College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628The Effect Of Sulfur Waste And ABS On Asphalt Cement Propertiesتأثير فضلات الكبريت والالكيل بنزين سلفونيت على خصائص الاسفلت1102700510.33899/rengj.2011.27005ENA. T. HameedA. R. I. Al-HadidyJournal Article20110601ABSTRACT
Nineveh is one of the Iraqi provinces 400 km north Baghdad capital and having an industrial company for sulfur production. This company produces nearly 20-25% of the total production as waste materials. This research investigates the ways of recycling the sulfur waste (SW) in solving the higher cost problem coming from import of waterproofing materials and presents information on the program and laboratory test data. Materials used in test program included 40/50 asphalt cement, Alkyl benzene sulfonate (ABS) and sulfur waste (SW). Five SW contents 0, 1, 3, 5 and 7%, and 1% of ABS in terms of asphalt cement by weight were used. Tests including physical properties, compatibility, storage stability, aging properties, temperature susceptibility and water permeability were carried out in accordance with the ASTM procedure. The test results revealed that SW is a reliable material for paving asphalt cement and being readily available can be widely used in water proofing construction materials, and this offers profound engineering and economic advantages.
Keywords: Sulfur waste, Alkylbenzene sulfonate, Asphalt, Modifier, Water proofing material.الخلاصةتمتلك محافظة نينوى شركة لصناعة الكبريت. تنتج هذه الشركة ما يقارب 20 إلى 25% من الناتج الكلي كمخلفات. تتحرى هذه الدراسة عن إمكانية إيجاد وسائل لاستخدام مثل هذه الفضلات في إنتاج مواد مانعة الرطوبة وبأقل كلفة ممكنة بدلا من استيرادها من الخارج، كما تضمنت الدراسة عرض معلومات وافية عن برنامج الفحوصات المختبرية التي تم اجراؤها على المزيج المنتج والمواد الداخلة في تركيبته والمتضمنة الاسفلت ذو النفاذية 40-50, الالكيل بنزين سلفونيت والفضلات الكبريتية. استخدمت الفضلات الكبريتية بعدة نسب (5,3,1 و7% من وزن الاسفلت) مع 1% من الالكيل بنزين سلفونيت في انتاج عدة انواع من الاسفلت المستخدم كمانع رطوبة. اجريت الفحوصات الفيزياوية, التجانس, ثباتية الخزن, التقادم, تأثير الحرارة و نفاذية الماء على المزيج المنتج بموجب المواصفات الأمريكية. أوضحت الدراسة إمكانية استخدام الفضلات الكبريتية مع الالكيل بنزين سلفونيت في انتاج اسفلت رخيص الثمن يصلح لأعمال التسطيح وقطع النضوح بدلا من استيراده وبالعملة الصعبة خاصة وان هذه الفضلات متوفرة محليا.الكلمات الدالة: فضلات الكبريت: الكيل بمزين سلفونيت: اسفلت: محسنات: مواد مانعة رطوبة.https://rengj.mosuljournals.com/article_27005_cd65c87566164e3ab1b635d4721a53b5.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Graphical Method of Concrete Mix Designتصميم الخلطة الخرسانية بطريقة الرسم1122699110.33899/rengj.2011.26991ENDr. Khalid A. ZakariaMohammad Hatem MohammadJournal Article20110601The current research work caters for the possibility of arriving at a method for designing concrete mixes (job mix) using locally available materials by means of three prescribed properties of the mix as design pre-requisites, that is water content, water : cement ratio and aggregate : cement ratio of wide ranges to cover a good variety of practical mixes. The above mentioned three prescribed properties can be represented in a graphical solution manner using a trilinear diagram depending on the fact that the absolute volume of the concrete mixture consisting of three materials, cement, water and aggregate is the sum of absolute volumes of the three materials. As a result and from this representation a quadrilateral area can be formed which should include a wide range of mixes having all the prescribed properties mentioned above. The current work will consider the following main influencing parameters on the job mix:
1. Water : cement ratios between 0.35-0.84.
2. Maximum aggregate sizes of 20 and 12.7 mm.
3. Fine aggregate ranges of fine, medium and coarse (B.S 882-1992 [11])
4. Aggregate : cement ratios between 3.8-7.6.الخلاصةيتضمن البحث الحالي إمكانية الوصول إلى طريقة لتصميم الخلطات الخرسانية باستعمال مواد محلية عن طريق تحديد ثلاث خواص موصوفة مسبقاً للخلطة الخرسانية (Pre-requisite) وهي المحتوى المائي نسبة الماء إلى السمنت ونسبة الركام إلى السمنت وبمديات واسعة لتغطي أنواعاً عملية وعديدة من الخلطات.تم تمثيل هذه الخواص الثلاثة عن طريق الرسم (Graphical Method) بشكل ثلاثي الأضلاع يعتمد على مبدأ الحجم المطلق للخليط الخرساني، ويمثل مجموع الحجوم المطلقة لكل من الماء والسمنت والركام أي المكونات الرئيسة الثلاثة للخلطة. وكنتيجة لذلك سوف تحدد مساحة معينة (رباعية الشكل) ضمن الشكل الثلاثي الأضلاع والتي سوف تضم أو تحوي عدداً هائلاً من الخلطات لها الخواص الثلاثة الموصوفة مسبقاً،من بين العوامل الرئيسة المؤثرة على نسب الخلط تم اعتماد الآتي في البحث الحالي وكما يلي:1.نسبة الماء إلى السمنت تراوحت بين (0.35-0.84).2.المقاس الأقصى للركام الخشن (20.0 و 12.7 ملم).3.تدرج الركام الناعم (خشن،متوسط وناعم).4.نسبة الركام الكلي إلى السمنت تتراوح بين (3.8-7.6).https://rengj.mosuljournals.com/article_26991_eb6c62ae4d852365c84b67d9cb4c2ee1.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628A Laboratory Tool Used to Evaluate the Reflective Cracking in Overlay Asphalt Pavementعدة مختبريه لتقييم الشقوق الانعكاسية على طبقات الاكساء للطرق المرصوفة بمزيج الكونكريت الإسفلتي11252701010.33899/rengj.2011.27010ENDr. Talal H. AlmudadiAss. Prof. Dr. Ali H. AlneamiJournal Article20110601Abstract
The causes of reflective cracking can be either environmental and/or load associated. The simultaneous movements of an overlay caused by wheel loads (vertical movements), temperature changes, temperature gradients (horizontal movements) induce a complex stress state of cyclic bending tension, and shear within the overlay.
Different types of tools are used to simulate the mechanism of reflective cracking in the laboratory , in this research only the tool which simulates the effect of temperature variation (horizontal movement) is studied. Overlay Testing Equipment is constructed and tested in Iraq . All the tested samples are beams of dimensions 7.6cm width, 38.1cm length with different thickness. Three parameters are taken in this study, filler type, thickness of asphalt concrete beams and additives and their effects on the properties of asphalt concrete mix. From the results, the samples prepared by limestone as a filler give higher number of cycles than that prepared by cement, the samples of high thickness give higher number of cycles and the control sample gives best results than modified samples.
Keywords: Reflection Cracking, Asphalt Concrete Overlay, Filler, Overlay Tester.المستخلصإن سبب ظهور الشقوق الانعكاسية إما يكون بسبب التغيرات البيئية (تفاوت درجات الحرارة) أو بتأثير أحمال المركبات مما سيولد اجهادات بنوعين احدهما بالحركية الأفقية على الطبقة التحتانية التي تؤثر على طبقة الاكساء الجديدة بنفس الحركة والأخرى توليد حركة عمودية نتيجة الأحمال فوق مناطق المفاصل والشقوق, عند وجود هذين التأثيرين و تجاوزهما قوة تحمل الطبقة الجديدة سوف تنعكس المفاصل والشقوق على طبقة الاكساء الجديدة.أجهزة وعدد مختلفة تستخدم لمحاكاة ميكانيكية حدوث الشقوق الانعكاسية في المختبر. في هذا البحث تم تصنيع واستخدام أول جهاز في العراق لمحاكاة الحركة الأفقية التي تتولد بسبب التمدد والتقلص( نتيجة التغيرات الحرارية) لطبقات الرصف بالكونكريت-الأسمنتي أو الكونكريت-الإسفلتي.النماذج المفحوصة كانت متوازي مستطيلات بإبعاد(7.6سم عرض × 38.1سم طول × أسماك مختلفة). درس تأثير ثلاث عوامل المادة المالئة (fillers) , سمك طبقة التأهيل (الاكساء) واستخدام بعض المضافات (additives) ومدى تأثيرها على خواص مزيج الكونكريت-الإسفلتي . تم اعتماد نظام عدد الدورات المسلطة (Number of cycles) اللازمة لكسر النموذج (فشل النموذج) كمعيار لصلاحية وأفضلية النموذج.أظهرت النتائج أن النماذج المعدة من مطحون حجر الكلس كمادة مالئة أعطت عدد أعلى من الدورات المسلطة من تلك المصنوعة من الاسمنت , في حين أن النماذج ذات السمك الأعلى أعطت نتائج أعلى من ذات السمك الأقل. بينما النماذج التي لم يتم إضافة أي مواد أخرى للمزيج القيري أعطت نتائج أفضل من التي أضيفت إليها بعض المضافاتhttps://rengj.mosuljournals.com/article_27010_e615b1e147f72c223ccb770f275208b7.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628The Use Of Vacuum Pressure For Water Desalinationأستخدام ضغط التفريغ في معالجة المياه المالحة13212699310.33899/rengj.2011.26993ENLayth Abdul-Aleem AlannazJournal Article20110601Abstract
The research focuses on water desalination by distillation process under condition of vacuum pressure. The distillation unit was elevated over the ground surface then water was sucked from it. The water was boiled at temperatures below (100)oC as a result of reaching the absolute pressure to the vapor pressure values of water at these temperatures. The distillation unit was elevated at (6.27-7.15-8.25)m over ground surface, so that the absolute pressures exerted were (37.54-27.76-18.21)kPa respectively and the boiling points were (78-72-62) oC respectively. At each elevation of the distillation unit, different values of temperature were applied on the saline water samples (with same concentration and volume). The results indicated increasing in evaporation rate with increased elevation from ground level and with increasing of the applied temperature. This is linked with increasing in evaporation energy as a result of (boiling heat flux) increasing with the depression in absolute pressure and with increasing in temperature. The average increasing in evaporation rate was (6.78)cm3/hr for each (kPa) depressing in absolute pressure and (7.41) cm3/hr for each (oC) rising in temperature. The condensation tube was designed for each boiling and evaporation process depending on mounting the condenser at atmosphere. The design was affected by the variation in temperature and pressure applied.
Key words: Desalination, Distillation, Vacuum pressureالملخصيركز البحث على معالجة المياه المالحة بتطبيق عملية التقطير بأسلوب يعتمد على توليد ضغط تفريغ عليها إذ يتم رفع وحدة التقطير إلى مستوى أعلى من مستوى سطح الأرض وسحب الماء منها فتؤدي هذه العملية إلى جعل الماء يغلي في درجات حرارية اقل من (100)درجة مئوية وذلك نتيجة لوصول الضغط المطلق إلى ضغط بخار الماء عند تلك الدرجات. تم رفع وحدة التقطير إلى ثلاث مستويات تبعد (6.27-7.15-8.25)م عن سطح الأرض فكانت الضغوط المطلقة المسـلطة على الماء المالح (37.54- 27.76-18.21)كيلوباسكال على التوالي ودرجات الغليان (78-72-62)درجة مئوية على التوالي. جرى إخضاع نماذج من المياه المالحة بنفس التركيز والحجم إلى درجات حرارية مختلفة عند كل مستوى. أظهرت النتائج ارتفاع معدل التبخير مع زيادة الارتفاع عن مستوى سطح الأرض ومع زيادة الدرجة الحرارية المسلطة من المصدر, وقد ارتبط ذلك بارتفاع طاقة التبخير نتيجة لزيادة (تدفق حرارة الغليان) مع الانخفاض الحاصل في الضغط المطلق ومع الزيادة في درجة الحرارة المسلطة. كان متوسط الزيادة في معدل التبخير (6.78)سم3/ساعة لكل كيلوباسكال انخفاض في الضغط المطلق و(7.41) سم3/ساعة لكل درجة مئوية زيادة في درجة الحرارة. كما تم تصميم أنبوب التكثيف اللازم لكل عملية غلي وتبخير تم إجراءها اعتمادا على مبدأ امرار المكثف في الهواء الجوي. كما تم بحث مدى تأثير درجة الحرارة والضغط المطلق المسلطين على طول أنبوب التكثيف.https://rengj.mosuljournals.com/article_26993_d75d9867966769826c470c07bb374465.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Study of the Misalignment of the Rotary Kiln Relative to Carrying Roller Center in Cement Factories on the Stress in Bearingsدراسة تأثير انحراف الفرن الدوار عن محور العجلات الحاملة في معامل الأسمنت على الإجهادات في المحامل22332699710.33899/rengj.2011.26997ENDr. Sabah. M. J. AliMr. Ahmed M. AbdullahJournal Article20110601ABSTRACT:
Misalignment problem is considered as one of the most important and common repeated problems in rotary kiln in meanly all of cement factories. This will lead to generation of vibration and extra loads on bearing of the carrying rollers. Also a non-uniformity can occur in distribution of applied load on all the surface of the bearing which being concentrated on one or two sides of the bearing surface, and finally leads to falling the fire lining.
The present research work is concentrated on the analysis of stresses generated on bearing of the carrying rollers of the rotary kiln in new Hammam Al-Alil factory. In addition the effect of misalignment is shown on stresses distribution and it's concentration. This is important for the bearing design and those who work in bearing maintenance in this factory.
The "(ANSYS 9.0)", which uses a finite element technique, had been utilized in this program. This is a very efficient and accurate tool in stress analysis for many cases. The stresses had been calculated for the assumed cases.
The results showed clearly that the stress distribution and concentration on the bearing is altered with misalignment for each case.
Keywords: Misalignment, Rotary kiln, Techniques , ANSYSالخلاصـة:تعد مشكلة عدم المحاذاة في الأفران الدوارة (Rotary Kilns) من أهم المشاكل التشغيلية الشائعة والمتكررة الحدوث في معظم معامل الاسمنت إذ تؤدي إلى توليد اجهادات وأحمال إضافية على محامل العجلات الحاملة, والى عدم انتظام توزيع الحمل المسلط على سطح المحمل بتركزه على جانب واحد أو جانبين من جوانب المحمل .وبالتالي إلى سقوط البطانة النارية الموجودة داخل جسم الفرن.يتمحور هذا البحث حول تحليل الإجهادات المتولدة على محامل العجلات الحاملة للفرن الدوار في معمل سمنت حمام العليل الجديد, ودراسة تأثير التغير في حالة عدم المحاذاة في توزيع هذه الإجهادات وتركزها نظرا لما لدراسة تمركز الإجهادات من أهمية كبيرة بالنسبة للعاملين في مجالات تصميم المحامل وصيانتها, إذ يتوقع أن يبدأ تلف في مادة المحامل عند مناطق تركز الإجهادات. أُستُخدِم في هذا البحث برنامج (ANSYS 9.0) بوصفه أداة فاعلة ودقيقة في تحليل الإجهادات ولحالات متعددة, إذ تم اختيار نوع المعدن وتقسيم النموذج إلى الشرائح المختارة له وإجراء عملية التقييد وتسليط الحمل, وأخيرا الحصول على قيمة الإجهادات ولكل حالة من حالات عدم المحاذاة المفروضة.بعد عرض النتائج المستحصلة من البرنامج, يمكن ملاحظة التغير الذي يحدث على توزيع الإجهادات والانفعالات وقيم الانزلاق والتداخل والإزاحات وأماكن تركزها على سطح المحمل مع حالات عدم المحاذاة.https://rengj.mosuljournals.com/article_26997_c3de001e86aaccff42c9f8eb084238c2.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Studying of the Gypsiferous Soil Suction Using Filter Paper Techniqueدراسة إجهادات المص للترب الجبسية باستخدام تقنية ورق الترشيح26362701210.33899/rengj.2011.27012ENAsaad M. A. AL-OmaryJournal Article20110601Gypsiferous soils have specific feature under its suction studying. These soils contain salt solution that affects on the suction components at high water content levels. This paper investigates soil suction of three types of gypsiferous soils namely: Al-Muhallabeia, Al-Jarin, and Al-Slmanii using filter paper technique. The investigated soils were located in Nineveh province (400 Km north Baghdad capital) and found to have a gypsum content of about 35, 23, and 6%, respectively.
This study includes some factors (water content, gypsum content, and clay content) that affect the soil suction for gypsiforous soils. The effect of gypsum content on slope of the relationship between soil suction with pF unit and water content was examined.
The results revealed that there is a linear relationship between soil suction and its water content for three studied soils. Both total and matric suction values increase as soil water content decrease. On the other hand, the difference between total and matric suction values increase with soil samples water content. The soil clay content has more effect on gypsiferous soil suction than its gypsum content.
Key words: Gypsiferous soil, Soil suction, Total suction, Matric suction, Gypsum contentالخلاصةتمتلك الترب الجبسية ميزات خاصة عند دراسة اجهادات المص لها، بسبب امتلاك تلك الترب على محاليل ملحية والتي تؤثر على مكونات إجهادات المص عند المستويات العالية من المحتوى المائي للتربة. هذه الدراسة تأخذ بنظر الاعتبار دراسة إجهادات المص لثلاث انواع من الترب الجبسية الواقعة في محافظة نينوى (400 كم شمال العاصمة بغداد): المحلبية، والجرن، والسلماني، والتي لها محتوى جبسي تقريباً (35، 23, 6) % على التوالي. تتضمن هذه الدراسة بعض العوامل (المحتوى المائي، المحتوى الجبسي، المحتوى الطيني) التي تؤثر على إجهادات المص للترب الجبسية باستخدام تقنية ورق الترشيح. أخيرا، درس تأثير المحتوى الجبسي على ميل العلاقة التي تربط بين مص التربة بوحدة pF والمحتوى المائي.أظهرت النتائج بان هناك علاقة خطية بين مص التربة ومحتواها الرطوبي للترب الثلاث المدروسة. وان قيم المص الكلي والنسيجي تزداد مع نقصان المحتوى المائي، من الناحية الاخرى ،التغاير بين قيم المص الكلي والنسيجي تزداد مع زيادة المحتوى المائي وان تاثير المحتوى الطيني اكبر من تاثير المحتوى الجبسي على قيم مص الترب الجبسية.https://rengj.mosuljournals.com/article_27012_e856b285c263d56945d18bf09c299658.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Modeling Effect of Saline Water With deficient Irrigation levels on Soil Salinity and Yield for Maizeنمذجة تأثير المياه المالحة بمستويات ري ناقصة على ملوحة التربة والإنتاجية لمحصول الذرة34452699910.33899/rengj.2011.26999ENDr . A. A. A. AL-TalibO. M. A. G. MahmoodJournal Article20110601Abstract
Computer model is made in (MATLAB) language to study the effect of deficit irrigation with saline water on the salts accumulation in soil and the effect extent of the lack of water and the salts accumulation on yield. The Model has been applied on summer crop, Maize, and it relies on the principle of balancing water and salt. The Model are uses the basic variables entered in the irrigation (climate data, crop type, soil type, and the rate of moisture depletion , irrigation level, the initial soil salinity and salinity of irrigation water). The results obtained from the program are (daily potential and adjusted Evapotranspiration, daily balance of water and salt, the quantities of irrigation water and Perfusion appointment, The rate of change of concentration of salts before and after Perfusion, electric conductivity of saturation extract at Slaking, calculating the relative defect of seasonal yield). study show when using a little amount of irrigation water we have a little salt accumulation in the soil, but the salt accumulation at the end of the season depends on the gross depth of irrigation water added . Low levels of irrigation led to lower proportional yield in the event that the impact of water shortage was bigger than the impact of irrigation water salinity on productivity, and vice versa. Formulation of mathematical equations to find the relative yield and seasonal actual Evapotranspiration because of irrigation water salinity and water shortage, under the condition of study area and determinants.
Keywords: deficit, salinity, Yield, depletion, Evapotranspirationالمستخلص تم بناء أنموذج حاسوبي بلغة(MATLAB) لدراسة تأثير الري الناقص بمياه مالحة على تجمع الأملاح في التربة ومدى تأثير نقص المياه وتجمع الأملاح على الإنتاجية. وقد تم تطبيق الأنموذج على احد المحاصيل الصيفية وهو الذرة. يعتمد الأنموذج على مبدأ الموازنة المائية والملحية. حيث إن الأنموذج يستخدم المتغيرات الأساسية المؤثرة على الاستهلاك المائي (البيانات المناخية، ونوع المحصول، ونوع التربة، ونسبة الاستنزاف الرطوبي، ومستوى الإرواء، الملوحة الأولية للتربة وملوحة ماء الري). أما النتائج التي تم الحصول عليها من الأنموذج فهي (التبخرـ نتح الكامن والمصحح اليومي، والموازنة المائية والملحية اليومية، وكميات ماء الري وموعد الإرواء، ومعدل تغير الأملاح قبل الإرواء وبعده، ومعدل التوصيل الكهربائي لمستخلص الإشباع عند الإرواء، بالإضافة إلى النقص النسبي للإنتاج الموسمي). بينت النتائج انه كلما كانت مستويات الإرواء قليلة كلما كان تجمع الأملاح في التربة قليلاً، إلا ان تجمع الأملاح في نهاية الموسم تعتمد على كمية ماء الري الموسمي المضاف. وان انخفاض مستويات الإرواء تؤدي إلى انخفاض الإنتاج النسبي في حالة كون تأثير نقص المياه اكبر من تأثير ملوحة ماء الري على الإنتاجية ، والعكس صحيح. كما تم صياغة معادلات رياضياتية لإيجاد الإنتاج النسبي والتبخر- نتح الحقيقي الموسمي نتيجة ملوحة ماء الري ونقص المياه تحت ظروف ومحددات منطقة الدراسة.https://rengj.mosuljournals.com/article_26999_a6a64ae9cf1e621f93d04f5e8117a886.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Effect of Partial Replacement of Sand with Limestone Filler on Some Properties of Normal Concreteتأثير مسحوقِ حجر الكلس كبديل جزئي من الرمل على بعض خصائص الخرسانة الاعتيادية37482701410.33899/rengj.2011.27014ENRana Burhan Abdurrahman AlshahwanyJournal Article20110601Abstract
In recent years, there is a growing interest in the use of crushed sand obtained from limestone quarries in some countries where river sand is not widely available. Besides, the demand for aggregates to produce concrete is still high while natural resources decrease. The fines content in limestone is usually high (particles with a size of 0.15-0.7 mm) which can affect concrete properties in an either positive or negative way. Studies on aggregate containing fine materials are vitally important. However, little work has been done so far on the effect of fines in crushed sand on the properties of concrete.
This paper examines the influence of limestone filler in sand on concrete properties, which include workability of fresh concrete (slump test method), compressive and tensile strength, unit weight, and ultrasonic pulse velocity. Six concrete mixtures containing different ratios of limestone filler (0, 10, 20, 30, 40, 50) % sand replacement were used while maintaining a constant water/cement ratio. The results proved that limestone filler replacing sand up to 20% without adversely affecting concrete strength.الخلاصةفي السنوات الأخيرة، أصبح هنالك اهتمام متزايد من قبل بعض البلدان لاستخدام مسحوق الرمل الناتج من سحق حجر الكلس حيث الرمل النهري غير متوفرَ بشكل واسع، إضافةً إلى الطلب المستمر والمتزايد بمستوى عالي على الركام لإنْتاج الخرسانة بينما مصادر الطبيعة في تناقص مستمر. عادة ما تكون نسبة المواد الناعمة في مسحوق حجر الكلس عالية (جزيئات يتراوح مقاسها بين 0.15-0.07 ملم) و يمكن أن تؤثر على خصائص الخرسانة بصورة ايجابية أو سلبية.يمكن القول ان الدراسات حول الركام الحاوي على مواد ناعمة إجمالاً مهمة بشكل حيوي ومع ذلك فالقليل من البحوث تناولت تأثير المواد الناعمة في مسحوق الرمل على خصائص الخرسانة. تضمن البحث تأثير مسحوق حجر الكلس في الرمل على خصائص الخرسانة التي تضمنت فحص قابلية التشغيل للخرسانة الطرية (فحص الهطول) ومقاومتي الانضغاط والشد الانشطاري ووحدة الوزن وسرعة الموجات فوق الصوتية من خلال صب ستة مزجات خرسانية ذات نسب مختلفة لمسحوق حجر الكلس تضمنت (0،10،20،30،40،50)% مستبدلة من الرمل مع الحفاظ على نسبة الماء إلى الإسمنت ثابتة. أثبتت النتائج انه يمكن استبدال الرمل بمسحوق حجر الكلس لغاية نسبة 20% وبدون أي تأثير سلبي على المقاومة.https://rengj.mosuljournals.com/article_27014_08dbdae8ee5edbe763a680ee38057834.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Dual Twins in Architectureالتوائم الثنائية في العمارة46682700210.33899/rengj.2011.27002ENFarhan Awad Jasim Al-TaiDr. Hassan M.H. KasimJournal Article20110601Abstract
Dual twins in architecture have been widely spread since the middle 20th century in various parts of the world; however, the unclear and comprehensive view about the nature and reasons of the emergence of such phenomena is still not established. The current study attempts to determine the nature and reasons of the emergence of such phenomena clearly and comprehensively. In order to examine the theoretical background of this phenomena, concept of twins in language, philosophy, biological and medical sciences is reviewed in addition to examining principles of dual architectural and artistic composition and the priors of dual twins in history of architecture. Thus, the two hypothesis of the study are formed where the first states that dual twins are either identical or fraternal, related or not related materially with each other. The second indicates that unity of design is the reason behind the emergence of dual twins leading to aesthetics, integrity within the urban context.
The study has made a deductive survey of 27 of dual twin buildings around the world. The study concluded that both the hypothesis are largely met but not absolutely. There are identical and fraternal twins but not materially related with each other and characterize by a complete structural and functional independence with their visual interrelation forming both of them as one dual composition. Concepts of architectural composition aiming at breaking monotony and presenting the new were the most influential in the emergence of dual twins in architecture in addition to other functional, rational, urban and environmental causes.
Keywords: dual twins - dualism.الملخصانتشرت ظاهرة التوائم الثنائية في العمارة منذ منتصف القرن العشرين بانحاء مختلفة من العالم. والمعرفة لحد الآن غير واضحة وغير شاملة حول طبيعة ومبررات نشوء تلك الظاهرة. ويهدف البحث الحالي الى محاولة تحديد طبيعة ومبررات نشوئها بشكل واضح وشامل. ولدراسة الخلفية النظرية للظاهرة تم الرجوع الى دراسة مفهوم التوائم في اللغة والفلسفة والعلوم البايولوجية والطبية، ودراسة مبادئ التكوين المعماري والفني الثنائي، ودراسة أوليات ظاهرة التوائم الثنائية من تاريخ العمارة. فتشكلت فرضيتا البحث الرئيسيتان المرتبطتان بهدفه. تشير الفرضية الاولى الى ان التوائم الثنائية اما ان يكونا متماثلين أو غير متماثلين، مرتبطين مادياً مع بعضهما أو غير مرتبطين، وتشير الفرضية الثانية الى ان المبرر لنشوء التوائم الثنائية هو الوحدة في التصميم والتي تؤدي الى جماله وكماله واندماجه في سياقه الحضري. وأجرى البحث دراسة استقرائية لعينة من المباني التوائم الثنائية المنفذة في انحاء مختلفة من العالم والمكونة من 27 مبنى. وتوصل الى ان فرضيتيه قد تحققتا بنسبة كبيرة ولكنها ليست مطلقة، فهناك توائم ثنائية متماثلة تماماً وتوائم غير متماثلة بارتباط مادي بينهما او استقلال كامل انشائي ووظيفي احدهما عن الآخر مع بقاء الارتباط البصري الذي يقدمهما كتكوين ثنائي واحد. وكانت مفاهيم التكوين المعماري وقيمه التشكيلية الطامحة الى كسر الرتابة وتقديم الجديد والمثير هي المبرر الاكثر تأثيراً في نشوء التوائم الثنائية في العمارة بالاضافة الى مبررات أخرى وظيفية وعقلانية وحضرية وبيئية.https://rengj.mosuljournals.com/article_27002_447be865f8a8a1aa004c6ef63c204579.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Design and Fabrication of the Single Polepiece Magnetic Electron Lens of Truncated Cone Polepiece Shapeتصميم وتصنيع عدسة الكترونية مغناطيسية أحادية القطب ذات قطب مخروطي الشكل ناقص49542701810.33899/rengj.2011.27018ENMuna A. Al-KhashabAbdullah I. MostafahIssam I. IsmailJournal Article20110601Abstract
The magnetic electron objective lens is of a great importance which limit the resolving power of the electron microscope.
The present work investigates the objective focal properties of a single polepiece magnetic electron lens of truncated cone polepiece shape of the selected geometrical dimensions for practical applications. The lens has been fabricated consist of cast shield made of mild steel combined with exciting isolated cooper coil of 500 turns.
The theoretical and experimental results presented the magnetic flux density distribution and the objective focal properties of the lens, in mode of operation when the direction of incident electrons beam facing the lens back plate of the lens.
Moreover, the theoretical and experimental results are in a good agreements.
Keywords: electron optics, magnetic lens fabrication, design of magnetic lens, objective properties, low voltage scanning electron microscope.الملخصتعد العدسة الالكترونية المغناطيسية الشيئية ذات أهمية كبيرة في المجهر الالكتروني حيث تحدد قدرة تحليله. تناول البحث الحالي استقصاء الخواص البؤرية الشيئية لعدسة الكترونية مغناطيسية ذات قطب أحادي مخروط ناقص الشكل، وتم اختيار أبعادها الهندسية لتلائم التطبيق العملي. صنعت العدسة الالكترونية بغلاف متكون من سبيكة الفولاذ والملف المهيج لها يتكون من (500) لفه من سلك نحاسي معزول. تم الحصول على نتائج توزيع كثافة الفيض المغناطيسي والخواص البؤرية الشيئية للعدسة نظرياً وعملياً، في نظام التشغيل لسقوط الحزمة الالكترونية بالاتجاه المقابل للوح الخلفي للعدسة.فضلا عن ذلك تمت مقارنة النتائج النظرية والعملية وأظهرت أن هنالك توافقاً جيداًhttps://rengj.mosuljournals.com/article_27018_9f014626c5f1747f602232bcf1dbcb29.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628The effects of Reduced Temperature and Pressure on Natural Convection in Rectangular Cavity Filled with a Supercritical Water: a Benchmark Numerical Solutionتأثير درجة الحرارة والضغط المنقصين على انتقال الحرارة بالحمل الطبيعي داخل تجويف مستطيل مملوء بالماء الخفيف(SCW)55682702210.33899/rengj.2011.27022ENYounis M. NajimJournal Article20110601Abstract
In this paper, natural convection heat transfer of supercritical water in rectangular enclosure has been investigated in various values of reduced temperature (0.955 1.205) and pressure (1.2 2.0). The right and left sides of enclosure considered to be isotherm with a temperature difference of , while the lower and upper sides of the enclosure was thermally insulated. The width of enclosure is 0.004m. Calculations were performed for Rayleigh number ( ), Prandtl number ( ). The values of Ra and Pr are governed by the fluid temperature and pressure which are controlled by reduced temperature( ) and reduced pressure ( ). Streamlines, isotherms and mean Nusselt numbers are presented. It is found that the temperature distribution and flow field are affected by the reduced temperature and pressure. The results also show that the maximum Nusselt number could be obtained at the same specification of geometry and temperature difference increases as the pressure reach the critical pressure.
Keyword: Natural convection, supercritical Water, reduced temperature and pressureألخلاصةفي هذا البحث، تم دراسة تأثير درجة الحرارة والضغط المنقصين على انتقال الحرارة بالحمل الطبيعي داخل تجويف مستطيل مملوء بالماء الخفيف (SCW)، حيث اشتملت الدراسة على مدى من درجات الحرارة المنقصة بينما كانت القيم للضغط المنقص ، وقد اعتبرت درجة حرارة جانبي التجويف الأيمن والأيسر ثابتتين وبفرق درجات حرارة مقداره 0.0323K، أما الجانبان العلوي والسفلي فقد فرضا على أنهما معزولين عزلاً حرارياً. وفقا لذلك فان قيم رالي كانت وقيم براندتل ، يتم احتساب الخواص الفيزيائية للماء الخفيف عند درجة الحرارة والضغط ، وبالتالي فان المتغيرين الرئيسيين في هذه الدراسة هما درجة الحرارة والضغط المنقوصين ( ). حيث أظهرت النتائج تأثراً كبيراً في توزيع درجات الحرارة وجريان الماء الخفيف (SCW) وانتقال الحرارة بهذين المتغيرين. كما بينت النتائج أيضا أن القيم القصوى لعدد نسلت تزداد كلما اقترب ضغط الماء الخفيف(SCW) من الضغط الحرج تحت نفس الظروف.https://rengj.mosuljournals.com/article_27022_023c7dfe289db9154d88062780c60633.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628 Study of Heat Storage in Shallow Fluidized Bedsدراسة الخزن الحراري في الطبقات المميعة الضحلة69752702510.33899/rengj.2011.27025ENBurhan Mahmood Ahmad Al-AliJournal Article20110601Abstract
This paper presents the theoretical analysis and experimental study of the performance of a shallow fluidized bed as a storage system for thermal energy.
River sand is used as a bed with different height values and compressed heated air as an external fluidizing.
A bundle of finned tubes is used as a heat exchanger immersed in the bed for the extraction of stored energy from the bed.
Empirical correlations are offered by experimental work, which show the relations between the instantaneous local temperature within the bed and time as a function of both bed height and inlet air velocity.
Keywords: Heat, Transfer, Fluidized Beds, Heat Storage,.المستخلصيقدم هذا البحث دراسة عملية وتحليل نظري لأداء مبادل حراري يعمل بالطبقات المميعة الضحلة عند خزن الحرارة فيه.استخدم الرمل النهري وبارتفاعات مختلفة كطبقة مميعة ، والهواء المضغوط الساخن كمميع خارجي.استخدمت في البحث حزمة من الأنابيب المزعنفة كمبادل حراري مغمور داخل الطبقة من اجل حساب كمية الحرارة المخزونة في الطبقة. كما يعرض البحث مجموعة من المعادلات التجريبية والتي تم التوصل أليها من خلال الجزء العملي والتي تربط بين درجة الحرارة الموضعية والوقت اللازم لشحن المنظومة بدلالة ارتفاع الطبقة وسرعة الهواء.https://rengj.mosuljournals.com/article_27025_817cc2a48923c48ecfe5167df99dc325.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628FPGA based Reconfigurable 2D FFT Systemمنظومة FPGA قابلة لاعادة التشكيل لتنفيذ خوارزمية FFT ثنائية الابعاد76882702610.33899/rengj.2011.27026ENShefa A. DawwdAhmad F. Al-allafJournal Article20110601Abstract
This paper develops a system level architecture for implementing a cost-efficient, FPGA-based reconfigurable two dimensional (2D) FFT system. The adopted approach considers both the hardware cost (in terms of FPGA resource requirements), and performance (in terms of throughput). These two extremes are optimized based on using run time reconfiguration, double buffering technique, shared Dual Ported RAM (DPRAM) modules and the “hardware virtualization” to reuse the available processing components. The system employs two one Dimensional (1D) FFT processor each with sixteen reconfigurable parallel FFT cores. Each core represents a 16 complex point parallel FFT engine. Thus the architecture supports transform length of 256X256 complex points, as a demonstrator to the design idea, using fixed-point arithmetic and has been developed using radix-4 butterfly architecture. The simulation results that have been performed using VHDL modeling language and ModelSim software shows that the full design can be implemented using single FPGA platform requiring about 50,000 Slices.
Keywords: 2D Fast Fourier Transform Radix-4. Run Time Reconfigurationألخلاصة في هذا البحث تم تطوير معمارية بمستوى النظام جديدة لماكنة FFT قليلة الكلفة لمعالجات الزمن الحقيقي باستخدام دوائر ال FPGA . التصميم المقترح يأخذ بنظر الاعتبار تحقيق اقل الكلفة (بدلالة متطلبات موارد ال FPGA ) واعلى انجاز (بدلالة ال throughput) وذلك من خلال استخدام خاصية اعادة التشكيل في زمن التنفيذ و خاصية الخزن المزدوج والذاكرات المشتركة ثنائية الاطراف وخاصية اعادة الاستخدام للمكونات المادية لدوائر ال FPGA . المنظومة المقترحة تستخدم 32 وحدة FFT متوازية قابلة لاعادة التشكيل مقسمة الى مجموعتين كل مجموعة (16 وحدة) تشكل معالج FFT لتنفيذ خوارزمية FFT احادية البعد. كل من هذه الوحدات هي عبارة عن معالج FFT متوازي بطول 16 نقطة مركبة . لذا فأن المعمارية المقترحة تستطيع تنفيذ خوارزمية FFT ذات البعدين بطول 256X256 نقطة مركبة وهو كمثال لتوضيح فكرة التصميم. ان خوارزمية FFT التي تم اعتمادها في هذا البحث تستخدم معمارية فراشة الاساس-4 وحسابات النقطة الثابتة. في هذا التصميم تم اختيار اسلوب الحجيرة (Booth) المتوازية في بناء دوائر الضرب المركبة المطلوبة لانجاز عمليات الفراشة (وحدة البناء الاساسية لخوارزمية ال FFT ) والتي تختصر المكونات المادية المطلوبة لتصميم دوائر الضرب قياسا للاساليب الاخرى. لقد اشارت نتاج المحاكات التي تمت باستخدام لغة VHDL و برنامج Model Sim الى ان التصميم الكامل للمنظومة يتطلب بحدود 50000 وحدة (Slices) ويمكن تنفيذها في FPGA واحدةhttps://rengj.mosuljournals.com/article_27026_db52244114588fc252444964fc43be87.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628 Implementation of Multiplier less Architectures for Color Space Conversions on FPGAتنفيذ معمارية بلا مضارب لتحويلات فضاء اللونِ على رقاقة البوابات القابلة للبرمجة حقليا891032702910.33899/rengj.2011.27029ENDr. Ahlam Fadhil MahmoodAbdulkreem Mohammad SalihJournal Article20110601Abstract
The divergence of computers, internet, and wide variety of interactive video devices, in most of the multimedia applications, all using different color representations, is forcing the digital designer today to convert between them. The objective is to have a converter, which will be useful for number of applications with a basic function of converting from one color space to another and the inverse on same architecture. This paper presents an efficient parallel multiplierless implementation for two color space converters (RGB to YCbCr and YCbCr to RGB). The proposed architecture is based on distributed arithmetic (DA) principles which has been implemented on the Xilinx Spartan-3E XC3S500 FPGA using fewer resources. The implementation approach exhibits better performances when compared with existing implementations, Modifications have been carried out in DA to reduce the hardware complexity with better performance in area, latency and throughput.
Keywords: Color Space Conversion; Distributed Arithmetic ; FPGA; Video, Processing; Image Processing .أن انتشار الحاسبات والإنترنت والأنواع المختلفة مِنْ أدواتِ الفيديو التفاعليةِ، في أغلب التطبيقاتِ المتعددة الأوساطِ،وكُلّ منها يستخدم تمثيل مختلف للألوان يُجبرُ المصممَ الرقميَ على تنفيذ معمارية للتَحويل بينهما. لذلك كان هدف البحث تصميم محول للالوان، يَكُونُ مفيد لعددِ التطبيقاتِ وظيفته ألأساسية التَحويل من فضاء لونِ إلى آخر وبالعكس في نفس المعمارية. هذه الورقةِ تقدم معمارية متوازية بدون مضارب لتحوّلين لفضاءِ اللونِ (RGB to YCbCr and YCbCr to RGB). المعماريةَ المُقتَرَحةَ مستندة على مبدأ الحساب المُوَزَّع حيث طُبّقتْ على رقاقة البوابات القابلة للبرمجة حقليا Spartan-3E XC3S500 بمكونات أقل. التطبيقُ المقترح أعطى نتائج أفضل مقَارنَة بالتطبيقاتِ الأخرى, التعديلات نفّذت في الحساب المُوَزَّع لتخفيض تعقيد المكونات بالأداء الأفضل في المساحة وتقليل معدل الحصول على ألاخراج وكمية المعلومات التي يتم معالجتها.https://rengj.mosuljournals.com/article_27029_99612f4832edb1e84e7b32fba42f5500.pdfCollege of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052619320110628Discharge Coefficient for V-Notch Broad Crested Side Weir Side Weirمعامل التصريف للهدارات الجانبية ذات الحافة العريضة بفتحة مثلثة1041112703110.33899/rengj.2011.27031ENAmal Abd Al-Ghnai YahyaJournal Article20110601Abstract
In this paper the hydraulic characteristics of V-notch broad crested side weir have been experimentally studied. Sixteen V-notch broad crest weirs were constructed with six apex angles (θ=30º, 45º, 60º, 90º, 120º,and 150º)and the apex height change three times (p=5,10,15cm) for the first forth angles and change two times for the last two angles (p=10,15cm), each model can be tested by changing flow in the main channel several times and from the analysis of experimental results it was found that the coefficient of discharge(Cd) for the V-notch broad crested weir is depend on the hydraulic and geometric characteristics of channel and weir, and from the hydraulic characteristics of the main channel it was found that the coefficient of discharge (Cd) directly proportional to the main channel Froude number before side channel , and a maximum value of (Cd) can be reached for a larger acute V-notch angle , but a maximum value of (Cd) can be reached for the smaller obtuse V-notch angle. Also from the hydraulic and geometric effect for both channel and weir it is found that (Cd) inversely proportional with (y1/p) and directly proportional with (y1/h &p/h) and a maximum (Cd ) can be reached maximum for both acute and obtuse V-notch angle. Suitable equations for discharge coefficient are obtained for different apex angle, then the predicated discharge coefficient from the equations were plotted against the calculated value with coefficient of determination (R2=0.9) and it was found to be good.
Keywords: Broad Crested Weir, Side Weir, V-Notchالملخص في هذا البحث تم دراسة الخصائص الهيدروليكية لهدار جانبي عريض الحافة بفتحة مثلثة وضع في مأخذ قناة جانبية, حيث تم إنشاء ستة عشر نموذج بزوايا مختلفة للفتحة المثلثة((θ=30º, 45º,60º,90º,120º, and 150 º وتم تغير ارتفاع الفتحة المثلثة ثلاث مرات للزوايا الأربعة الأولى (p=5,10,15cm) ومرتين للزاويتين الأخيرتين p=10,15cm)). وتم فحص كل نموذج بإمرار عدة تصاريف. ومن تحليل النتائج المختبرية وجد أن معامل التصريف (Cd) يعتمد على الخواص الهيدروليكية والجيوميترية لكل من القناة والهدار, حيث وجد من تأثير الخواص الهيدروليكية للقناة أن معامل التصريف ( (Cd يتناسب طرديا مع رقم فرود في القناة الرئيسة قبل التفرع وأن أعلى معامل للتصريف (Cd) يمكن الحصول عليه لأكبر زاوية للفتحة المثلثة الحادة وأصغر زاوية للفتحة المثلثة المنفرجة, و من تأثير الخواص الهيدروليكية والجيوميترية للقناة والهدار وجد أن معامل التصريف يتناسب عكسيا مع (y1/p) وطرديا مع (y1/h, p/h) وأعلى معامل للتصريف (Cd) يمكن الحصول عليه لأكبر زاوية للفتحة الحادة وكذلك المنفرجة. وقد وجدت علاقة لكل زاوية من زوايا الفتحة المثلثة التي تم دراستها في هذا البحث لحساب معامل التصريف (Cd) بالاعتماد على المتغيرات (F1, p/h, y1/h, and y1/p ). وقد رسمت العلاقة بين قيم معامل التصريف المقيسة والمحسوبة ولوحظ تقارب جيد مع خط التوافق حيث بلغ معامل التحديد R2=0.9)).https://rengj.mosuljournals.com/article_27031_8e5f2faa57c1ba8cd6383829d4280c7e.pdf