eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
1
10
10.33899/rengj.2012.54148
54148
Digital Image Enhancement Using Hybrid Fuzzy Techniques Based on LabVIEW
تحسين الصور الرقمية باستخدام التقنيات المضببة المهجنة بالاعتماد على بيئة الآلات الافتراضية ( LabVIEW )
Sura Nawfal Abd alrazaaq
1
Dr. Fakhraldeen H. Ali
2
Abstract
In this paper, two LabVIEW based hybrid fuzzy filters combining fuzzy logic with simple filtering techniques for image de-noising are presented. LabVIEW is widely adopted for the design of real time systems and their realization in hardware due to the facilities available for performance simulation and measurements under different conditions. The main feature of the filters is that they try to determine the corrupted pixels using fuzzy rules and then treat them by utilizing the classical filters. To measure the performance of the designed filters, several corrupted images with Gaussian noise are processed. An objective criterion such as the Mean Square Error (MSE), and visual observation prove the effectiveness of the hybrid technique compared with the classical filters and several modern filters.
Keywords: Denoising, LabVIEW, Hybrid fuzzy filtering, Gaussian noise.
الخلاصة يقدم هذا البحث بالاعتماد على (LabVIEW) مرشح مضبب هجيني للتخلص من الضوضاء في الصور الرقمية أو تقليل تأثيرها وذلك بمزاوجة التقنيات الضبابية مع تقنيات مرشحات الصور الرقمية التقليدية, حيث أن نظام (LabVIEW ) واسع الاستخدام في تصميم أنظمة الزمن الحقيقي وتحقيقها ككيان مادي بالإضافة إلى الكيان البرمجي لإمكانياته في محاكاة أداء المنظومة المصممة وقياس أداءها تحت ظروف متباينة. إن أهم مهمة لهذا المرشح هي إيجاد النقاط الصورية المتأثرة بالضوضاء باستخدام التقنيات الضبابية ومعالجتها بعد ذلك بالاستفادة من المرشحات الكلاسيكية. لقياس أداء المرشحات المصممة تمت معالجة عدة صور تعرضت لمستويات مختلفة من الضوضاء (نوع كاوس) وبالاعتماد على المعايير الموضوعية مثل (معدل مربع الخطأ) وكذلك الرؤيا البصرية, أثبتت النتائج كفاءة الطريقة المهجنة مقارنة مع المرشحات التقليدية وعدد من المرشحات الحديثة.
https://rengj.mosuljournals.com/article_54148_7bcec6af5c5f3af73837a5585f7f173e.pdf
KEYWORDS
LabVIEW
Hybrid fuzzy filtering
Gaussian Noise
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
1
11
10.33899/rengj.2012.54127
54127
Behavior of Carbon Fiber Sheets Reinforced Concrete beam
سلوك العتبات الخرسانية المسلحة بشرائح ألياف الكاربون
Dr. Bayar J. Al-Sulayfani
1
Hala Jassim AL Hamdany
2
One of the new technologies used in increasing the bearing capacity of concrete structures is the replacing of standard (normal) reinforcement by bars made of carbon fibers making use of its properties, which gives an advantage by being antirust. In this research, an experimental study of the behavior of concrete beams reinforced with strips of carbon fibers, (one or two layers), in the tension zone of the beams, with a variable width is performed to study the behavior of the beams from the point of view of their flexural capacity, failure mode, and the effect of the friction between the concrete and the fiber strip on load failure. After conducting the tests, the results revealed that an effective contribution and an obvious role of carbon strips fiber in improving the members bearing capacity and the overall behavior, also increasing the stiffness and ductility at different rates depending on the bond stress and number of strips.
الخلاصةتعددت الطرق والوسائل لزيادة قابلية تحمل المنشآت الخرسانية فقد استخدمت تقنية حديثة تمثلت باستخدام قضبان من ألياف الكاربون كتسليح داخلي بدلاً من التسليح الاعتيادي نظراً إلى خصائصها المتعددة التي تجعلها مفضلة على معدن الحديد أهمها عدم إصابتها بالصدأ. إذ تم في هذا البحث دراسة سلوكية عتبات خرسانية مسلحة بشرائح من الألياف الكاربونية بدلاَ من قضبان التسليح. إذ تم وضع شرائح من ألياف الكاربون بطبقة واحدة وبطبقتين عند منطقة الشد لتلك العتبات وبعرض مختلف لتلك الشرائح بدل التسليح الاعتيادي لدراسة سلوكية تلك العتبات من ناحية قابلية التحمل وشكل الفشل وتأثير زيادة عدد الشرائح في زيادة الاحتكاك بين الخرسانة وشرائح الألياف الكاربونية في زيادة تحمل العتبة. بعد إجراء الفحوصات اللازمة أظهرت النتائج عن وجود مساهمة فعالة ودور واضح لشرائح الألياف الكاربونية في زيادة مقاومة التحمل للأعضاء الخرسانية وتقليل الآود إضافة إلى تحسين سلوكية العتبات وزيادة صلابة ومطيلية تلك العتبات وبنسب مختلفة تعتمد على زيادة إجهادات الربط لشرائح الألياف الكاربونية مع الخرسانة المحيطة بزيادة عدد الشرائح وتقليل عرضها، إضافة إلى زيادة عدد الطبقات المستخدمة لتلك الشرائح .
https://rengj.mosuljournals.com/article_54127_93f13b6f5273fc47941548b200c4498a.pdf
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
11
20
10.33899/rengj.2012.54151
54151
Design of Fractional Order PID Controller Based on Genetic Algorithms
تصميم مسيطر تناسبي تكاملي تفاضلي كسري المرتبة بالاعتماد على الخوارزمية الجينية
Emad A. Al-Sabawi
1
Dr. Mazin Z. Othman
2
Abstract
Fractional Order Proportional-Integral-Derivative (FOPID) controller is based on integration and differentiation of non-integer order. It is usually denoted by (0 < µ < 1 and 0 < λ < 1) . In this work the gain values of the proportional, Integral, and derivative (i.e ) as well as the values of µ and λ are obtained using Genetic Algorithms (GAs).The tuning procedure is based on the principle of model reference control. Illustrative example is presented in which FOPID controller is designed and compared with Integer Order PID (IOPID) ones. It was shown that FOPID controllers gave more freedom in faithfully following the dynamics of the reference model.
Key Words: Fractional order, PID tuning rules, Genetic Algorithms, Model reference control.
. تم تقديم مثال توضيحي صمم فيه مسيطر نوع FOPID وتم مقارنته مع مسيطر تناسبي تكاملي تفاضلي صحيح المرتبة (IOPID) . هذه المقارنة وضحت أن المسيطر نوع FOPID يعطي حرية تصميمية لزيادة دقة تتبع النظام لديناميكية المرجع النموذج.
https://rengj.mosuljournals.com/article_54151_03fbdf55496e487365861487a99cb8d2.pdf
Key Words
PID tuning rules
Genetic algorithms
Model Reference Control
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
12
29
10.33899/rengj.2012.54131
54131
Behavior and Capacity of CCT Nodes Anchored By Headed Bars in Fibrous Concrete Beams
سلوك ومقاومة عقد (الانضغاط – الانضغاط – الشد) المثبتة بقضبان منتهية الرؤوس في العتبات الخرسانية الليفية
Dr. Bayar J. Al-Sulayfani
1
Abstract
In the current research, the method of reinforcing by means of "Headed Bars" reinforcement was utilized in order to study the behavior of fiber reinforced beams, then conducting a comparison study with conventionally reinforced beams without "headed bar", where by headed bars were placed at the CCT node to analyze the behavior of the node. The presence of the headed bar with regard to bearing capacity, failure mode, and anchorage length for the reinforcing bar at the tension zone. Where the presence of the headed bar will help in reducing the anchorage length necessary to bring the reinforcing steel to yield stress (fy).This is the main objective of using such head bar reinforcing. In addition the use of this reinforce enables in the reduction of cost and the congestion of reinforce as well as the hooks. Four ratios of steel fiber and three values of shear span were used in order to find out the effect of those variables on the behavior of beams with headed bars reinforce regarding :bearing capacity, deflection under single point load, shape and type of failure,….etc. It was noticed that the bearing capacity, stiffness and ductility increased with the increased of volumetric steel fiber addition, also in the presence of headed bars reinforcement when compared with conventionally reinforced beams without steel fibers. The bearing capacity reduced as the shear span length increased.
الخلاصةتم في هذا البحث استخدام طريقة التسليح بالرؤوس الحديدية (Headed bars) في دراسة سلوك العتبات الخرسانية المسلحة بالألياف الفولاذية ومقارنتها مع العتبات ذات التسليح الاعتيادي غير المدعم بالرأس الحديدي. إذ تم وضع رؤوس حديدية عند عقدة (الانضغاط – الانضغاط – الشد) (CCT Node) لتحليل سلوكية تلك العقدة عند وجود الرأس الحديدي من ناحية قابلية التحمل وشكل الفشل وطول التثبيت لقضيب التسليح الموجود في منطقة الشد. إذ ان وجود الرأس الحديدي سوف يساعد في التقليل من طول التثبيت اللازم لإيصال حديد التسليح إلى إجهاد الخضوع (fy) وهذا هو الهدف الأساسي من استخدام هذه الرؤوس. بالإضافة إلى أن استخدام هذه الرؤوس تساعد في التقليل من الكلفة وكثافة التسليح في حالة استخدام التسليح الاعتيادي وكذلك الكلاليب. في الدراسة الحالية تم استخدام أربعة نسب للألياف الفولاذية وثلاثة قيم لفضاء القص لمعرفة تأثير هذه المتغيرات على سلوكية تلك العتبات بوجود الرأس الحديدي من حيث (قابلية التحمل، الأود المقاس تحت الحمل الأحادي النقطي، شكل الفشل، نوع الفشل...... الخ). إذ لوحظ أن قابلية التحمل للعتبات الخرسانية إضافة إلى صلابة ومطيلية ومتانة تلك العتبات تزداد بزيادة نسبة الإضافة الحجمية للألياف الفولاذية وكذلك عند وجود الرأس الحديدي مقارنة بالعتبات ذات التسليح التقليدي وعند عدم وجود الألياف الفولاذية. كما لوحظ ان قابلية التحمل تقل مع زيادة طول فضاء القص.
https://rengj.mosuljournals.com/article_54131_c8896ce648f3899d90f1b69710ea016e.pdf
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
21
31
10.33899/rengj.2012.54152
54152
FPGA Implementation of Reversible Medical Image Watermarking
رقاقة البوابات القابلة للبرمجة حقليا لتنفيذ العلامة المائية وأسترجاعها للصور الطبية
Dr. Ahlam Fadhil Mahmood
1
Abstract
Medical image protection and authentication are becoming increasingly important in an e-Health environment where images are readily distributed over electronic networks.
This paper presents an FPGA implementation of reversible watermarking encoder and decoder system. The system is based on the Discrete Cosine Transform (DCT/IDCT) to embed and extract the copyright protection mark and least significant bit (LSB) technique to hide the patients’ information and then extract back the information by the owner using.
The proposed structure employs a single multiplierless 1D-DCT/IDCT block, instead of three in many existing DCT watermarking systems, which is reduce the hardware DCT part to 16.6% compared with previous proposals. The parallel hardware implementation of DCT and LSB is done in Xilinx XSC3S500 FPGA. The proposed scheme allows multi-insertions by many doctors in order to give an exact diagnosis to the patient.
portable system of the watermarking with small size and low power dissipation
Keywords: Information hiding; watermarking ; FPGA; DCT/IDCT; Least Significant Bit method.
أن حماية وتحقُّيق ملكية الصور الطبية أُصبحت مهمة جداً في بيئةِ الصحةِ إلالكترونيةِ حيث تنقل الصورِ بسهولة عبر الشبكاتِ الإلكترونيةِ. يقدم البحث نظام يستخدم البوابات القابلة للبرمجة حقليا لأدراج علامة مائية تبين ملكية الصور مع أمكانية فصل هذه العلامة مستنذ على خوارزمية جيب التمام المنفصل ومعكوسه لتضمين وأنتزاع العلامة. وتقنية البتّ الأوطئ رتبة لإخْفاء معلوماتِ عن المرضى مع أمكانية أستحصال هذه المعلومات من قبل الجهه الطبية المخولة(المالكة لنفس النظام). التركيب المُقتَرَح يَستخدمُ كتلة جيب التمام المنفصل ومعكوسه أحادي البعد بلا ضوارب بدلا من ثلاث وحدات ثنائية البعد المستخدم في العديد من أنظمة تضمين العلامة المائية, أذ خفض البناء المادي ل 16.6% مقارنة مع الأنظمة المتستخدمة جيب سابقا. أن التنفيذ المادي المتوازي للجيب تمام وتقنية البت الاوطئ طبق على رقاقة البوابات القابلة للبرمجة حقليا XC3S500.يتيح المخططُ المُقتَرَح الإدخالِ مِن قِبل العديد مِنْ الأطباءِ لكي يَصفوا تشخيصَا دقيقا َ إلى المريضِ.
https://rengj.mosuljournals.com/article_54152_78dbc9158e1699939a5bdf818efb4ab4.pdf
portable system of the watermarking with small size and low power dissipation Keywords
watermarking
FPGA
DCT
Least Significant Bit method
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
30
37
10.33899/rengj.2012.54135
54135
Effect of Compaction Pressure in the Fresh State on The Resistance of Concreteʹs Compression and Tension
تأثير ضغط الرص في الحالة الطرية على مقاومة الإنضغاط والشد للخرسانة
Samer Sami Majeed
1
Rafal Naheth Wadie
2
Abstract
This present research presents an experimental study on the behavior of the compacted concrete filled in cylindrical steel molds with dimensions of (100 mm Diameter and 200 mm Length). In this study, different compaction pressure values have been used to compact concrete mixtures, which differ in water to cement rates using electronic compression machine. Then, compression and tension strength of a concrete at the age of (28) days, under compaction pressure in its fresh state, compared with the compression and tension values of a concrete, of the same mixing rates, unexposed to pressure, in order to study the effect of compaction pressure on the concrete in its fresh state, on the compression and tension values of the solid concrete. (90) Specimens under the impact of the stresses of compression and tension at the age of (28) days have been tested and the effect of water to cement rates and the compaction pressure on the maximum resistance of the columns have been tested. The results showed, that the compaction stresses of the concrete, affect the ultimate capacity of the columns, where they increase the compression and tension resistance of the concrete at a certain limited value of subjected compaction pressure value in the fresh state, and that the mixture with (w/c = 0.45) requires the minimum value of compact pressure to produce the maximum value of concrete resistance, while the mixtures with (w/c = 0.50) and (w/c = 0.55) require higher values of compact pressure, in order to introduce higher values of concrete resistance.
الملخصالبحث الحالي يعرض الدراسة العملية لسلوك الخرسانة المضغوطة المملوءة بقوالب اسطوانية حديدية بقياس (010 ملم القطر- 020 ملم الطول). تم في هذا البحث تسليط ضغط رص بقيم مختلفة على عدة مزجات خرسانية تختلف فيما بينها بنسبة الماء إلى السمنت بواسطة جهاز ضغط الكتروني ثم مقارنة قيم الإنضغاط والشد للخرسانة بعمر (28) يوم والتي كانت معرضة لضغط رص في الحالة الطرية مع قيم الإنضغاط والشد لخرسانة بنفس نسب المزج غير معرضة للضغط لدراسة تأثير ضغط الرص على الخرسانة في الحالة الطرية على قيم الإنضغاط والشد للخرسانة المتصلبة .. تم فحص (90) نموذج تحت تأثير إجهادات الإنضغاٍط والشد وبعمر (28) يوما ً. تم دراسة تأثير نسبة الماء إلى السمنت وضغط الرص على المقاومة القصوى للأعمدة. أظهرت النتائج بأن إجهادات الرص للخرسانة تؤثر على المقاومة القصوى للأعمدة حيث تؤدي إلى زيادة مقاومة الشد والإنضغاط للخرسانة عند حد معين من قيمة ضغط الرص المسلط في الحالة الطرية وإن الخلطة ذات نسبة ماء إلى سمنت (0.45) تحتاج إلى أقل قيمة لضغط الرص لتعطي أعلى قيمة لمقاومة الخرسانة، في حين أن الخلطات الأخرى ذات نسبة ماء إلى سمنت (0.5 ، 0.55 ) تحتاج إلى قيم أعلى لضغط الرص لتعطي قيم عليا لمقاومة الخرسانة.
https://rengj.mosuljournals.com/article_54135_055549949c63d9f2dc6f267b53f832a0.pdf
Key Words
compaction
ultimate capacity
axial load behavior
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
32
46
10.33899/rengj.2012.54153
54153
Performance Analysis of Single-Multiplier Digital Sine-Cosine Generators
تحليل أداء مولدات الجيب والجيب تمام الرقمية أحادية المضرب
Jassim M. Abdul-Jabbar
1
Noor N. Qaqos
2
Abstract
In this paper, second order structures satisfying single-multiplier digital sine-cosine generators are derived analytically, resulting in four different realizations. Some important characteristics of these generator structures, like total harmonic distortion percentage (THD%), frequency error ( and frequency resolution are defined and examined as performance measures. The four generator realizations are simulated using Matlab7.0 program. The simulation results show that better performance (THD% and are very low or negligible) can be obtained for these realizations by using 32 bits to represent the single-multiplier coefficient and other the outputs of arithmetic operations. The rounding-off method is applied as a quantization process after multiplication process. A comparison is made between one of the best-derived structures and other two recent structures implemented in previous researches. The comparison results indicate that better performance measures can be achieved from the proposed realization for the single-multiplier digital sine-cosine generator.
Keywords: Digital sine-cosine generators, Look-up Table (LUT), CORDIC, Harmonic Distortions, frequency errors, frequency deviation.
: : في هذا البحث, تم اشتقاق تركيب من المرتبة الثانية تمثل مولدات الجيب والجيب تمام الرقمية أحادية المضرب ونتج عنه تحقيقاً لأربعة نماذج مختلفة. إن بَعْض الخصائصِ المهمةِ لهذه المولّدِات، مثل نسبة التشويهِ المئويةِ الكليّةِ للتوليف (THD%) وخطأ الترددِ ( ودقة الترددِ قد تم تعرّيفها وتجريبها كأدوات تقِيس. لتحقيق التراكيب الأربعة للمولّدات استعملت المحاكاة ببرنامجMatlab 7.0 .وأظهرت نَتائِج المحاكاةَ بأنّ الأداءِ الأفضلِ (قيم THD%و منخفضة أَومعدومة) يُمْكِنُ أَنْ يُحْصَلَ عليه لهذه التراكيبب استعمال 32 بتلتَمْثي لكل من معاملِا لمضرب الوحيدِ وجميع نواتجِ العملياتِ الحسابيةِ الأخرى. إنّطريقةَ التَدوير قد طبقت في عملية التكميم بعدعمليةِ الضربِ. وعملت مقارنة بين أحد أفضل التراكيبِ المُشْتَقّةِ مع تركيبين آخرينِ طبّقا في البحوثِ السابقةِ. تُشيرُ نَتائِجُ المقارنةَ إلى أنّ قياسات الأداءِ الأفضل يُمْكِنُ أَن نحصل عليها مِنْ أفضل تركيب مُقتَرَحِ لمـولدات الجيب والجيب تمام الرقمية أحادية المضرب.
https://rengj.mosuljournals.com/article_54153_4386c2e608ca701d8a318db93a1cd2d5.pdf
KEYWORDS
cosine generators
Look
up Table
CORDIC
Harmonic Distortions
frequency errors
Frequency deviation
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
38
49
10.33899/rengj.2012.54139
54139
Coefficient of Discharge for Labyrinthine Side Weir
معامل التصريف للسد الغاطس الجانبي المتعرج
Dr. GhaniaHayawi
1
Azza Al-Talib
2
Mena Al-Sawaf
3
Abstract
The main objective of this investigation is to be obtain the coefficient of discharge for labyrinthine side weir. 24 labyrinthine side weirs were constructed and built in upstream of side channel of a 15 cm width and 30 cm depth and 2 m long with constant horizontal bed. The weir height were varied three times as 9cm, 12 cm, and 15 cm and each height tested for four different angels of the weir crest ( ). The weirs were used with direction and opposite direction of flow with different discharges.
From the analysis of results it was found that the labyrinthine side weir with small height and small angle is more efficient when put in the direction of flow.
Two general expressions were obtained to estimate the coefficient of discharge in terms of the hydraulic parameters in direction and opposite direction of flow, also it was found that the rate between length of weir to the depth of flow is the most effective parameter.
Key words: side weir, discharge coefficient
الخلاصةيهدف البحث إلى إيجاد معامل التصريف للسد الغاطس الجانبي المتعرج. وقد صنع لهذا الغرض 24 نموذج لسدود غاطسة متعرجة مثلثة موضوعة في مقدم قناة جانبية ( بعرض 15 سم وعمق 30 سم وطول 2 م ) وبقعر أفقي ثابت. وقد تم تغيير ارتفاعات نماذج السدود لثلاث مرات (9 سم و12 سم و15 سم ) وتغيير زوايا رأس السدود الغاطسة لأربع حالات ( ) كما وضعت السدود الغاطسة في حالتين مع وعكس اتجاه الجريان كمتغيرات هندسية للنماذج وبإمرار تصاريف مختلفة عليها. ومن تحليل النتائج وجد أن السدود الغاطسة الأقل ارتفاعاً وذات الزاوية الصغيرة كفاءتها أكبر في إمرار التصريف باتجاه الجريان، وتم إيجاد علاقتين لمعامل التصريف بدلالة المتغيرات الهندسية والهيدروليكية للنماذج محل الدراسة باتجاهيها مع وعكس الجريان كما وجد أن نسبة طول حافة السد إلى عمق الجريان هو المؤثر الأكبر في كلا العلاقتين.الكلمات الدالة : السد الغاطس الجانبي ، معامل التصريف
https://rengj.mosuljournals.com/article_54139_df7238fa658b8d9915457545c0086e79.pdf
Key Words
discharge coefficient
الكلمات الدالة
معامل التصريف
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
47
59
10.33899/rengj.2012.54155
54155
Performance Analysis of Wireless Network Control Systems Using Different Controllers
تحلیل أداء أنظمة شبکات السیطرة اللاسلکیة باستخدام مسیطرات مختلفة
Ena’am F. Khuder
1
Sura N. Abd alrazaaq
2
Omar abd al-kareem
3
Abstract Recently Wireless communication technologies have strongly adopted in real-time industrial environments. The increasing availability of products and solutions based on the IEEE 802.11 standard make this kind of communication technology becomes more cost effective in distributed control systems. This paper describes real time control application over Wireless Local Area Network (WLAN) in Ad hoc mode using a Virtual Instrument VI environment (LabVIEW). Particularly the delay time in such networks is considered as a critical factor that has a significant effect on the system response time characteristics such as rise time(Tr), settling time(Ts). So in this paper we discussed the effect of using different controllers (such as P, PID, Fuzzy, …) on the overall system performance. The experimental measurements show that the using of fuzzy controller gives best results where it can minimizes the effect of the network delay on the system behavior as much as possible. Keywords: UDP/IP, WLAN, Remote real-time control, PID, Fuzzy.
فی الوقت الحاضر أُعتمِدت تقنیات الاتصال اللاسلکی بقوة فی البیئات الصناعیة, حیث إن ازدیاد تواجد المنتجات والحلول المعتمدة على المقیاس IEEE 802.11 جعل هذا النوع من تقنیة الاتصال ذا کلفة قلیلة عند استخدامه فی أنظمة السیطرة الموزعة. یصف هذا البحث تطبیق منظومة سیطرة فی الزمن الحقیقی عبر الشبکة اللاسلکیة المحلیة (WLAN ) باستخدام بیئة الآلات الافتراضیة (LabVIEW ). بصورة عامة یعتبر زمن التأخیر فی أی شبکة عاملا حرجاً ذو تأثیر مهم على خصائص استجابة النظام مثل زمن الارتفاع (Tr) وزمن الاستقرار ( (Ts وغیره من الخصائص, ولهذا تم فی هذا البحث مناقشة تأثیر استخدام مسیطرات مختلفة (مثل المسیطر التناسبی, المسیطر التناسبی التکاملی التفاضلی والمسیطر المضبب) على أداء النظام الکلی, إذ أظهرت القیاسات العملیة إن استخدام المسیطر المضبب أعطى أفضل النتائج حیث قلل تأثیر تأخیر الشبکة على تصرف النظام بأکبر قدر ممکن.
https://rengj.mosuljournals.com/article_54155_29804752200b7355df1f1738fb0627c6.pdf
KEYWORDS
WLAN
Remote real
time control
PID
fuzzy
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
48
59
10.33899/rengj.2012.54142
54142
The Hydraulic Characteristics of Tigris River at Mosul City
الخصائص الهيدروليكية لنهر دجلة في مدينة الموصل
T. A. Chilmiran
1
I. A.I. Al-Hafith
2
Kh. I. Othman
3
Abstract
In this research the hydraulic characteristic of seventy seven cross sections along 21 km of Tigris River at Mosul city were studied. These cross sections were surveyed and their bed and water surface elevations were measured.
The river at the studied reach have a different morphology and includes three different shapes (meander part braided part and straight part). The results of the study showed that the river at study reach has an average water surface slope equal of 4.7*10-4. The straight part of the river reach has uniform and regular hydraulic characteristic compared to other river parts. The river have wide cross sections, the values of T/D varies between 50-1500 and due to reduction in discharge there was a great reduction in flow depth and the river was receded and river reach was narrowed than before . The deepest part was extended beside the right bank from upstream of Ninevah Bridge to downstream of Al-Horriya Bridge. Application of HEC-RAS Model showed that the model can simulate the hydraulic characteristics of river under different flow condition. Data obtained from the model was used to find empirical relations between (average velocity, average depth, cross section area, Top width and discharge with the stage.
Key Words: Tigris River, Mosul City, Hydraulic Characteristics, HEC-RAS Model.
الملخص تم في هذا البحث دراسة الخصائص الهيدروليكية لمقطع طولي من نهر دجلة في مدينة الموصل بطول 21 كم وبواقع 77 مقطع عرضي. المقاطع العرضية تم مسحها وتحديد منسوب سطح الماء عندها بهدف ايجاد الخصائص الهيدروليكية عند كل مقطع. ان النهر ضمن منطقة الدراسة يتحوي على ثلاثة اجزاء مختلفة جزء منحني وجزء متفرع وجزء مستقيم. بينت نتائج الدراسة ان معدل انحدار سطح الماء لنهر دجلة في منطقة الدراسة كانت تساوي 4.7*10-4 وان النهر ذا خصائص هيدروليكية منتظمة على طول الجزء المستقيم من النهر ولكن في الاجزاء التي تحتوي على انحناءات وجزرات فان هذه الخصائص لاتبقى منتظمة. ان مقطع النهر بشكل عام عريض رغم انحسار الماء الى مجرى ضيق بسب نقصان التصاريف حيث تراوحت قيمT/D لمجرى النهر مابين 1500-50 وان اعمق منطقة (مستمرة) تمتد من مقدم جسر نينوى الى مؤخر جسر الحرية وعلى جهة الضفة اليمنى . النتائج المستحصلة من تطبيق النموذج الرياضي HEC-RAS بينت الى امكانية النموذج في تمثيل حقل الجريان وبشكل كفوء والتعرف على خصائص النهر عند مواقع مختلفة وتحت ظروف جريان متعددة. النتائج المستحصلة من النموذج الرياضي تم استخدامها في ايجاد علاقات وضعية تربط بين المتغيرات معدل السرعة, معدل العمق , مساحة الجريان, عرض ومنسوب سطح الماء والتصريف مع المنسوب ولعدة مقاطع على طول مجرى النهر.
https://rengj.mosuljournals.com/article_54142_39e2198cd8fa8f7c3afb7630ea042cb2.pdf
Key Words
Mosul City
Hydraulic Characteristics
HEC
RAS Model
RAS
الكلمات الدالة
مدينة الموصل
الخصائص الهيدروليكية
النموذج الرياضي
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
60
73
10.33899/rengj.2012.54145
54145
Modeling Effect of Irrigation Water quality Frequency with difference Leaching requirement on the salts accumulation and yield for sorghum
نمذجة تأثير مناوبة نوعية مياه الري بمتطلبات غسل مختلفة على تجمع الأملاح والإنتاجية لمحصول الذرة البيضاء
Omar Mkdad Abdul Guny Mahmood
1
A Computer model is made in (MATLAB) language to study the effect of irrigation water salinity levels 20,15,12 dS/m irrigation applied by continuous irrigation with saline water and alternant irrigation by different methods (pure irrigation : saline two irrigation),(pure irrigation : saline irrigation) and (pure two irrigation : saline irrigation). Pure irrigation represents Tigris River salt water 0.47dS / m. Each method used the Leaching requirements (0, 0.05, 0.1, 0.15, 0.2, 0.25, and 0.3), The model depends on the principle of balancing water and salt. The computer model has been applied to the sorghum crop; a summer crop which endures medium salinity. The results show that the accumulation of salt varies according to the differences in irrigation style. The amount of salts accumulated in the soil increased by using the continuous irrigation, while the use of alternant irrigation led to reduced accumulation of salts and thus led to increased production. The amount of decrease in the accumulation of salts depends on the method of alternant irrigation and leaching requirements used. Mathematical equations have been formulation to find out the increase or decrease in the real Yield and relative evaporation transpiration as a result of the influence of the amount of salt water and pure water additives under the conditions and limitations of the study area
Keywords: Leaching, salinity, continuous irrigation, alternant irrigation, Yield
المستخلصتم بناء أنموذج حاسوبي بلغة(MATLAB) لدراسة تأثير كل من مستويات ملوحة ماء الري 20,15,12dS/m بأسلوب الري المتبع على تجمع الأملاح في التربة و الإنتاجية: الري المستمر بالمياه المالحة و الري المتناوب بطرائق وأساليب مختلفة من الإرواء (رية نقية : ريتان مالحة) و( رية نقية : رية مالحة) و(ريتان نقية : رية مالحة) والرية النقية تمثل ملوحة ماء نهر دجلة 0.47dS/m ، ولكل أسلوب استخدم فيه متطلبات غسل (0, 0.05، 0.1، 0.15، 0.2، 0.25، 0.3)، يعتمد عمل الأنموذج الحاسوبي على مبدأ الموازنة المائية والملحية. وقد تم تطبيق الأنموذج الحاسوبي على محصول الذرة البيضاء وهو محصول صيفي ويعتبر من المحاصيل متوسطة التحمل للملوحة. بينت النتائج ان التراكم الملحي يتباين باختلاف أسلوب الري المستخدم، وان كمية الأملاح المتراكمة في التربة تزداد باستخدام الري المستمر، في حين استخدام الري المتناوب يؤدي إلى خفض تراكم الأملاح وبالتالي يؤدي هذا إلى زيادة الإنتاج وان كمية النقصان في تراكم الأملاح تعتمد على أسلوب الري المتناوب ومتطلبات الغسل المستخدم ، كما تم صياغة معادلات رياضياتية لإيجاد الزيادة أو النقصان للإنتاج الحقيقي والتبخر- نتح النسبي نتيجة تأثير كمية المياه المالحة والنقية المضافة تحت ظروف ومحددات منطقة الدراسة.مفتاح الكلمات: غسل، ملوحة، ري مستمر، ري متناوب، إنتاجية
https://rengj.mosuljournals.com/article_54145_c4635bf7ed14a9eae98b2156009c1f1b.pdf
KEYWORDS
salinity
continuous irrigation
alternant irrigation
Yield
مفتاح الكلمات
ملوحة
ري مستمر
ري متناوب
إنتاجية
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
60
68
10.33899/rengj.2012.54156
54156
Design and Fabrication of Thin Film a-Si/Al2O3 Infrared Filter
تصميم وتصنيع مرشح الأشعة تحت الحمراء نوع a-Si/Al2O3
Dr. Khalid Khaleel Mohammad
1
Mr. Saad Gazai
2
ABSTRACT
Long-wavelength infrared filter operated at various temperature are critical for imaging applications. In this paper anew type of infrared filter is investigated, this infrared filter uses a crystalline silicon substrate coated with multi layers of aluminum oxide (AL2O3) and amorphous silicon (a-Si) to produce the multi layers thin film infrared filter a-Si/AL2O3 operating in the range (8-14)um. Amorphous silicon is used in this paper due to its high refractive index, while AL2O3 due to its low refractive index material. The a-Si/ AL2O3 thin film structure were designed using the Thin Film Design software (TF Calc 3.5.6 version). The simulated results obtained shows that the transmittance of the a-Si/ AL2O3 infrared filter with 19 layers is about 90% for (8-12.5) µm wavelength, while it is about 95% for 47 layers for (8.25-13.25) µm wavelength. The investigated filter was fabricated using vacuum evaporation process and the results obtained were comparable with the simulated one. The fabricated a-Si/ AL2O3 filter is compared with the Ge/ZnS infrared filter and it is found that the results is comparable but the cost of the fabricated filter is small compared to the Ge/ZnS filter.
Keyword: Infrared Filter, Silicon, Aluminum Oxide.
الخلاصةيعتبر مرشح الموجة تحت الحمراء والذي يعمل بدرجات حرارة مختلفة من العناصر المهمة في التطبيقات الصورية. تم في هذا البحث اقتراح نوع جديد من مرشح الموجة تحت الحمراء مكون من طبقة أساسية من مادة السيلكون المتبلور ومرسب عليها طبقات عديدة من مادة أوكسيد الألمنيوم ومادة السيلكون العشوائي التركيب (a-Si) وذلك لتكوين مرشح الموجة تحت الحمراء ضمن الحزمة (8-14) m. تم استخدام مادة السيلكون العشوائي في البحث بسبب معامل انكساره العالي بينما تمتاز مادة أوكسيد الألمنيوم بمعامل انكسار واطئ ، وتمت عملية التصميم باستخدام البرنامج (TF calc 3.5.6 version) حيث تم الحصول على مرشح مكون من 19 طبقة وذات نفاذية مقدارها 82% للطول الموجي (8-12.5) m ، بينما كانت النفاذية بحدود 90% باستخدام 47 طبقة للطول الموجي (8-13.75) m. تم تصنيع المرشح المقترح باستخدام جهاز التبخير الفراغي وكانت النتائج قريبة جداً من نماذج التمثيل بالحاسوب. كذلك تمت مقارنة النتائج مع المرشح المكون من مادة الجرمانيوم ومادة كبريتيد الخارصين وكانت النتائج متقاربة ولكن مع كلفة قليلة للمرشح المقترح مقارنة مع المرشح المصنع من مادة الجرمانيوم ومادة كبريتيد الخارصين (Ga/ZnS).
https://rengj.mosuljournals.com/article_54156_566be0a1538f860a8120be885c405767.pdf
Keyword
Silicon
Aluminum Oxide
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
69
85
10.33899/rengj.2012.54157
54157
Impact of Downlink Distributed and Adjacent Subcarrier Permutation Modes on the Performance of Mobile WiMAX System in ITU-R Ped. B Channel with Obtaining Optimum Cyclic Prefix
تأثير تباديل الحاملات الفرعية الموزعة والمتجاورة للاتجاه النازل على اداء نظام الواي ماكس المتنقل في قناة من نوع ITU-R Ped. B مع ايجاد القيمة المثلى للبادئ الدوري
Safwan E. Abdul Fatah
1
Dr. Sami A. Mawjoud
2
Abstract
Mobile WiMAX is one of the candidate technologies for 4G wireless systems, promising high data rates and affluent multimedia services. The mobile WiMAX standard (IEEE802.16e-2005)is based on Orthogonal Frequency Division Multiple Access (OFDMA), which allows a very efficient use of bandwidth in a wide frequency range, this is due to the fact that OFDMA uses multi-channel OFDM approach and provides subcarrier access in the time and the frequency domains.
In this paper the impact of downlink distributed (FUSC, PUSC) and adjacent (AMC) subcarrier permutation modes used in mobile WiMAX system are investigated using simulation under various modulation and coding schemes (link speeds)with the support of optimum value of the Cyclic Prefix (CP) for the OFDMA symbol duration. The results are expressed in terms of the maximum achievable throughput and operating distance from base station in pedestrian multipath fading channel (ITU-R Ped. B at 3Km/h speed) under a UDP-based application (video streaming), which is the proper application for multimedia services. The results show the optimum cyclic prefix valve for the FUSC, PUSC and AMC subcarrier permutation modes to achieve the best system performance, also the results show differences in PER performance atvarious modulation and coding schemes for the three subcarrier permutation modes (FUSC, PUSC and AMC). These differences in performance are exploited in the present work to show the best threshold SNR to switch from link speed to another link speed in terms of throughput and operating distance.
Key words: IEEE802.16e-2005, OFDMA, FUSC, PUSC, AMC, ITU-R Ped. B channel, PER.
الملخصيعتبر نظام الواي ماكس المتنقل احد انواع التكنلوجيا المرشحة للجيل الرابع اللاسلكي والذي يتميز بمعدل نقل بيانات عالي وخدمات غنية بالوسائط المتعددة. يستند نظام الواي ماكس المتنقل ذي المعيار (IEEE 802.16e-2005) على مبدا التردد المتعامد المقسم حسب الطلب (OFDMA) والذي بدورة يستثمر عرض الحزمة بشكل كفوء من خلال تقسيم القناة وتوفير اختيار الحاملات الفرعية (subcarriers) في مجال الزمن والتردد.في هذا البحث تم باستخدام المحاكاة تحليل تأثير تباديل الحاملات الفرعية من النوع الموزع والمتجاور المستخدم في نظام الواي ماكس المتنقل تحت تاثير انواع مختلفة من التضمين والتشفير وحسب القيمة المثلى للبادئ الدوري (cyclic prefix) في زمن الرمز. وقد تم اعتماد النتائج من حيث اعلى throughput واقصى مسافة عن محطة الارسال يمكن تحقيقه في قناة المشاة ذات الخفوت متعدد المسارات (ITU-R Ped. B. وبسرعة 3Km/hour). وباستخدام تطبيق من نوع UDP لملائمته لخدمات الوسائط المتعددة. وقد بيت النتائج القيمة المثلى للبادئ الدوري في زمن الرمز عند تباديل الحامل الفرعي FUSC و PUSC و AMC لتحقيق الاداء الافضل للنظام. كذلك بينت النتائج ان هنالك فروقات في اداء النظام من ناحية الـ PERلتباديل الحاملات الفرعية FUSC و PUSC و AMC في حالات التضمين والتشفير المختلفة، حيث تم استثمارها في هذا العمل لإيجاد افضل قيمة SNR للتحويل من سرعة ارتباط الى اخرى من حيث الـ throughput ومسافة العمل.
https://rengj.mosuljournals.com/article_54157_1a82d3b5453063c62333cc48680ed803.pdf
Key Words
OFDMA
FUSC
PUSC
AMC
ITU
R Ped
B channel
PER
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
86
102
10.33899/rengj.2012.54158
54158
Nonlinear Analysis of Reinforced High Strength Concrete Deep Beams With Openings
التحليل غير الخطي للعتبات الخرسانية المسلحة العميقة عالية المقاومة بوجود الفتحات
Baraa Jabbar Mahmood
1
Abstract
The objective of this study is to estimate the influence of web openings in reinforced concrete deep beams by using nonlinear finite element analysis. Concrete represented by isoperimetric eight nodes, serendipity plane stress, elements. The reinforcement treated as embedded elements and considered as elastic perfectly plastic. New constitutive models to simulate concrete material suggested by means of a nonlinear regression analysis of many experimental data by using SPSS 16 – statistical program. Strain hardening approach was employed to model the compressive behavior of high strength concrete. In tension two models were used to model high strength concrete in the pre – peak and post peak states. A smeared fixed crack approach of cracked concrete in tension is assumed. Three variables included concrete strength, shear span – to – depth ratio and the width and depth of openings. The results indicated that the ultimate strength is remarkably decreased in deep beams with openings rather than deep beams. Experimental results for reinforced high strength concrete deep beam with openings compared with the finite element results and showed good agreement.
Keywords: Deep beam, Finite element, High strength concrete, Nonlinear analysis, Openings, New constitutive models.
الخلاصةتهدف هذه الدراسة لتخمين تأثير وجود الفتحات في العتبات الخرسانية المسلحة العميقة عالية المقاومة باستخدام التحليل غير الخطي بطريقة العناصر المحددة. تم تمثيل الخرسانة بعناصر رباعية موحدة المعملية بطريقة الاجهاد المستوي وتم تمثيل حديد التسليح كعناصر مطمورة في الخرسانة وتم اعتبارها مادة مرنة – تامة اللدونة. تم اقتراح علاقات تكوينية جديدة للتمثيل المادي للخرسانة باستخدام التحليل التراجعي غير الخطي للعديد من بيانات الدراسات العملية باستخدام البرنامج الإحصائي SPSS 16. أُستخدم تصلب الانفعالات اللدن لتمثيل الخرسانة عالية المقاومة في حالة الانضغاط. في حالة الشد أُستخدم نموذجان الاول لما قبل الحالة القصوى والثاني لما بعدها. أُفترض نموذج الشق الثابت المنتشر في الخرسانة المتشققة في حالة الشد. ثلاثة متغيرات أُخذت بنظر الاعتبار مقاومة الخرسانة، نسبة فضاء القص الى العمق الكلي وعرض وعمق الفتحات. أظهرت النتائج بأن المقاومة القصوى للعتبات العميقة تنخفض بشكل ملحوظ في حالة وجود الفتحات. تمت مقارنة نتائج الدراسات العملية للعتبات الخرسانية المسلحة العميقة عالية المقاومة بوجود الفتحات مع نتائج التحليل غير الخطي باستخدام طريقة العناصر المحددة وأظهرت توافقاً جيداً.
https://rengj.mosuljournals.com/article_54158_514f677665a6d945c16e1aaa70adb2f7.pdf
KEYWORDS
finite element
High Strength Concrete
Nonlinear analysis
Openings
New constitutive models
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
103
117
10.33899/rengj.2012.54159
54159
Influence of Concrete Mix Proportions and Curing Regimes on Density, Absorption, and Voids in Hardened Concrete
تأثير نسب المزيج الخرساني وأساليب المعالجة على الكثافة، الامتصاص والفراغات في الخرسانة المتصلبة
Omer Mohammad Abdul kreem
1
Abstract
The aim of this research is to assess the mechanical strength and durability performance of the concrete incorporating various contents of the ordinary Portland cement and w/c. Besides, it has been undertaken to study the effect of curing methods on compressive strength of the concrete as well as the physical properties, which are investigated in terms of density, absorption and volume of permeable voids as an (porosity). Many researchers consider these physical properties as an indicating signs on the permeability of the concrete, or in other words, they were as an indirect method to measure the permeability and to evaluate it.
Five mixes are prepared and tested at the age of 28 days. The concrete specimens are cured in two different methods, in the first method specimens are moist cured while in the second method the specimens are air cured at 20 ˚C and 80% relative humidity to examine the effect of curing regimes. An experimental procedure for testing the physical properties of concrete is carried out according to ASTM (C 642-97). The results of the study showed that the increase of cement content and the reduction in the w/c leads to more durable concrete because of loss of absorption and porosity characteristics, in addition to that, higher density and compressive strength. Test results also showed that the water curing method have significant effect for improving the strength and durability performance of the concrete.
Keywords: Concrete, Mix Proportion, Curing Conditions, Durability Performance, Physical Properties.
المقاومة الميكانيكية وأداء الديمومة لخرسانة حاوية على محتويات مختلفة من الإسمنت البورتلاندي الاعتيادي ونسبة (الماءالإسمنت)، إلى جانب ذلك فإن هذا البحث يشرع في دراسة تأثير طرق المعالجة على مقاومة إنضغاط الخرسانة إضافة إلى خواصها الفيزيائية المتمثلة بالكثافة، الإمتصاص وحجم الفراغات النافذة المتمثل ب(المسامية)، إذ أن الكثير من العلماء يعتبرون الخواص الفيزيائية للخرسانة مؤشراً على نفاذية الخرسانة، أو بعبارة أخرى تعتبر هذه الخواص طريقة غير مباشرة في قياس النفاذية وكذلك في تقييمها. تم تحضير خمس مزجات وإختبارها بعمر 28 يوم، إذ أن النماذج الخرسانية تمت معالجتها بطريقتين مختلفتين، تتمثل الطريقة الاولى بغمر النماذج في الماء بينما في الطريقة الثانية وضعت النماذج في الهواء بدرجة حرارة 22م˚ ورطوبة نسبية بمقدار 80% وذلك لغرض دراسة تأثير نظام المعالجة. تم الفحص وإختبار الخواص الفيزيائية حسب الخطوات العملية المثبتة في المواصفة القياسية الاميريكية ASTM C (642-97). أشارت نتائج هذه الدراسة إلى أن إزدياد محتوى الاسمنت وتناقص نسبة (الماءالإسمنت) يؤدي ذلك إلى إنتاج خرسانة أكثر ديمومة بسبب النقصان الحاصل في خواص الامتصاص وحجم الفراغات النافذة (المسامية). كما دلت النتائج أيضًا إلى أن المعالجة بالماء تملك تأثيرأً إيجابيأً في تحسين أداء المقاومة والديمومة للخرسانة.
https://rengj.mosuljournals.com/article_54159_cb3971f2d8378717c9848e9c30cd37bd.pdf
KEYWORDS
Mix Proportion
Curing Conditions
Durability Performance
Physical Properties
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
118
127
10.33899/rengj.2012.54160
54160
Stream flow Simulation and Synthetic Flow Calculation by Modified Thomas Fiering Model
نمذجة تصاريف الانهار وتخمين تصاريفها باستخدام النموذج الرياضي المحور ثوماس فيرينك
Dr. Cheleng A. Arselan
1
Abstract
In this paper , Thomas-Fiering T-F model was used twice for simulation of Khassa Chi river in Kirkuk city by using historical monthly stream flow sequences for a period (1941-2001) . A modification to Thomas-Fiering model was done by extracting the persistency from the monthly flow values of Khassa Chi river and including the regression values between the monthly values of the flow without persistence. It was concluded that Thomas-Fiering model is very suitable to simulate Khassa Chi behavior. The modified model MT-F was more capable to reverse the monthly and annual statistical parameters especially the monthly and annual standard deviation and it was more sensitive in reversing the drought times which reflects its capability in other simulation operations for variables which are suffering from drought times.
Key words :Thomas-Fiering , Persistence Simulation
الخلاصة في هذا البحث استخدم النموذج ثوماس فيرينك مرتين لنمذجة نهر خاصة جاي الجاري في مدينة كركوك حيث تم اجراء تحليل لخصائص السلسلة الشهرية المسجلة لنهر خاصة جاي والمتضمنة تصاريف النهر الشهرية للفترة(1941-2001) .تم تحديث النموذج وذلك باستخلاص الخاصية الغير العشوائية من التصاريف الشهرية وايجاد معاملات الارتباط الخاصة بين التصاريف الشهرية الخالية من هذه الخاصية . تم التوصل الى قابلية النموذج الرياضي Thomas- Fiering بصيغته المعروفة لنمذجة نهر خاصة جاي كما انه عند تحسين النموذج الرياضي تم التوصل الى معاملات احصائية شهرية وسنوية وخصوصا قيم الانحراف المعياري الشهرية والسنويةاكثر قربا من البيانات الاصلية. حيث بدا اكثر تحسسا لفترات الجفاف مما يجعله قابلا للاستخدام لعمليات النمذجة لمتغيرات اخرى مختلفة قد تعاني من فترات قحط. الكلمات الدالة : ثوماس-فيرينك الخاصية الغير العشوائية , النمذجة
https://rengj.mosuljournals.com/article_54160_ca79a1e0f5c52b3e2ae65b5893bc10c8.pdf
Key Words
Fiering
Persistence Simulation
الكلمات الدالة
فيرينك الخاصية الغير العشوائية
النمذجة
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
128
136
10.33899/rengj.2012.54161
54161
Observing the rising and falling of water level in Mosul Dam Lake using remote sensing data and Geographical Information System
مراقبة ارتفاع وانخفاض منسوب المیاه فی بحیرة سد الموصل باستخدام بیانات التحسس النائی ونظام المعلومات الجغرافیة
K.A. Ahmed
1
R.G. Thanoon
2
A.R. Abdurrahman
3
ABSTRACT Multi temporal Landsat ETM+ satellite images for the period (1986 to 2009) are used to determine the boundary of Mosul Dam Lake. Digital Image processing (Enhancement, Image Fusion and classification) applied for the input data. The output images showed the values of surface area in Km2. In order to extract the level of water a digital elevation model was combined with the output images. The (Elevation – Area – Volume) curve for Mosul Dam Lake (which depended on field measurements) used to compare the values of water level of the lake that extracted from the satellite images with digital elevation model and that one plotted on the curve. The results of this study showed an agreeable convergence between them. Keyword: Mosul dam, Remote sensing, GIS.
https://rengj.mosuljournals.com/article_54161_143226d99f2bd595d521bf8e7345f2a7.pdf
Keyword
remote sensing
GIS
eng
College of Engineering, University of Mosul, IRAQ
Al-Rafidain Engineering Journal (AREJ)
1813-0526
2220-1270
2012-08-28
20
4
137
153
10.33899/rengj.2012.54162
54162
Comparison the stresses and deflections of an isotropic and orthotropic rectangular plates with central circular hole under tension load
مقارنة الإجهادات والانحرافات في قطعتين معدنيتين مستطيلتين إحداهما موحدة الخواص والأخرى غير موحدة الخواص ذواتي ثقب مركزي تحت تأثير قوة الشد
Ahmed M. Abdullah
1
ABSTRACT
The distributions of stresses and deflection in rectangular isotropic and orthotropic plates with central circular hole under transverse static loading have been studied using finite element method. The object of this present work is to analyze the effect of D/Y ratio (where D is hole diameter and Y is plate width) upon stress distribution and deflection in plates under tension subjected to a static loading. The D/Y ratio is varied from (0.1) to (0.9). The results are obtained for four different boundary conditions. The variations of stresses and deflections with respect to D/Y ratio are presented in graphical form. The finite element formulation is carried out by using the analysis section of the ANSYS package
Keywords: Finite Element, Isotropic and orthotropic plates, Boundary conditions.
لقد تم استخدام طريقة العنصر المحدد في دراسة توزيع الاجهادات والانحرافات الحاصلة في قطعتين مستطيلتي الشكل تحتويان على ثقب مركزي من معدنين ذوي خواص غير متساوية تحت تأثير حمل شد ثابت.الغرض من هذا البحث معرفة تأثير قطر الثقب المركزي الموجود في هاتين القطعتين على تركيز الاجهادات فيها وكذلك على الانحرافات التي تحدث فيهما بسبب هذا الحمل ولكل من القطعتين.إن النسبة D/Y (قطر الثقب إلى العرض) تغيرت ما بين (0,1) إلى (0,9) وتم الحصول على النتائج لكلا القطعتان. وقد تم عرض المنحنيات الخاصة بتغير تمركز الاجهادات نسبة إلى تغيير D/Y ومناقشتها باستخدام احد برامج العنصر المحدد وهو البرنامج المسمى ."ANSYS 12"الكلمات المفتاحية : العنصر المحدد، قطع موحدة وغير موحدة الخواص، الشروط الحدية
https://rengj.mosuljournals.com/article_54162_3e910834436c6eec0b502fd4e96f1c98.pdf
KEYWORDS
Isotropic and orthotropic plates
boundary conditions
الكلمات المفتاحية
قطع موحدة وغير موحدة الخواص
الشروط الحدية