardening plasticity approach have been employed to model the compressive behavior of the fibre concrete. The yield condition is formulated in terms of the first two stress invariants. Concrete crushing is a strain-controlled phenomenon, which is monitored by a fracture surface similar to the yield surface. A layered approach is adopted to discretize the concrete through the thickness. A tension stiffening model has been suggested by making a regression analysis of the experimental results, with index of determination (90.61%).
The steel is considered either as an elastic perfectly plastic material or as an elastic-plastic material with linear strain hardening. Steel reinforcement is assumed to have similar tensile and compressive stress-strain relationship.
Keywords: Finite Element Method, Slab, Steel Fibre Reinforced Concrete, Tension
الخلاصةفي هذا البحث تم إجراء التحليل غير الخطي بطريقة العناصر المحددة لبحث أداء البلاطات الخرسانية الليفية المسلحة في مرحلة ما قبل التشقق وبعدها إلى الحمل الأقصى. استخدم نوعين من العناصر ، العناصر ذات الانفعال المفروض للتخلص من ظاهرة القفل بالقص وعناصر هيتروسز . مثل سلوك الخرسانة في حالة الانضغاط كمادة مرنة تامة اللدونة أو كمادة مرنة مع انفعالات لدنة متصلدة . شروط الخضوع عبر عنها بدلالة أول متغيرين للإجهاد . حركة سطوح التحميل المتعاقبة حكمت بقاعدة التصلب التي تحدد من علاقة الإجهاد – الانفعال أحادي المحور والمعبر عنها بدلالة قطع مكافئ . تهشم الخرسانة هي ظاهرة محكومة بالانفعال ومنظمة بسطح سحق يشبه سطح الخضوع . كما استخدم أسلوب تقسيم السمك إلى طبقات لتمثيل الخرسانة خلال السمك. ولغرض تمثيل تأثير صلابة الشد في الخرسانة المتشققة تم اقتراح نموذج بالاعتماد على نتائج عملية وقد أعطى هذا النموذج معامل توافق ( 90.61% ). حديد التسليح اعتبر كمادة مرنة تامة اللدونة أو كمادة مرنة لدنة مع تصلب انفعال خطي.
https://rengj.mosuljournals.com/article_32851_511eafb05788829d4932ee7b1683f07a.pdf
KEYWORDS
Slab
Steel Fibre Reinforced Concrete
Tension Stiffening Model
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
24
34
10.33899/rengj.2010.32863
32863
Influence of Limestone Powder as Partial Replacement of Cement on Concrete and the Effect of High Temperature on It
تأثير مسحوقِ الجير كبديل جزئي مِنْ الإسمنتِ على الخرسانةِ ومفعولِ درجةِ الحرارة العاليةِ عليها
Zena Adel Mohammed
1
Rana Burhan Abdurrahman
2
Dr. Abdul Hakeem Hamed Ahmad
3
Abstract
In the recent years, the uses of the binding materials of different types in addition to cement become very wide in the product of concrete as blending of portland cement with limestone, so it is necessary to investigate the influence of the binder material on the concrete properties. In order to asses the performance of this type of concrete, it is important to understand the changes in the concrete properties especially in case of exposure to elevated temperature.
This paper summarize and discuss the effect of the limestone powder (CaCO3) as a compensating material with cement on the compressive and tensile strength and discuss the effect of elevated temperature on this type of concrete.
Limestone powder (LP) was used as a compensating material with different ratio of cement include (0, 10, 15, 20, 25) %. Compressive and tensile strength were investigated before and after the exposure to high temperature including (200, 400, 600) °C.
The study show that limestone compensate changes in both compressive, and tensile strengths. Negative effects on the properties observed as the amount of limestone exceeds 15% of the cement weight. After the exposure to high temperature the results show a drop in compressive and tensile strengths in a different form.
Key words: Limestone powder; elevated temperature
الخلاصة في السنوات الاخيرة، أصبح انتاج الخرسانة باستخدام مواد رابطة مع الاسمنت شائعا كالاسمنت المستبدل جزئيا مع مسحوق الجير ،فأصبح من الضروري معرفة تأثير هذه المواد ونوعها على خصائص الخرسانة ومن أجل تقييم أدائها فمن المهم معرفة التغييرات التي يمكن ان تحدث فيها خصوصا عند تعرضها للحرارة العالية. أشتمل البحث على تلخيص ومناقشة تأثير مسحوق الجير(CaCO3) كمادة تعويضية مع الاسمنت على مقاومة الانضغاط والشد وتأثير الحرارة العالية عليها، استخدم مسحوق الجير كمادة تعويضية مع الاسمنت بنسب مختلفة تضمنت (0،10،15،20،25)% تم دراسة مقاومة الشد والضغط بعد التعرض للحرارة العالية التي شملت°C (200،400،600). أظهرت النتائج تأثير مسحوق الجير على مقاومتي الانضغاط والشد وبدأ التأثير السلبي عندما زادت النسبة عن 15% كما ان التعرض للحرارة العالية أدى الى خفض مقاومتي الانضغاط والشد بنسب مختلفة للمزجات الخرسانية.
https://rengj.mosuljournals.com/article_32863_d4b38da7289e19f49e5cf1106221e757.pdf
Key Words
elevated temperature
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
35
49
10.33899/rengj.2010.32877
32877
Tensile Strength of Short Headed Anchors Embedded in Steel Fibrous Concrete
مقاومة الشد للمثبتات القصيرة ذات الرؤؤس المطمورة في خرسانة ليفية فولاذية
S. A. Al- Ta
1
A. A. Mohammed
2
ABSTRACT
This paper deals with the tensile behaviour and strength of cast-in-place short headed anchor bolts embedded in both normal concrete (NC) and steel fibre reinforced concrete (SFRC). Four volume fractions (vf =0.4%, 0.8%, 1.2%, and 1.6%), two aspect ratios (lf / df =19.63, 36.33), three bolt diameters (db =8, 10, 12mm), and four embedment depths (hef =25, 37.5, 50, 62.5mm) were used. More than (108) specimens were tested under monotonic tensile loading. Only (90) specimens were failed by large concrete failure cone exceeding the dimensions of the specimen and the cone breaks into pieces in most cases (concrete failure), while the other specimens were failed by yielding or fracture of the bolts (steel failure). Tests results showed that breakout capacity ( ) of the anchors were significantly enhanced by the addition of steel fibers to concrete and the size of the failure cone in (SFRC) specimens were smaller than the size of failure cones in (NC).
Key word: Breakout capacity, cast-in-place, failure cone, headed anchor bolt, pullout test, steel fibers.
الخلاصةيتضمن هذا البحث دراسة مقاومة وسلوك الشد للبراغي القصيرة ذات الرؤؤس المطمورة في خرسانة عادية وخرسانة مسلحة بالالياف الفولاذية. استعملت اربع نسب للالياف الفولاذية (0.4%، 0.8%، 1.2%، و%1.6)، نسبتين باعيتين للالياف (19.63 و 36.33)، ثلاثة اقطار للبراغي (8، 10، و mm 12)، واربعة اعماق دفن (25، 37.5، 50، و62.5mm ). تم تحضير أكثرمن 108 نموذج وفحصت تحت تأثير حمل شد متزايد. فشلت 90 من النماذج فقط على شكل مخروط خرساني زادت ابعاده عن ابعاد النماذج وانقسم المخروط الى عدة أجزاء في معظم الحالات، بينما فشلت النماذج الاخرى بانقطاع البرغي (فشل الحديد). أظهرت النتائج أن مقاومة الشد للبراغي تتحسن بشكل ملحوظ باضافة الالياف الفولاذية وان حجم المخروط الخرساني أقل في الخرسانة الليفية عما هوعليه في الخرسانة الاعتيادية.
https://rengj.mosuljournals.com/article_32877_4d72f9ce83560f7f946e3fcbb4cbf7c1.pdf
Key Word
Cast
place
failure cone
headed anchor bolt
pullout test
Steel Fibers
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
50
62
10.33899/rengj.2010.32884
32884
BEHAVIOR OF CONCRETE STRENGTHENED WITH CARBON FIBER REINFORCED POLYMER LAMINATE AT HIGH TEMPERATURE
سلوك الخرسانة المقواة بصفائح الكاربون المعرضة الى حرارة عالية
AZAD A. MOHAMMED
1
ABDULJALIL S. AHMED
2
ABSTRACT
In this paper the effect of high temperature on plain concrete strengthened with Carbon Fiber Reinforced Polymer ( CFRP ) sheets and behavior of concrete strengthened after heating were studied for flexure and compression properties . For this purpose a total of 44 prismatic specimens of 100x100x350 mm dimensions were tested . Results indicate that due to high temperature there is a continuous reduction in flexural strength of concrete strengthened with CFRP sheet . Deflection corresponding to flexural strength also reduced for exposure temperature higher than 350oC . The effect of finishing CFRP layers with cement mortar for controlling the reduction of flexural and compressive strengths due to high temperature was found to be not important . According to the obtained results , plain concrete damage by high temperature can be repaired using CFRP sheets for compressive strength of about 74% of that of plain concrete , and flexural strength of about 69% of that of strengthened concrete before heating .
KEYWARDS:Bond ,CFRP, Compression , Flexure ,Heating , High Temperature ,Strengthening, Wrapping
في البحث الحالي تم دراسة تأثير الحرارة العالية على خواص الانحناء والانضغاط للخرسانة المقواة بصفائح الكاربون ودراسة تأثير التقوية على الخرسانة المتضررة بسبب الحرارة العالية . لهذا الغرض تم تهيئة و فحص 44 نموذجا موشوريا بابعاد 100х 100 х 350 ملم . النتائج الحاصلة تؤكد بأن هناك نقصان مستمر في مقاومة الانحناء للخرسانة المقواة بصفائح الكاربون مع زيادة درجة الحرارة . الاود المصاحب لمقاومة الانحناء ايضا تأثر بسبب الحرارة لكن بنسبة قليلة لدرجات الحرارة اقل من 350 درجة مئوية . تأثير الانهاء بواسطة مونة السمنت للسيطرة على نقصان مقاومة الانحناء والانضغاط كان قليلا . حسب النتائج الحاصلة , الخرسانة المتضررة بالحرارة العالية يمكن صيانتها بواسطة الياف الكاربون للحصول على مقاومة انضغاط بنسبة %74 من المقاومة الاصلية و بنسبة %69 من مقاومة الانحناء مقارنة مع مقاومة الانحناء للخرسانة المقواة قبل التعرض .
https://rengj.mosuljournals.com/article_32884_fc4dda293113679ee7ef309f633a2494.pdf
KEYWARDS
CFRP
Compression
Flexure
Heating
High Temperature
Strengthening
Wrapping
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
63
72
10.33899/rengj.2010.32887
32887
Investigation of Macrocell / Microcell Channels Selection In Multitier Cellular Networks
تقصي اختيار القنوات لخلية كبيرة (ماكرو) متكونة من عدة خلايا صغيرة (مايكرو) في شبكة النظام الخلوي
SAMI A. MAWJOUD
1
FARHAD E. MAHMOOD
2
Abstract
A proposed method of Macrocell / Microcell channel selection in multitier cellular system using sojourn time of microcell overlapped region. To keep the handoff rate to acceptable level, low mobility users (with speed V < Vth) should undergo handoffs at microcell boundaries and high mobility users (with speed V > Vth) should undergo handoffs at macrocell boundaries. Investigation of variation of the number of channels in the microcells and the macrocell with the blocking probability. Also the variation of microcell radius on the blocking probability for different mobile stations speed.
Keywords: Macrocell, Microcell, Channel Selection.
المستخلص تم اقتراح طريقة لانتقاء قنوات الماكرو/مايكرو في النظام الخلوي باستخدام زمن البقاء في منطقة التراكب (Overlap) للخلية المايكرو.لإبقاء معدل المناقلة إلى مستوى مقبول ، فان المستخدمين ذوي السرعة القليلة ( بسرع V < Vth ) يجب أن تتم المناقلة عند حدود الخلية الصغيرة الـ (المايكرو) ، والمستخدمين ذوي السرع العالية ( بسرع V > Vth ) تتم المناقلة عند حدود الخلية الكبيرة (الماكرو). تم دراسة تأثير تغيير عدد القنوات في الخلايا المايكرو في الخلية الماكرو مع احتمالية الصد ولسرع مختلفة للمحطة المتنقلة كذلك تغير نصف قطر الخلية المايكرو مع احتمالية الصد وبسرع مختلفة للمحطة المتنقلة.
https://rengj.mosuljournals.com/article_32887_e644970bd8b9c330a59aaa21f8db6c33.pdf
KEYWORDS
Microcell
Channel Selection
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
73
87
10.33899/rengj.2010.32893
32893
Sequence Generator To Derive 8-Phase Variable Reluctance Stepper Motor
موّلد الإشارات لسوق محرّك الخطوة نوع الممانعة المغناطيسية المتغيرة ولحد 8- أطوار
Taha A. Al-Sabbagh
1
Kamil G. Salih
2
Abstract
Literature survey indicates that the design of sequence generator is considered for a few number of control sequences of stepper motor. In our research a new circuit is built in a simple design for generation of all required sequences up to eight phases for Variable Reluctance (V.R.) stepper motor .This circuit must be followed by a power drive circuit to achieve the power requirement of the stepper motor. In case of getting a certain sequence , these data must be given to the system ; number of phases, number of 1st energized phases, type of sequence (full step or half step mode) and finally the direction of rotation, hence the system in response will generate the required sequence. Some papers previously used SSI & MSI circuits to build the sequence generator ,but in this paper an LSI (EPROM) circuit as well as SSI & MSI circuits are used to get minimal design with less components. The paper includes a brief description of the fundamentals of sequences controlling the stepper motor, the detailed proposed circuit description and samples of experimental results with an appendix illustrating a complete map of the EPROM which is used to store all required sequences.
الخلاصـــة لقد تناولت بعض البحوث السابقة تصميم موّلد الإشارات لمحرّك الخطوة ولعدد محدود من المتواليات .. في حين تناول هذا البحث تصميم دائرة الكترونية وبأسلوب بسيط لتوليد كافة المتواليات الخاصة بالتحكم بمحرك الخطوة نوع الممانعة المغناطيسية المتغيرة ولحد ثمانية أطوار. يلحق بهذا النظام دائرة مسوّق لتوفير الاحتياجات اللازمة لتشغيل الملفات الخاصة بالمحرك. ان عملية الحصول على متوالية محددة لمحرك الخطوة تتم من خلال اعطاء البيانات المطلوبة للنظام من ناحية عدد اطوار المحرك , عدد الاطوار التي سيتم تفعيلها أولا", نوع المتوالية و الاتجاه المطلوب للدوران حيث ستقوم الدائرة بإخراج مجموعة المتواليات المطلوبة لأجل تشغيل وفحص المحرك المطلوب . سبق واستخدمت الدوائر المتكاملة من نوع SSI و MSI في بحوث سابقة من اجل الحصول على المتواليات المطلوبة, أما في هذا البحث فقد استخدمت الدوائر المتكاملة من نوع LSI إضافة إلى الدوائر المتكاملة السابقة لجعل الدائرة أكثر بساطة وبأقل عدد من الدوائر المتكاملة.. لقد تضمن البحث مقدمة لشرح اساس عمل محرك الخطوة مع الرسوم المطلوبة وشرح تفصيلي للدائرة الالكترونية المقترحة ونماذج من النتائج المختبرية إضافة إلى ملحق يوضح خارطة الذاكرة الكاملة ( EPROM ) المستخدمة لخزن كافة المتواليات المطلوبة.
https://rengj.mosuljournals.com/article_32893_23ac9d3f4d27d18d9b6a0a4295bc1c0a.pdf
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
88
93
10.33899/rengj.2010.32898
32898
DESIGN OF COMPELEMENTARY RING ARRAY ANTENNA
تصميم هوائي مصفوفة الحلقة المتممة
Dr. Eanass U. T. Al-Shabkhoon
1
Abstract
The objective of work is to find the scale of ring array antenna for localizing field intensity at certain focal point. The study is interested in comparison between focusing by setting a scale factor of array antenna to cohere (synchronize) waves of electric field when reaching focal point, and focusing by compensating phase differences that was initiated from ray length differences between waves reaching focal point. Isotropic sources are used for simulation. These sources are distributed along a circular ring, each ring of array rings is complement with the previous rings, that means it has a phase complement to a complete cycle ( ).
Keywords: Antenna, Ring, Array, Focusing, Near field
تم العمل في البحث الحالي على إيجاد أبعاد هوائي المصفوفة الحلقي لغرض تركيز الأشعة عند نقطة محددة, حيث أن إهتمام الدراسة ينصب على المقارنة بين التركيز عن طريق و ضع أبعاد محددة لمصفوفة الهوائيات تؤدي إلى تزامن وصول موجات المجال الكهربائي نقطة البؤرة و التركيز عن طريق تعويض فرق الطور الناشئ عن إختلاف أطوال مسار الموجات الواصلة نقطة البؤرة. تم إستخدام المصادر النقطية لغرض النمـﻨ جة. وزعـت هـﻨه المصادر على حلقات دائرية الشكل كل حلقة من حلقات المصفوفة متممة لسابقتها من حيث البعد أي أن لها فرق طور متمم لدورة كاملة ( ).
https://rengj.mosuljournals.com/article_32898_5780aabb05ad8bd029414ef590b4aacc.pdf
KEYWORDS
ring
Array
Focusing
Near field
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
94
106
10.33899/rengj.2010.32902
32902
IMAGE STEGANOGRAPHY BASED CURVELET TRANSFORM
اخفاء المعلومات داخل الصور بالاعتماد على التحويل (CURVELET)
AHMED FREIDOON FADHIL
1
ABSTRACT
This paper proposes a new image steganography scheme in order to hide a secret data in cover image uses the transform domain to increase its robustness and security. Curvelet transform is the new member of the evolving family of multiscale geometric transforms. Since it represents edges better than Wavelet, Curvelet transform offers an effective solution to the problems associated with image steganography using Wavelets and DCT (Discrete Cosine Transform). In this paper we were testing four different steganographic methods. The Radon Transform used in this paper for encoding the secret image to increase security. The software used in this paper is (Matlab V 7.0.4). The results obtained are in accordance with the expected predictions of the existing theory of Curvelet transform.
الخلاصة هذا البحث يقترح مخطط جديد لاخفاء البيانات السرية داخل الصور باستعمال تحويل المجال لزيادة المتانة والأمن. التحويل (Curvelet) عضو جديد للعائلة الناشئة للتحويلات الهندسية متعددة القياس . ولان التحويل (Curvelet) تقوم باسترجاع الحافات افضل من ال(Wavelets) فانها تعرض حل فعال للمشاكل المرتبطة بفن اختزال الصور باستعمال التحويلات (Wavelets) والتحويل (DCT). هذا البحث يختبر اربعة طرق مختلفة لفن الاختزال. ان التحويل (Radon) ايضا استخدم في هذا البحث لتشفير الصورة المراد اخفاءها لزيادة الامن. ان البرنامج المستعمل في هذا البحث هو (Matlab V 7.0.4). ان النتائج التي تم الحصول عليها جاءت متطابقة مع التنبؤات المتوقعة لنظرية التحويل (Curvelet) الحالية.
https://rengj.mosuljournals.com/article_32902_7e356aa0bcf24e56da33dad83bba0048.pdf
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
107
122
10.33899/rengj.2010.32906
32906
Enhanced Performance of FH Detection System Using Adaptive Threshold Level
تحسين أداء منظومة كشف إشارة القفز الترددي باستخدام مستوى عتبة متكيف ذاتيا
Ammar Abdul-Hamed Khader
1
Abstract
This work investigates the evaluation performance of detection system for Frequency Hopping (FH) signals based on Fast Fourier Transform (FFT) with proposed decision circuit based on Adaptive Threshold Level (ATL), where the threshold level changes its value automatically without manual intervention depending on the estimated values of (SNR) in the channel, the level will be high when the noise is high and vice versus. A comparison in evaluation performance were made with a conventional mode where the decision circuit based on Manually Change Threshold Level (MCTL) done by the detector according to its observation on sensing the Signal to Noise Ratio (SNR). The results shows that the proposed mode (adaptive) is give best results for probability of detection PD and probability of false alarm PF comparing with the (Manually Change). Also the results of (adaptive) are compared with that theoretical computation and gives a very small error for high noise while vanish for low noise.
Keyword: Frequency Hopping, Adaptive Threshold Level, Manually Change Threshold Level
الخلاصةهذا البحث يتناول دراسة تقييم أداء منظومة كشف إشارة القفز الترددي المعتمدة في أساس عملها على طريقة تحويل فورير السريعة FFT والمتبوعة بدائرة اتخاذ قرار مقترحة تعمل على تغيير مستوى العتبة بشكل تلقائي من دون تدخل المستلم وذلك وفقا للتخمين الذاتي المستمر لقيمة الضوضاء المضافة على الإشارة بسبب القناة حيث يرتفع المستوى بارتفاع قيمة الضوضاء وينخفض بانخفاضها. لقد تم فحص وتقييم الأداء مقارنة مع نموذج تقليدي تكون دائرة اتخاذ القرار فيه ذات مستوى عتبة يجب تغييره يدويا من قبل المستلم تبعا لملاحظاته عن تحسس تغير قيمة الضوضاء في القناة. من خلال النتائج العملية تبين أن النموذج الأول المقترح (ذاتي التغيير) أفضل من الثاني (يدوي التغيير) من حيث احتمالية الكشف PD واحتمالية التنبيه الكاذب PF. كما تم مقارنة نتائج النموذج المقترح مع النتائج النظرية وكان الفرق بسيط جدا عند قيمة ضوضاء عالية ويتلاشى الفرق عند الضوضاء المنخفضة.
https://rengj.mosuljournals.com/article_32906_6b162279854c9ad3d14e83e1f1f20d6a.pdf
Keyword
Adaptive Threshold Level
Manually Change Threshold Level
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
123
136
10.33899/rengj.2010.32909
32909
Re-design punch and die of the laboratory pharmaceutical tablet press machine
اعادة تصميم الخرامة والقالب لماكنة مختبرية صيدلانية تستخدم لاغراض كبس الحبوب
Ramiz Saeed Matty Samarjy
1
Abstract
This research represents an attempt to solve a problem introduced by Ninevah drug factory to increase the out put of one of its laboratory machine located in research sector .
First of all, thinking was for selection a suitable material of punches and die compatible with the surrounding environments of different drug powders as they represents corrosive agents to the metal that in touch .Beside that this material primarly must be capable of being machined to manufacture the required design, Also it is capable to be heat treated after manufacturing .
Second ,we should redesign the punch and die with the same surrounding spans limitation but with increasing the number of used punches and redistributing them in a suitable manner in its restricted die, and manufacturing punches with a different sizes (7, 9, 7.9,10.3,12.53 )mm in diameter as the factory demand taking into account the concave and convex of pair of punches to create the mirror shape of tablet after pressing is completed . All that will be done must give the standardized weight , size and optimum compressibility according to the certificate of the quality control unit.
Keywords: punch , die , tablet , powder.
الخلاصةهذا البحث يمثل محاولة من اجل تطوير ماكنة مختبرية تستخدم لاغراض كبس الحبوب الصيدلانية او الدوائية عائدة للشركة العامة للصناعات الدوائية في نينوى / قسم البحث والتطوير .بادى الامر كان التفكير باختيار المعدن المناسب لكل من الخرامة والقالب والذي يتلائم مع البيئة المحيطة من انواع المساحيق الدوائية المختلفة باعتبارها عوامل تساعد على التاكل للمعدن الذي سوف يكون باتصال اواحتكاك معها، اضافة الى ان المعدن المختار يمكن تشغيلة بسهولة من اجل تحقيق التصميم المطلوب وكذلك يمكن اجراء المعاملات الحرارية اللازمة له بعد التصنيع. المحور الثاني ينصب على اعادة تصميم الخرامة والقالب ضمن الابعاد المحددة للماكنة نفسها ولكن بزيادة عدد الخرامات واعادة توزيعها بالشكل المناسب ضمن شكل القالب الاصلي للماكنة، ومن ثم تصنيع خرامات بابعاد قطرية (7،9،7.9،10.3 و12.53 ملم) حسب متطلبات الشركة اخذين بنظر الاعتبار التحدب والتقعر لكلا زوجي الخرامة العلوي والسفلي لاعطاء هذا التشكيل للحبة بعد اكمال كبسها وفي النهاية فان المنتج يجب ان يحقق المواصفة المطلوبة من حيث الوزن والانضغاطية المناسبة والذي يمثل اهم جزء من محاور هذة الدراسةالكلمات الدالة ( خرامة ، قالب ، حبة ، مسحوق)
https://rengj.mosuljournals.com/article_32909_4c2c57fe8ccb12232ee52bfa822a405e.pdf
KEYWORDS
die
tablet
powder
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
137
151
10.33899/rengj.2010.34688
34688
Improvement and Modelling of the Knelson Concentrator
تحسين وعمل موديل رياضي لجهاز المركِز نوع نيلسون
Lokman Aziz AbdulKareem
1
Abstract
The Knelson concentrator is a centrifugal separator which was originally and successfully designed for extracting free gold particles. Despite of its wide range of applications, the exact concentration mechanism of the device is not fully understood.
The purpose of this research was to determine the optimum parameters and improve the performance of knelson concentrator by investigating the effects of artificial porous beds and pulsed water jackets on the performance of the device.
Artificial bed consists of glass beads of range 1.5-2 mm diameter have been used. It was found that two techniques can improve the performance of the batch Knelson concentrator. The experimental work showed that improvement ratio of concentrator was increased about 1.55 for flow rate 8 l/m compared with no bed for the same flow rate. In addition, the improvement ratio was increased about 1.25 when pulsed water was used.
Another purpose of this work was to develop mathematical model approaches to understand the fundamental mechanism of the Knelson concentrator.
In addition, two mathematical model of the Knelson concentrator have been developed.
Key words: Kneslon Concentrator, Pulsation, Porous Bed, Mathematical Model
الخلاصة جهاز المركِز نيلسون هو فاصل الطرد المركزي الذي صُمم في الاصل بنجاح في استخلاص الجسيمات الحرة للذهب .بالرغم من تطبيقاته الواسعة الانتشار في الصناعة فأن ميكانيكية و الية التركيز لجهاز ليس مفهومة بشكل كامل . لذا يهدف هذا البحث الى ايجاد افضل وامثل المعاملات لتحسين اداء الجهاز من خلال دراسة تاثيرات الطبقات المسامية الاصطناعية و الغلاف المائي متقطع التدفق على عمل اداء المركِز . وقد وجدت الدراسة بان هاتين التقنيتين لهما دور كبير في تحسين وتطوير اداء الجهاز . تم استعمال الخرز الزجاجية ذات اقطار 1.5-2.0ملم كطبقة مسامية .و ان هذه الدراسة اثبتت بان كفاءةالجهاز لفصل الجسيمات ازدادت بنسبة تحسن حوالي 1.55 عند استعمال الطبقة المسامية مقارنتا عند عدم استعمالها باستعمال نفس الظروف . وكذلك الدراسة اثبتت ازدياد كفاءة و تحسن اداء الجهاز بنسبة 1.25 عند استعمال الغلاف المائي المتقطع التدفق مقارنتا عند عدم استعمالها. و كذلك يهدف البحث الى تطوير الموديل الرياضياتي لفهم ميكانيكية و الية المركِز . وقد تم تطوير موديليين رياضيتين للجهاز .
https://rengj.mosuljournals.com/article_34688_997e7df94f2cc3a076ef02959b10590b.pdf
Key Words
Pulsation
Porous Bed
Mathematical Model
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2010-10-28
18
5
152
164
10.33899/rengj.2010.34703
34703
Flow Characteristics and Energy Dissipation Over Single Step Broad – Crested Weirs
خصائص الجريان وتبديد الطاقة فوق الهدارات مفردة الدرجة ذات القمة العريضة
Dr. Hamid H. Hussein
1
Inam A. K. Juma
2
Saleh J. S. Shareef
3
ABSTRACT
The main purpose of traditional broad - crested weir is to rise and control upstream (U/S) water level. In this study a new performance was added to this weir, by making it as an energy dissipater. In order to study the energy dissipation percent (E%), the downstream (D/S) height of the weir (12 cms U/S height) was reduced four times as 9.8,8,6and3.8cms.Thirty experiments were performed in a laboratory horizontal channel of 12 m length, 0.5 m width and 0.45 m depth for a wide range of discharge.
A mathematical model to compute theoretical coefficient of discharge (Cdth) was modified depending upon momentum equations. Experimental results gave a high validity to the computed values of the proposed model. On the other hand, three empirical non dimensional relations were obtained. The first is liner relation to estimate the ratio for D/S water head to U/S weir height (h/P1) in terms of the ratio for U/S water head to U/S weir height (H/P1). The second relation is nonlinear relation to estimate the discharge coefficient (Cd) in terms of H/P1 and the ratio of D/S weir height to U/S weir height (P2/P1). While the third relation is to estimate E% in terms of h/P1and P2/P1 with high correlation coefficients. The experimental results of the study showed that E% increased up to 46%. Furthermore, Cd was improved and gets higher values in comparison with traditional weirs.
Key words: Hydraulic structure; Broad crested weirs ; Energy dissipation.
ملخـــص إن الغرض الرئيسي من الهدار ذو القمة العريضة التقليدي هو رفع مستوى الماء والسيطرة عليه في مقدم الهدار . في هذه الدراسة تم أضافة أداء جديد لهذا الهدار من خلال تبديده لطاقة جريان الماء.ولدراسة نسبة تبديد طاقة الجريان (E% )تم تخفيض منسوب مؤخر سطح الهدار(والذي ارتفاعه في المقدم 12سم) أربعة مرات وبمناسيب3.8,6,8,9.8 سم. تم اختبار ثلاثين تجربة في قناة مختبرية افقية ذات طول 12م وعرض0.5 م وعمق 0.45 م ولمدى واسع من التصاريف. تم اشتقاق علاقة رياضية لحساب معامل التصريف النظري (Cdth) بالاعتماد على معادلات زخم الطاقة ، وأعطت النتائج المختبرية تطابق جيد مع القيم المحسوبة بهذه المعادلة . من جانب أخر تم أستنباط ثلاث علاقات وضعية لابعدية. الأولى علاقة خطية لحساب ( h/P1) بدلالة ( H/P1 ). أما العلاقة الثانية فكانت غير خطية لحساب Cd بدلالة نسبة عمق الماء مقدم الهدار الى ارتفاع الهدار في المقدم (H/P1 ) ونسبة ارتفاع مؤخر الهدار الى ارتفاع الهدار في المقدم (P2/P1 ). و كانت العلاقة الثالثة غير خطيه أيضا لحساب E% بدلالة نسبة عمق الماء مؤخر الهدار الى ارتفاع الهدار في المقدم (h/P1) ونسبة ارتفاع مؤخر الهدار الى ارتفاع الهدار في المقدم (P2/P1 ) وبمعاملات ارتباط عالية . أظهرت النتائج المختبرية لهذه الدراسة بأن E% أزدادت بنسبة 46% . بالاضافة الى ذلك تحسن أداء هذا النوع من الهدارات حيث أزدادت قيم معامل التصريف Cd مقارنة مع الهدار ذو القمة العريضة التقليدي .
https://rengj.mosuljournals.com/article_34703_57b3dd6dd02db158c9684879997d1ae2.pdf
Key Words
Broad crested weirs
Energy dissipation