College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Effect of magnetic field on mixed convection in superposed Nanofluid and porous layers inside lid-driven cavityتأثیر المجال المغناطیسی على الحمل المختلط فی وسط متراکب من مائع نانوی و طبقة مسامیة داخل تجویف ذو غطاء متحرک11116432310.33899/rengj.2019.164323ENEhab AbudlaziezHamzaDepartement of mechanical Engineering, College of Engineering, University of Mosul, Mosul, IraqAbbas SaeedHussainDepartementand mechanical Engineering, College o Engineering, University of Mosul, Mosul, IraqJournal Article20190513In the present research the effect of magnetic field on the mixed convection was carried numerically in lid driven composite two dimensional square cavity ,this cavity composed of two layers : a Cu-water nanofluid layer superposed a porous media ,the porous media saturated with the same nanofuid The left and right walls are thermally insulated ,However the bottom wall which is in contact with porous media is isothermally hot while the top wall which is in contact with nanofluid layer is isothermally cold and being lid driven in constant velocity to right.<br /> The governing equations in this study were normalized and solved numerically by finite difference method. The convection term of the momentum and energy equations were treated by upwind scheme, while the diffusion and source terms were treated by central difference. Gauss-siedel iteration method were used for solution vorticity and energy equations and Successive Over Relaxation method were used for solution of stream function equation.. In this study the following parameters were considered:<br /> Hartman number (Ha) from (0 to 60), nanoparticles volume fraction (0.01, 0.03, 0.05), Richardson number (Ri) (0.1, 1, 5), Darcy number (Da) (10-3, 10-4, 10-5) and porous layer thickness (Wp) (0.3, 0.5, 0.7) at constant Reynolds number (Re=100) and Prandtl number (Pr=6.24). The results show that increasing Hartman number causes a reduction in mixed convection heat transfer and this effect reduced by increased the porous layer thickness. In increased of Hartman number from 0 to 60 with Wp (0.3, 0.5, 0.7) a reduction in convection heat transfer. Moreover an increase in Richardson number ( Ri ) enhanced the convection heat transfer for all Hartman number , Also the increase of nanoparticles volume fraction improve the heat transfer and this effect reduced as Hartman number increased. It is noticed that increasing Hartman number to 30 gives highest value of Nusselt number at lower thickness of porous layer.فی البحث الحالی اُجریت دراسة عددیة لمعرفة تأثیر المجال المغناطیسی فی الحمل المختلط فی حیز مربع ثنائی الابعاد ذی غطاء متحرک مکون من مائع نانوی (نحاس- ماء) ووسط مسامی مشبع بنفس المائع النانوی الجدار الأیمن و الایسر معزولان حراریآ بینما کان الجدار الاسفل ذو درجة حرارة ثابته وساخنة و الجدار العلوی ذو درجة حرارة ثابته باردة و یتحرک بسرعة ثابتة نحو الیمین استخدمت طریقة الفروق المحددة للحل العددی للمعادلات الحاکمة و لزیادة استقرار الحل و تحقیق حل صحیح فیزیائیا.تم استخدام طریقة upwind لتمثیل حد الحمل convection term فی معادلة الزخم و معادلة الطاقة, و استخدمت طریقة کاوس-سایدل و طریقة successive over relaxation لحل المعادلات. تم فی هذا البحث دراسة تأثیر المتغیرات الآنیة فی انتقال الحرارة بالحمل المختلط: و التی تشمل کل من عدد هارتمان 0) الى (60 و النسبة الحجمیة للجسیمات النانویة 0.01) و 0.03 و 0.05) و عدد ریکادسون 0.1) , 1 , 5) و عدد دارسی (10<sup>-5</sup>,10<sup>-4</sup>,10<sup>-3</sup>) و سمک الطبقة المسامیة (0.7,0.5,0.3) و بثبوت عدد رینولد عند (Re=100) و عدد برنتدل عند (Pr=6.24). بینت النتائج أن زیادة عدد هارتمان یؤدی إلى نقصان عدد نسلت, و الذی بدووره یوثر سلباً على الحرارة المنتقلة بالحمل, فی حین وجد ان زیادة الطبقة المسامیة یؤدی الى تقلیل تاثیر عدد نسلت, فی حین أن زیادة عدد ریکادسون یؤدی إلى زیادة انتقال الحرارة لاعداد هارتمان کلها ،و بینت النتائج ایضاً ان زیادة النسبة الحجمیة للجسیمات النانویة تحسن من انتقال الحرارة و ینقص التأثیر بزیادة عدد هارتمان.عند زیادة عدد هارتمان إلى 30 نلحظ أن أعلى قیمة لعدد نسلت تکون عند اقل سمک الطبقة المسامیة.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Evaluating the Performance of the A2O System for Removing Nutrients from Municipality Wastewaterتقییم أداء منظومة الـ A2O لازالة المغذیات من میاه الفضلات المدنیة122416433410.33899/rengj.2019.164334ENSaja Abd Al-RazzaqMohammedUniversity of Mosul, College of Engineering, Environmental EngineeringAmmar Thamir HamadUniversity of Mosul, College of Engineering, Environmental EngineeringJournal Article20190629Nitrogen and phosphorus are essential for the growth of micro-organisms used in wastewater treatment. When a treatment system is designed to remove a quantity of nutrients، larger than the ordinary metabolism requirements of bio-cell، the operation is called biological nutrient removal BNR. The BNR system consists of two processes: the biological nitrogen removal and the enhanced biological phosphorus removal (EBPR). There are several arrangements for biological nutrient removal processing. The selection of the suitable treatment scheme depends on the characteristics of the raw wastewater، quality of treated effluent required and the economical consideration. Several studies showed that the A2O system is the most suitable among different configurations because of its simplicity in operation، low oxygen requirements (i.e. low operational cost)، high efficiency of nutrient removal and a good settling characteristics of the sludge produced. A continuously flow laboratory scale of A2O was used in the current study. A raw municipal wastewater from the environmental engineering department is flowing at a rate of 0.6ml/sec. The mean cell residence time was 12 days. The experiments were conducted under three different internal cycle ratios (IR) and three returned activated sludge ratios، The effective sizes of the anaerobic، anoxic and aerobic compartments were 6.4، 8.65 and 17.21 L respectively، The results showed that the percentages of internal cycle ratio have a significant effect on the process of biological removal of nitrates while the percentage of returned activated sludge (RAS) has a significant impact on the biological removal of phosphorus. The A2O system removal efficiency of COD، orthophosphate and ammonia were: 85.7%، 93.5%، and 92.4%، respectively. The effluent quality is within the Iraqi standards with respect to organic and nutrients contents.یعتبر النتروجین والفسفور من عناصر النمو الأساسیة للکائنات الدقیقة المستخدمة فی معالجة میاه الفضلات. حیث تحصل إزالة نسبة محددة من المغذیات خلال جمیع مراحل المعالجة البیولوجیة بقدر ما یمکن ان تستوعبه کتلة الخلیة الناتجة، وعندما یتم تصمیم نظام معالجة لإزالة مغذیات أکبر من الکمیات الضروریة للتمثیل الغذائی، حینئذ یطلق على هذا النظام بالمعالجة البیولوجیة لإزالة المغذیات (Biological Nutrient Removal (BNR)). یتکون نظام BNR من عملیتین: الإزالة البیولوجیة للنتروجین والإزالة البیولوجیة المعززة للفسفور (EBPR). وهناک عدة ترتیباتِ لعملیات المعالجة البیولوجیة للمغذیات BNR تعتمد عملیة اختیار المعالجة الأکثر ملاءمة لأی نظام على خصائص میاه الفضلات الداخلة ونوعیة المیاه المعالجة المطلوبة واعتبارات الکلفة تعد منظومة الـ A2O هی الأوسع انتشارا لبساطة تشغیلها وانخفاض متطلبات التهویة (انخفاض الکلفة التشغیلیة) والجودة العالیة للحمأة الناتجة والکفاءة العالیة فی إزالة المغذیات. استخدمت میاه الفضلات المدنیة الخارجة من قسم هندسة البیئة لتجهیز نموذج الـ A2O المختبری بمعدل دفق مقداره 0.6ml/sec وبمعدل مکوث للحمأة (SRT) یقدر بـ 12d. تعمل المنظومة على ثلاث نسب مختلفة للتدویر الداخلی (IR) وثلاثة للتدویر الخارجی وکانت الأحجام الفعالة للمفاعلات اللاهوائیة وقلیلة التهویة والهوائیة L(6.4 و8.65 و17.21) على التوالی. أظهرت النتائج أن النسب المئویة للتدویر الداخلی ذات تأثیر کبیر على عملیة الإزالة البیولوجیة للنترات وتعتبر دالة لها وان العلاقة بینهما عکسیة حیث انه بزیادة نسبة التدویر الداخلی تقل ترکیز النترات فی دفق المیاه الخارج، بینما کان للتدویر الخارجی تأثیر کبیر على عملیة الإزالة البیولوجیة للفسفور وتعتبر دالة لها وان العلاقة بینهما طردیة حیث انه بزیادة نسبة التدویر الخارجی تزداد کفاءة إزالة الفسفور، بینما لم یکون لنسب التدویر الداخلی والخارجی تأثیر معنوی على کفاءة إزالة کلا من الأمونیا والـCOD ووفقًا لنتائج البحث فقد حققت منظومة الـ A2O افضل کفاءة إزالة للمواد العضویة المتمثلة بالـ COD والفسفور بشکل فوسفات أحادیة والأمونیا (85.7 %، و93.5%، و92.4)% على التوالی مع تلبیة دفق مطابق للمعایر العراقیة لتصریف میاه الفضلات إلى الأنهار لجمیع المرکبات العضویة والفسفوریة والنتروجینیة. <br /> College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201UNIFORMITY FOR PORTABLE GRID SPRINKLER SYSTEMSتأثیر تباین شحنة الضغط على تناسق توزیع الماء لأنظمة الرش الشبکیة المنقولة253816433310.33899/rengj.2019.164333ENAhmad ThamerIbrahimDepartment of water resources Engineering, College of Engineering, University of MosulHaqqi IsmailYasinDepartment of Dams and water resources Engineering,College of Engineering, University of Mosul, Mosul, IraqJournal Article20190707<em>The proper size and diameter of the lateral sprinkler pipe is associated with the variations of pressure head along the pipeline; the greatest pressure head variations, the smallest pipe size and thereby an increase in the required pressure head at the inlet of lateral pipe and the pumping power unit. The pattern of water distribution of sprinklers operating with different operating pressure will accordingly varies and may leads to variations in uniformity of water application along the lateral pipe. The research purpose is to study the effect of pressure head variation on the uniformity of the water distribution along the lateral pipe by adopting different values of the friction head losses that expressed as a fraction of average operating head, and linking with spacing between sprinkler heads. Furthermore, this study aims to compare between the increase in pumping power cost to ensure operating head at the lateral inlet associated with increase in the fraction of friction head losses, and decrease in the cost of the pipe. 18 tests were carried out to obtain the water distribution pattern for single sprinkler under different pressure heads and for five different type sprinklers,the water distribution pattern of a single sprinkler was estimated as a function of distance from the sprinkler and the pressure head with non-physical formulas and high determination coefficients. Fractions of head losses due to friction were chosen to be (10, 20, 30, 40, and 50) % of the sprinkler operating head. A computer program was developed to compute the pressure head at each sprinkle, water distribution pattern, and water application uniformity of the sprinkler network system using different sprinkler head spacing and three levels of operating heads. Also, the economics of pipe size and pumping operation cost using the selected fractions of the friction head losses was studied. </em><br /> <em>The results show that the water distribution uniformity increases when the pressure head at sprinkler head increases and this increase varies according to the sprinkler type and spacing; there is no observable change between the system water distribution uniformity and uniformity coefficient of application at the average operating pressure head for all sprinkler spacings and friction head looses fractions except the case of friction head loose equal to 50% of the operating head that showed very small differences. Also, the annual pumping cost to ensure required pressure head at lateral pipe inlet using same average operation head is constant for all used sprinkles. The total annual cost increases when the adopted friction head loose in the design of lateral sprinkler pipe increases stating that the economic pipe size is associated with low friction.</em><em>إن الاختلاف فی شحنة الضغط على امتداد أنبوب الرش یؤثر فی اختیار حجم الأنبوب فکلما زاد الاختلاف المعتمد کلما قل حجم الأنبوب وهذا یؤدی الى زیادة شحنة الضغط اللازمة فی بدایة أنبوب الرش والذی بدوره یزید من الطاقة اللازمة للضخ، وإنّ نمط توزیع الماء من المرشات التی تعمل بشحنات ضغط متباینة سوف یختلف طبقا لذلک وقد یؤدی إلى اختلاف فی تناسق الإرواء على امتداد أنبوب الرش. الهدف من البحث دراسة تأثیر تباین شحنة الضغط على تناسق توزیع الماء على امتداد أنبوب الرش وذلک باعتماد قیم مختلفة للشحنة الضائعة بالاحتکاک من معدل شحنة الضغط التشغیلیة وتداخل ذلک مع الفواصل بین المرشات، إضافة إلى المقارنة بین زیادة کلفة طاقة الضخ لتأمین شحنة الضغط الناتجة فی بدایة الأنبوب نتیجة زیادة نسبة الشحنة الضائعة بالاحتکاک والنقصان فی کلفة الأنبوب طبقاً لذلک. فقدتم إجراء 18 فحصا للحصول على نمط توزیع الماء لمرشة مفردة تحت شحنات ضغط متباینة ولخمسة مرشات مختلفة النوع، وتم تخمین نمط توزیع الماء لمرشة مفردة کدالة للبعد عن المرش وشحنة الضغط بمعادلات ذات صیغ غیر فیزیائیة وبمعاملات تحدید عالیة. وتم اعتماد فواقد الشحنة الضائعة بالاحتکاک فی أنبوب الرش بنسب 10%،20%،30%،40%،50% من معدل شحنة الضغط التشغیلیة للمرش، کما تم إعداد برنامج حاسوبی لإیجاد شحنة الضغط عند کل مرش ونمط التوزیع الحقلی لمنظومة الرش الشبکیة المنقولة وبعدة فواصل للمرشات وبثلاث مستویات لمعدل شحنة الضغط وذلک لفواقد الشحنة الضائعة بالاحتکاک وإیجاد معامل تناسق توزیع الماء للمنظومة. إضافة إلى الموازنة بین تأثیر کل من قطر الأنبوب وطاقة الضخ اقتصادیاً باعتماد النسب المختلفة أعلاه من معدل شحنة الضغط التشغیلیة.</em> <br /><em>بین البحث أن معامل تناسق توزیع الماء یزداد نتیجة زیادة شحنة الضغط عند راس المرشة وان هذه الزیادة تتباین طبقا لنوع المرش والفواصل بین المرشات. وان معامل تناسق توزیع الماء للمنظومة </em><em>UC<sub>System</sub></em><em>% لا یختلف أو یکاد یتطابق مع معامل تناسق الارواء عند معدل الشحنة التشغیلیة وذلک لکافة الفواصل بین المرشات ولجمیع حالات فواقد الاحتکاک بنسبها المختلفة ماعدا فروقات طفیفة جدا عندما تکون الشحنة الضائعة بالاحتکاک تمثل نسبة 50%. وان کلفة الضخ السنویة لتامین شحنة الضغط المطلوبة فی بدایة أنبوب الرش ثابتة لجمیع المرشات المستخدمة فی الدراسة وذلک عند نفس معدل شحنة الضغط التشغیلیة</em><em>.</em><em>وان الکلفة الکلیة السنویة تزداد بازدیاد الشحنة الضائعة بالاحتکاک المعتمدة فی تصمیم أنبوب الرش وهذا یعنی انه کلما قلتالشحنة الضائعة بالاحتکاک المعتمدة فی تصمیم أنبوب الرش یکون أوفر اقتصادیاً، وان النقصان فی کلفة الأنبوب بنقصان قطره نتیجة زیادة الشحنة الضائعة بالاحتکاک یقل مع زیادة الفاصلة بین المرشات على امتداد أنبوب الرش.</em>College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Using Intelligent Techniquesin Sustainable Buildingsاستخدام التقنیات الذکیة فی المبانی المستدامة395516435410.33899/rengj.2019.164354ENSinan MohammadTaleeDepartment of Architecture, Faculty of Engineering, University of Mosul, Mosul, IraqJournal Article20190505Intelligent techniques represent integration between building system and technology. The merge of these techniques within a building serves and eases our life. Intelligent techniques became a common concept that defines the highest levels of various standards, which determine indoor environmental health. In other words, they increase productivity, raise prosperity, as well as enhancing the efficiency of resources, cost, flexibility, and adaptability. Thus, intelligent techniques reflect the concept of sustainability, as their effects cover all the main building aspects of function, structure, and form. The study considers form as the most obvious affected aspect of a sustainable building, especially as the intelligent techniques and materials formed the building envelope.<br /> <br /> The research is conducted on case-study samples from the region of Arab Gulf, which have a hot desert climate that is similar to the third desert climate in Iraq. The study defines the research problem as The knowledge insufficiency of the formal aspect identifications (with various classifications) that affected by intelligent techniques of sustainable buildings in the hot desert climate. The research aims to determine the aspects affected by intelligent techniques of the sustainable building in general and to verify their role and impact on the formal aspect of the façade design that can achieve the sustainability standards. Further, the samples of the case-study location in the hot desert climate aim to employ results on our local architecture in Iraq particularly.<br /> <br /> The study defines its own structure and methodology in order to achieve its goals and solve the research problem, by dividing the research into several stages. Starting from defining the concept of the intelligence, and exploring previous studies to represent the theoretical framework. Then, listing the case-study samples, and measuring them using the descriptive analysis method, by analyzing the critical contexts upon the selected samples. The research concluded important points of the impact of the intelligent techniques on the formal aspect of the building. As the harsh conditions of the hot desert climate represent itself as a main challenge in the process, building protection against solar radiation and incandescent is vital. That is possible by methods of stirring, resistance, modulation, the control of the intelligence and the sustainability of the exterior materials.تعد التقنیات الذکیة تکاملاً بین منظومات المبنى والتکنولوجیا، اذ ان دمج تلک التقنیات فی المبانی وجدت لخدمتنا وجعل حیاتنا أکثر سهولة. فأصبحت التقنیات الذکیة مفهومًا شائعا یستخدم لتحقیق أعلى مستویات التحکم فی المعاییر المختلفة التی تحدد مدى صحة البیئة داخلالمبنی. اذ تعزز التقنیات الذکیة الإنتاجیة والرفاهیة وتساعد فی تحقیق فاعلیة الموارد والتکلفة والمرونة وقابلیة التکیف. لذلک فان التقنیات الذکیة فی الآونة الأخیرة اضحت متداخلةً مع مفاهیم الاستدامة، وتأثیرها على الجوانب الرئیسة للمبنى کالوظیفیة والانشائیة والشکلیة، اذ یعتبر الاخیر من اهم الجوانب المتأثرة للمبنى المستدام، وبالأخص اذا ما ارتبط الشکل بتقنیات ذکیة فی الاغلفة الخارجیة للمبنى او بالمواد الذکیة وغیرها من الامور المؤثرة على الشکل، التی تم دراسته ضمن المنطقة المحیطة بالعراق – دول الخلیج العربی-، التی یغلب علیها المناخ الصحراوی الحار المشابه لمنطقة المناخ الصحراوی الثالث فی العراق، اذ جاءت المشکلة البحثیة <strong>(القصور المعرفی الخاص بماهیة الجانب الشکلی - بتصنیفاته المتنوعة - المتأثر بالتقنیات الذکیة للمبانی المستدامة الواقعة ضمن المناطق الصحراویة الحارة). </strong>ویهدف البحثالى تحدید الجوانب المتأثرة بالتقنیات الذکیة فی المبنى المستدام بشکل عام، والتحقق من دورها وفاعلیتها على الجانب الشکلی للواجهات الخارجیة بما یحقق معاییر الاستدامة، بدراستها ضمن منطقة حارة، والاستفادة منها فی عمارتنا المحلیة بشکل خاص، ولحل مشکلة البحث وتحقیق هدفه لابد من تحدید هیکلا ومنهجا خاصا به. فتم تقسیم البحث الى عدة مراحل بدءاً من تعریف مفهوم الذکاء وطرح الدراسات السابقة وصولا الى طرح الاطار النظری، ومن ثم ادراج الامثلة التطبیقیة وقیاسها عبر منهج التحلیل الوصفی –تحلیل النصوص النقدیة للمشاریع المنتخبة-، کما استنتج البحث النقاط المهمة فی تأثیر التقنیات الذکیة على الجانب الشکلی للمبنى، اذ ان المناخ الصحراوی الحار له تحدیات فی حمایة المبنى من الظروف المناخیة القاسیة، لتلافی الاشعاع الشمسی الحار والوهاج اثناء النهار، من خلال التحریک والمقاومة والتحویر واهمیة ضبط المواد الخارجیة الذکیة والمستدامة.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Numerical Analysis of Effect of Nano-particles on Fluid Flow and Heat Transfer by Forced Convection in Channel with different traingle configurationتحلیل عددی لتأثیر جسیمات النانو فی جریان المائع وانتقال الحرارة بالحمل القسری فی مجرى یحوی مقاطع مثلثة مختلفة566416432110.33899/rengj.2019.164321ENAmmar A.MahmoodMech. Eng, Collage of Engineering , University of Mosul ,Mosul, IraqAmir S.DawoodMech. Eng., Collage of Engineering ,University of Mosul, Mosul, IraqJournal Article20190515This research presents a numerical analysis of the three-dimensional simulation of heat transfer and fluid flow incloded forced convection through a square-section channel with different ribs and the effect of addition of nanoparticles with constant heat flux up and down the channel. The single-phase approach of Nano-fluid is employed; it is assumed that the base fluid (water) and nanoparticles (Al<sub>2</sub>O<sub>3</sub>) are treated as a homogeneous mixture. The study assumes that the Nano-fluid incompressible, steady and laminar. The nanoparticles used in 25 nanometers and with volumetric concentration (1-5) %. ANSYS 18.1 FLUENT is a computational fluid dynamics (CFD) program. The finite volume method was used to solve the ruling equations. To ensure accuracy of the results, the validity was performed with previous studies of the channel and under the same boundary conditions and the result was Compatible. By using ribs at the top and bottom of the channel in two alignment inline and staggered, and five ribs per surface, and in tow shapes (triangle A and triangle B). The aspect ratio is equal to (2(. with five different values for Reynolds numbers (300, 500, 700, 900 and 1200). The results showed that triangular ribs type (A) with staggered alignment represent the optimal state of the all studied shapes and at all Reynolds numbers. The maximum value of the performance evaluation criteria (PEC) was 1.8561 and the use of Nano-fluid at a concentration of 5% compared to 1.5991 for the same channel using water only, and at Reynolds number 1200. At 5% volume concentration, the heat transfer coefficient (h) was 29.78% higher than the thermal conductivity increase of 16.48% when using only the Nano-fluid. When adding the triangular ribs type (A), the increase in heat transfer coefficient (h) is equal to (143.03%). Actually, other factors such as dispersion, Brownian motion, hermophoresis, vortex generator, and nanoparticles migration also are responsible for the enhancement of convective heat transfer.تناول هذا البحث تحلیل عددی لمحاکاة ثلاثیة الابعاد لانتقال الحرارة وجریان المائع بالحمل القسریفی قناة ذات مقطع مربع تحوی على اضلاع مختلفة الاشکال وتأثیر اضافة الجسیمات النانویة. لتدفق حراری ثابت اعلى القناة واسفلها, وقد افترضت الدراسة أن المائع النانوی یخضع لفرضیة احادی الطور إذ یعامل المائع الأساس (الماء) وجسیمات النانو (Al<sub>2</sub>O<sub>3</sub>) بوصفه خلیطاً متجانساً وأن المائع النانوی غیر قابل للانضغاط وجریانه مستقر وطباقی, وکانت جسیمات النانو المستخدمة بقطر 25 نانومتر بنسب ترکیز حجمی (1-5)%. اُستخدم برنامج (ANSYS 18.1 FLUENT) الذی هو احد برامج دینامیکا الموائع الحسابیة (CFD) وبأستخدام طریقة الحجم المحدد (finite volume method) لحل المعادلات الحاکمة. وقد دُرس فی هذا البحث تأثیر استخدام الأضلاع المختلفة وتراکیز جسیمات نانویة مختلفة فی أنتقال الحرارة وجریان المائع. باستخدام أضلاع (Ribs) اعلى القناة واسفلها بترتیبین متتالیین ومتعاقبین, وبعدد خمس أضلاع لکل سطح وبشکلین کال (المثلث نوع A والمثلث نوع B) وکانت قیمة نسبة العرض للارتفاع للاضلاع (aspect ratio) (2). عند خمس قیم مختلفة لأعداد رینولدز (300, 500, 700, 900 و 1200).بینت النتائج أن الاضلع المثلثة نوع (A) ذات الترتیب المتعاقب تمثل کأفضل حالة من بین الاشکال التی دُرست ولاعداد رینولدز جمیعها. إذ کانت اعلى قیمة لمعیار الاداء تم تحقیقها (1.8561) باستخدام المائع النانوی بترکیز 5% , مقارنة بـ (1.5991) للقناة نفسها وبأستخدام الماء فحسب، وعند عدد رینولدز 1200. وعند ترکیز حجمی 5 % کانت زیادة معامل انتقال الحرارة (h) تساوی (29.78%) وهی اکثر من زیادة الموصلیة الحراریة التی تساوی (16.48%) عند أستخدام المائع النانوی فحسب , اما عند اضافة الاضلاع المثلثة نوع (a) ذات الترتیب المتناوب وعند ترکیز حجمی 5 % کانت نسبة الزیادة فی معامل انتقال الحرارة (h) تساوی (143.03%). فضلاً عن ذلک عوامل أخرى مثل التشتت والحرکة البراونیة والترحیل الحراری ومولد الدوامات وهجرة الجسیمات النانویة التی تکون مسؤولة أیضًا عن تعزیز نقل الحرارة.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Performance Study of Concentrated Circular Channels System (Orbal) for Removing Nutrients from Domestic Wastewaterتقییم أداء نظام الـقنوات الدائریة المتمرکزةOrbal)) فی إزالة المغذیات من میاه
الفضلات المنزلیة657316432810.33899/rengj.2019.164328ENAmmar Th. HamadAl-TaiDepartment of Civil Engineering, College of Engineering, University of MosulMoamen W. FathelAl-TakDepartment of Civil Engineering, College of Engineering, University of MosulJournal Article20191018 A biological nutrient removal was investigated as a continuous flow (orbal) system to study the efficiency of system for removing phosphor and nitrogen compounds, and to predict the effect of internal and external recirculation rates on its performance. The pilot plant consisted of three concentric circular channels: outer, intermediate and inner in capacities of 24, 16.8 and 8.7 m<sup>3</sup> respectively. The last sedimentation basin has sludge return system to the outer channel. Pilot plant also has an internal cycle to return the mixed liquor from the inner channel to the intermediate one. Continues Flow was used to feed the plant with raw municipal wastewater from Al-Khadraa residential quarter at an average flow rate of 66.7 m<sup>3</sup>/day. The plant was equipped with a modified surface aeration system operating in total power equal to 0.48 kW to achieve the required dissolved oxygen concentrations in the outer, middle, and inner channels: 0.38, 1.3, and 2.4 mg /L respectively. The three-channel was operated on two levels of returned activated sludge (RAS): 60% and 80%. It has three levels of internal cycle (IR): 100%, 150% and 200%. The results showed: the total removal efficiencies of phosphorous, and ammonia were in the range of: (93.3% - 88.5%) and (93.5% - 92.4%), respectively. The results meet the Iraqi standards for wastewater disposal into rivers. This study revealed there is no significant correlation between removal efficiency of ammonia with the internal and external recirculation ratios, while the effluent phosphor concentrations significantly affected by RAS and IR ratios. This study adopted the hypothesis: the process of simultaneous nitrification and denitrification (SND) occurs in the outer channel, while the phosphorus removal by the pilot plant was performed by the mechanism of enhanced biological phosphorous removal (EBPR).أجری فی هذه الدراسة تصمیم وإنشاء وتشغیل محطة معالجة تجریبیة (Pilot Plant) تعمل بنظام الـقنوات الدائریة المتمرکزة (Orbal) لغرض دراسة کفاءة النظام فی إزالة المرکبات الفسفوریة والنتروجینیة، ودراسة تأثیر تغایر نسب التدویر الداخلیة والخارجیة على أدائها. تألفت المحطة التجریبیة من ثلاث قنوات دائریة متمرکزة: خارجیة و وسطیة وداخلیة بسعة24 و16.8و8.7 m<sup>3</sup> على التوالی، إضافة الى حوض ترسیب ثانوی مزود بمنظومة لترجیع الحمأة إلى القناة الخارجیة. کما تحتوی المحطة التجریبیة على منظومة داخلیة لترجیع میاه الفضلات من القناة الداخلیة الى القناة الوسطیة و بإستخدام نظام الدفق المستمر Continues Flow Mode لتجهیز المحطة التجریبیة بمیاهالفضلاتالمدنیةالخارجةمنمجمع شقق الخضراء السکنی وبمعدل دفق مقداره 66.7 m<sup>3</sup>/d. زودت المحطة التجریبیة بمنظومة تهویة سطحیة محورة تتکون من مجموعتین من المجاذیف المتمرکزة حول محورین افقیین یعملان بقدرة کلیة مقدارها 0.48 kW لتحقیق تراکیز الأوکسجین المذابالمطلوب تجهیزها فی القنوات الخارجیة و الوسطیة و الداخلیة والتی قدرت بـ 0.38 mg/L ،1.3 mg/L و 2.4 mg/L على الترتیب. تم تشغیل المحطةالتجریبیة بقنواتها الثلاثة على مستویین من نسب الترجیع الخارجی 60% و 80% وثلاث مستویات من نسب التدویر الداخلی 100%، 150% و 200%. سجلت المحطة التجریبیة معدلات کفاءة إزالة للمغذیات: الفسفور بشکل الفوسفات الأحادیة والنتروجین بشکل أمونیا تراوحت بین: (%93.3-%88.5)، و(92.4%- 93.5%) على التوالی مع تلبیة دفق میاه الفضلات الخارجة للمعایر العراقیة لتصریف میاه الفضلات إلى الأنهار لجمیع المرکبات الفسفوریة والنتروجینیة. کما بینت الدراسة عدم وجود علاقة بین الکفاءة الکلیة لإزالة الامونیا ونسبالتدویرالداخلیوالخارجی المعتمدة فی الدراسة فی حین تاثرت تراکیز الفوسفات الاحادیة الخارجة من المحطة التجریبیة وبشکل معنوی بنسبتی التدویر الداخلی و الخارجی معاࣧ. وقد تبنت الدراسة فرضیة حصول عملیة النترجة وعکس النترجة المتزامنة (SND) فی القناة الخارجیة بینما خضعت عملیة ازالة الفسفور فی المحطة التجریبیة الى الیة الازالة البیولوجیة المحسنة للفسفور (EBPR). <br /> College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Simulation of Cold Forming of Spur Gears using DEFORM 3Dنمذجة تشکیل المسننات ذوات الاسنان المستقیمة على البارد باستخدام DEFORM 3D748016432410.33899/rengj.2019.164324ENZainab Mohammed T.RasheedMechanical Engineering Department- College of Engineering - University of MosulMohammed NajeebAbdullahMechanical Engineering Department- College of Engineering - University of MosulJournal Article20190729In the current study, the DEFORM3D program was used to simulation of cold forming of spur gears using lead metal. Three different forms of billets were used to forming the spur gear and the choose of the size of billets was determined according to the size of suggested gear in this study. Analyzes were performed such as effect of stress, strain, average stress, total distance and speed during the formation process. Through the results of the values of the average stresses for the three billets, it was observed that the lowest value is obtained when using a solid billet. As indicated by the results of the study of the maximum stress occurs when the use of hollow billet with a diameter of 4 mm. In the study of effective stress, it was observed that there was a convergence in the stress values for all work pieces; these values in the age zone are greater than the center area. The results obtained from numerical modeling showed that the minimum effective strain occurs when using a hollow billet with a diameter of 4 mm and the highest value when using a solid billet. The velocity of the metal flow is proportional with the shape of the billet, it is noted that the value of the velocity in the case of hollow billets (4 mm and 6 mm) was close together and higher than the value of the metal flow velocity when using a solid billet. The speed of the metal flow is proportional with the amount of the billet cavity; in the case of the hard solid billet the speed is low. Peak load is affected during the formation of the spur gear with the shape of billet; it was observed that the peak load values of the 4 mm hollow billet were less than the peak load of the other two cases.فی الدراسة الحالیة برنامج ال DEFORM3D استخدم لنمذجة تشکیل المسنن ذو الاسنان المستقیمةعلى البارد مستخدماً معدن من الرصاص، تم استخدام ثلاث اشکال مختلفة لقطع عمل لتشکیل المسنن ذو الاسنان المستقیمة وان اختیار احجام هذه القطع تم بالاعتماد على حجم المسنن المقترح فی هذه الدراسة. اجریت عملیات التحلیل مثل تاثیر الانفعال ،تاثیر الاجهاد، متوسط الاجهاد ،المسافة الکلیة والسرع اثناء عملیة التشکیل. من خلال النتائج لقیم متوسط الاجهادات لقطع العمل الثلاث لوحظ ان اقل قیمة ممکن الحصول علیها عند استخدام قطعة عمل صلدة. کما لوحظ من النتائج عند دراسة اقصى اجهاد عند عملیة تشکیل المسنن یحدث عند استخدام قطعة العمل المجوفة بقطر (4 ملم). بینما لوحظ عند دراسة الاجهاد الفعال ان هنالک تقارب فی قیم الاجهاد لجمیع قطع العمل وتکون هذه القیم فی منطقة السن أکبر من منطقة المرکز. ان تأثیر الانفعال الفعال ومن خلال النتائج التی تم الحصول علیها من النمذجة العددیة تبین ان اقل انفعال یحدث عند استخدام قطعة عمل مجوفة بقطر (4 ملم) واعلى قیمة عند استخدام قطعة عمل صلدة. تتناسب سرعة تدفق المعدن مع شکل قطعة العمل، اذ لوحظ ان قیمة السرع فی حالة استخدام قطع عمل مجوفة (4 ملم و6 ملم) کانت متقاربة فیما بینها واعلى من قیمة سرعة تدفق المعدن کانت عند استخدام قطعة عمل صلدة. تتناسب سرعة تدفق المعدن مع مقدار تجویف قطعة العمل حیث انه فی حالة قطعة العمل الصلدة تکون السرعة قلیلة وفی حالة استخدام قطع العمل المجوفة تزداد نتیجة لحرکة الجزئیات لملیء تجویف القطعة. یتأثر حمل الذروة (Peak load) فی عملیة تشکیل المسنن بشکل قطعة العمل، اذ لوحظ ان قیم حمل الذروة لقطعة العمل المجوفة بقطر (4 ملم) کانت اقل من حمل الذروة للحالتین الاخریین.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Architectural Image of Mosques in terms of Historical Drawings Mental Image of Mosques in Miniature of Maqamat Al-Haririالصورة العماریة للمساجد بدلالة الرسوم التاریخیة
الصورة الذهنیة للمساجد فی منمنمات مقامات الحریری8110016432210.33899/rengj.2019.164322ENSura MohammedAdil KhaleelDepartement of Electrical Engineering, College of Engineering, University of MosulHassan MahmoodKasimDepartement of Architectural Engineering, College of Engineering, University of MosulJournal Article20190530<em>Islamic architecture (and Mosques) still the focus of attention for researchers and architects, there are continues attempts to renew the way that we look at the heritage of this architecture; to find what enrich and present new knowledge about the emergence of forms that was unique. The perception process is the most important part of architectural design process, It is the result of the designer's effort to determine the final outcome of the architectural work. This is because of the importance of the mental images that are formed in the recipient's perception of architecture he sees and lives in. </em><br /> <em> As for Mosque architecture, scarceness of evidences and researches about the perception of people (whether they were producers or recipients) who lived in buildings of Islamic architecture at old ages when it was built.</em>... <em>In order to inquest recipients of Islamic Architecture at time when it was built; the aim of this research is to analyze the historical drawings (specifically the Arab miniatures), as an aspect to reveal the mentality of the recipient of that age which considering the painter who produced it as a witness to his age by his drawings which documented his mentality (the mentality of the prevailing culture). Research procedure was to explore Moaque Architecture Factors from literature of Islamic Architecture, then to explore these factores by analyzing 12 miniatures selected from the two miniatures manuscripts of "Maqamat Al Hariri".</em><br /> <em>By the discussion of results, it became clear that the mental image of the <strong>general</strong> <strong>architectural characteristics</strong> of the mosque extracted from the miniatures is represented by focusing on the inner spaces more than the external spaces, especially facades of courtyard, mosque extended horizontally dominated by strictly symmetry, and with high diversity in the use of architectural and decorative elements, and thus be compatible with the image of the mosque in modern literature.</em><em> As for the mental image of mosque in terms of <strong>the architectural elements</strong>, it is mainly depicted as spaces with arches carried by columns with lamps hanging from them with much of decorative and secondary elements, with the presence of the mihrab, and minbar with moderate rate, minarets appeared in a few rates, while domes, doors and windows in rare rates. Thus this mental image of the mosque at that time realizes the architectural elements in rates that differ from what modern literature provides, specially about the importance of minarets and domes.</em><em>لازال نتاج العمارة الاسلامیة ومن ضمنها المساجد محط انظار الباحثین والمصممین المعماریین والمحاولات مستمرة فی تجدید الاسلوب الذی ینظر به الى تراث هذه العمارة لإیجاد ما یغنی ویقدم الجدید حول ظهورها بالهیئة التی تفردت وعرفت بها. وتعد عملیة التلقی الرکن الاهم فی العملیة التصمیمیة, فهی ثمرة جهد المصمم وبها تتقرر النتیجة النهائیة للعمل المعماری وذلک لأهمیة الصور الذهنیة التی تتکون فی ادراک المتلقی ازاء العمارة فهی المعبر عن فهمه وقراءته لها.</em> <br /><em> وفیما یخص عمارة المساجد هناک ندرة فی الدلائل والبحوث عن نظرة الناس الذین ارتادوها وشاهدوها (منتجین أو متلقین) من المعاصرین لها وقت بنائها, ولأجل استنطاق المتلقین لعمارة المساجد من الذین عاصروا بناءها , هدف البحث الى تحلیل الرسوم التاریخیة (تحدیدا المنمنمات العربیة) التی صورت المساجد وسیلة للکشف عن ذهنیة المتلقی المعاصر لها متمثلا بالرسام الذی انتجها من خلال رسومه التی وثقت ذهنیته (ذهنیة الثقافة السائدة) عنها.... باعتبار فنانی المنمنمات من المتلقین لنتاج العمارة الاسلامیة وقت بنائها. خطة البحث تضمنت استخلاص مفردات عمارة المساجد من أدبیات العمارة الاسلامیة، ثم استخلاص نتائج تحلیل 12 منمنمة تم انتخابها من المخطوطات الخاصة بمقامات الحریری المصورة</em><em> (القرن 11 میلادی) </em><em> من قبل الفنان الواسطی والفنان الذی رسم المخطوطة المحفوظة فی سان بطرسبورغ .</em> <br /><em> تبین من من مناقشة النتائج</em><em>أن الصورة الذهنیة للخصائص العماریة العامة للمسجد المستخلصة من المنمنمات تتمثل بالترکیز على الفضاءات الداخلیة اکثر من الخارجیة وخاصة المصورة للمشهد کواجهة من الفناء وهی ممتدة أفقیا یهیمن على تکوینها تناظر صارم, وذات تنوع عالی فی استخدام العناصر العماریة والزخرفیة, وبذلک تکون متوافقة مع صورة المسجد فی الأدبیات الحدیثة.</em><em>أما الصورة الذهنیة للمسجد من حیث العناصر العماریة المکونة للمسجد تتمثل فی تصوره بالأساس کفضاءات لها عقود محمولة على أعمدة مع القنادیل المتدلیة منها مع کثرة العناصر الثانویة التزیینیة (الشرافات والمحجرات) ویتوسط المحراب هذا المشهد على الاغلب، مع وجود المنبر بنسبب متوسطة، ظهرت المآذن بنسب قلیلة ، بینما القباب والأبواب والشبابیک بنسب نادرة.وهذه الصورة الذهنیة للمسجد آنئذ تدرک العناصر العماریة بنسب تختلف عما تقدمه الأدبیات الحدیثة عن أهمیة المآذن والقباب.</em>College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Effect of Impact Velocity and Angle on Erosion Behavior for Polymeric Composite Materialsتأثیر سرعة وزاویة الصدم على سلوک التعریة للمواد البولیمریة المتراکَّبة10111416432610.33899/rengj.2019.164326ENAhmed W.KhalidMechanical Engineering, College of Engineering, University of Mosul, Mosul-IRAQAbdullhaqq A.HamidDepartment of Mechanical Engineering, College of Engineering, University of Mosul, Mosul-IRAQJournal Article20191013<em>Due to significant effect of the phenomenon of erosion and its entry in many engineering and industrial applications, hence the importance of the study of erosion, especially the key factors of impingement velocity and impingement angle, because of their high effect on the phenomenon of erosion. The erosion testing device was manufactured according to ASTM G76 specifications, and devices rotating molds casting and vacuum equipment were manufactured, and unsaturated polyester specimens and its composites were reinforced with two types of reinforcing materials silicon carbide particles (SiC) and fiberglass (5 wt. %) and (44%. wt. %) respectively. The impingement velocity (25.2, 33 m / s) and impingement angles (30°, 60° and 90°) affecting erosion were studied. From the results obtained, it is noted that the behavior of polyester was brittle behavior and the composites behaves semi-ductile. And that the maximum erosion rate of polyester is at an impingement angle (90°) and the maximum erosion rate of polyester composites is at an impingement angle (60°). Silicon carbide particles improved erosion resistance at the impingement angles (90°, 30°), but at an angle (60°) they reduced pure polyester resistance to erosion, while fibers increased the rate of erosion. It was noted that the relationship between the impingement velocity and the rate of erosion is a direct relationship and that the effect of increasing the impingement velocity on the angle of impingement (60°) is greater than its impingement on the angles (90°, 30°).</em><em>نظراً للتأثیر الملحوظ لظاهرة التعریة ودخولها فی کثیر من التطبیقات الهندسیة والصناعیة , فمن هنا أتت أهمیة دراسة التعریة وبالأخص عاملی سرعة الصدم وزاویة الصدم وذلک لتأثیرها الواضح على ظاهرة التعریة. فتم صناعة جهاز فحص التعریة حسب مواصفات (</em><em>ASTM G76</em><em>), وصناعة جهازی تدویر قوالب الصب وتفریغ الهواء, وصناعة نماذج البولستر الغیر المشبع ومتراکباتهِ المعزَّزة بنوعین من المواد المعزٍّزة (حُبیبات کربید السیلیکون (</em><em>SiC</em><em>) والألیاف الزجاجیة) بنسبة (</em><em>5 wt.%</em><em>) و(</em><em>44 wt.%</em><em>) على التوالی. وتم دراسة عاملی سرعة الصدم (</em><em>25.2 ,33 m/s</em><em>) وزاویا الصدم (</em><em>30°, 60° and 90°</em><em>) المؤثرة على عملیة التعریة. ومن النتائج المستحصلة یلاحظ أنَّ سلوک البولستر هو سلوک هش وسلوک متراکَّباتِه یکون شبه مطیلی, وأن أقصى معدل تعریة للبولستر یکون عند زاویة صدم (°</em><em>90</em><em>) وأقصى معدل تعریة لمتراکَّبات البولستر تکون عند زاویة صدم (°</em><em>60</em><em>). وإنّحُبیبات کربید السیلیکون حسّنت من مقاومة البولستر النقی للتعریةعند زاویتا الصدم (</em><em>30°,90°</em><em>) لکن عند الزاویة (°</em><em>60</em><em>) خفضت من مقاومة البولستر النقی للتعریة, أمّا الألیاف فرفعت من معدل تعریة البولستر عند جمیع الزوایا المدروسة. ویلاحظ أنَّ العلاقة بین سرعة الصدم ومعدل التعریة علاقة طردیة وأنَّ تأثیر زیادة السرعة على زاویة الصدم (</em><em>60°</em><em>) أکبر من تأثیرها على الزاویتین (</em><em>30°,90°</em><em>).</em>College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Manufacturing of Erosion Measuring Rig for Polymers and Their Composites with some Experimental Resultsتصنیع جهاز قیاس التعریة للمواد البولیمریة ومتراکَّباتها مع بعض النتائج التجریبیة11512916432710.33899/rengj.2019.164327ENAhmed W.KhalidMechanical Engineering, College of Engineering, University of Mosul, Mosul-IRAQAbdullhaqq A.HamidDepartment of Mechanical Engineering, College of Engineering, University of Mosul, Mosul-IRAQJournal Article20191013<em>Solid Particle Erosion System was manufactured as a laboratory and according to the ASTM G76 specifications in a horizontal position with a feeder screw, as the system consists of the main parts: air compressor, voltage regulator, and rubber connection hoses. And the main parts of the rig: nozzle, screw, DC motor, transmission pipes, and Installation platform. The nozzle was made of low alloy steel and hardened by water-quenching, and the conical nozzle cavity was made to insert sand into the nozzle barrel. Tolerance was chosen between the screw and cylinder in practice, with a tolerance of (4 mm) out of two experiments that were tried (2, 4 mm). So, the tolerance was chosen based on the used particles (erodent) in different ranges (150-350 µm), (350-500) µm) and (500-710 µm), preferably a tolerance that gives a smooth spin rotation. One of the things to consider is the stability of the sand flow rate and the issue of overflow or vice versa is the occurrence of a stop flow, and taking into consideration the calibration between the spin rotation and the pressure of the air. Also, the sizes of sand particles used can determine several things, including tolerance, the diameter of the nozzle barrel, and the velocity of particles that can be taken. The rig was tested for specimens of unsaturated polyester (UP) and its composites reinforced with (5 wt. %) of silicon carbide, where the experiment was carried out at an impingement velocity (25.2 m / s) and impingement angles (30°, 60°, 90°) and the size of the erodent from sand Silica has a size of (350-500 µm), so the results showed that the polyester gave the highest erosion rate at the angle (90°), which indicates its brittle behavior, while its composites gave the highest erosion rate at the angle (60°), which indicates its semi-ductile behavior. It is comparing the results obtained with previous research that shows that the rig gave positive results, and it can measure the rate of erosion of polymeric materials and their composites</em><em>.</em><br /> <em>تم تصنیع منظومة فحص سلوک التعریة بالحُبیبات الحاکة (</em><em>Solid Particle Erosion</em><em>) مختبریاً وحسب مواصفات (</em><em>ASTM G76</em><em>) ذی الوضعیة الأفقیة بمغذی من النوع اللولبی (</em><em>feederscrew</em><em>),إذ تتکون المنظومة من الأجزاء الرئیسیة: ضاغطة هواء, منظم فولتیة, وخراطیم توصیل مطاطیة. واجزاء اساسیة للجهاز: القاذف, واللولب, ومحرک تیار مستمر, وانابیب نقل, ومنصة تثبیت. فقدتم صناعة القاذف (</em><em>nozzle</em><em>) من سبیکة الفولاذ المنخض (</em><em>low alloy steel</em><em>) وتمت تقسیته بطریقة (</em><em>water-quenching</em><em>), وتم عمل تجویف القاذفالداخلی مخروطی الشکل لیعمل على ادخال الرمل الى ماسورة القاذف. وتم اختیار السماحة (</em><em>tolerance</em><em>)بین اللولب والاسطوانة عملیاً بسماحة (</em><em>4 mm</em><em>) من اصل سماحتین تمت تجربتهما (</em><em>2,4 mm</em><em>), فتم اختیار السماحة على اساس الحُبیبات المستعملة (</em><em>erodent</em><em>) بمدیات مختلفة (</em><em>150-350 µm</em><em>)و(</em><em>350-500 µm</em><em>) و(</em><em>500-710 µm</em><em>), فافضل سماحة التی تعطی سلاسة بدوران اللولب. ومن اهم الامور التی یجب مراعاتها هی ثبات معدل تدفق الرمل, ومسألة التدفق العالی (</em><em>over flow</em><em>) او العکس هو حدوث توقف للتدفق, ومراعاة المعایرة بین دوران اللولب وضغط الهواء المسلط. واخذ بنظر الاعتبار احجام حُبیبات الرمل المستخدم لتحدید عدةامور منها السماحة وقطر ماسورة القاذف والسرع التی یمکن اخذها. وتمت تجربة الجهاز لنماذج من البولستر الغیر المشبع ومتراکَّباته معزَّزة بنسبة (</em><em>5 wt.%</em><em>) من کربید السیلیکون, حیث تمت التجربة عند سرعة صدم (</em><em>25.2 m/s</em><em>) وزوایا صدم (</em><em>30°,60°,90°</em><em>)وحجم حُبیبات حاکة من رمل السیلیکا بحجم (</em><em>350-500 µm</em><em>), فکانت النتائج ان البولستر اعطى اعلى معدل تعریة عند الزاویة (</em><em>90°</em><em>) مما یدل على سلوکه الهش, بینما اعطى متراکَّبه اعلى معدل تعریة عند الزاویة (</em><em>60°</em><em>) مما یدل على سلوکه الشبه مطیلی. ومن مقارنة النتائج المستحصل علیها مع بحوث سابقة تبین ان الجهاز اعطى نتائج ایجابیة, ویمکن ان یقیس معدل التعریة للمواد البولیمیریة ومتراکَّباتها.</em>College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Effect of Irrigation Scheduling Using CROPWAT on Water Use Efficiency and Grain Yield and Components for Maize (Zea mays L.) in Semi Arid Regionsتأثیر جدولة الری باستخدام برنامج CROPWAT على کفاءة استخدام المیاه والحاصل ومکوناته للذرة الصفراء (Zea mays L.) فی المناطق شبه الجافة13013716432910.33899/rengj.2019.164329ENAhmed AzhorThanoonTechnical Institute of Mosul- Northern Technical UniversityJournal Article20191109<em>Irrigation scheduling is determining the appropriate time and quantity of irrigation to reach maximum production. In this research the irrigation scheduling was determined using a computer program CROPWAT , developed by FAO . The program used the climate , crop , and soil data for calculation the irrigation scheduling .The climate data represents average years (1971-2007) of pan evaporation to Mosul city for calculating the reference evapotranspiration , maize crop and light soil data , were used to input data . The program was used cases include three different irrigation timing levels are 100%, 70% and 50% of the readily soil moisture depletion(critical depletion and belowcritical depletion) with refill soil moisture content to field capacity . The results of irrigation scheduling from the program were applied to the field experiment in the Mosul Technical Institute during the summer of 2010. The grain yield and components were measured at harvest to improve the best irrigation scheduling for maize crop in semi arid regions .</em><br /> <em>The results showed that the depth of irrigation added to three different irrigation levels 100% and 70% and 50% of the readily soil moisture depletion reached 860 and 881 and 900 mmrespectively, the number of irrigations 15, 21, 29 . The results also showed that the best irrigation scheduling for higher water use efficiency was0.55 kg/m3 and highest production356g/m2 for the treatment of 70% of the readily soil moisture depletion. Therefore the CROPWAT is aneffective tool for planning and management of irrigation maize in semi arid regions .</em><em>جدولة الری هی اختیار الوقت وکمیة المیاه المناسبة للوصول إلى أقصى إنتاج . فی هذا البحث تم حساب جدولة الری باستخدام برنامج </em><em>CROPWAT</em><em> التابع لمنظمة الأغذیة والزراعة </em><em>FAO</em><em> الذی یعتمد فی تشغیله توفر بیاناتعن المناخ والمحصول والتربة . تم تطبیق البرنامج على بیانات مناخیة تمثل معدل التبخر الانائی لمدینة الموصل وللسنوات (</em><em>1971</em><em>-</em><em>2007</em><em> ) لحساب التبخر-نتح المرجعی وإدخالها کقیم جاهزة ، وعلى محصول الذرة وتربه ذات نسجه خفیفة . تم استخدام البرنامج لحساب جدولة الری تتضمن ثلاثة مستویات مختلفةلتوقیت الری هی حین یصل استنزاف رطوبة التربة إلى</em><em>100</em><em>% و</em><em>70</em><em>% و</em><em>50</em><em>% من الماء المتاح (الاستنزاف الحرج والاستنزاف الأقل من الحرج ) مع عودة رطوبة التربة إلى السعة الحقلیة عند إضافة الری. وتم فی هذا البحث تطبیق نتائج جدولة الری من البرنامج فی تجربة حقلیة فی المعهد التقنی الموصل خلال صیف </em><em>2010</em><em>،وتم قیاس الحاصل ومکوناته عند الحصاد لتخمین أفضلجدولة ری لمحصول الذرة فی المناطق شبه الجافة.</em> <br /><em>أظهرتالنتائجبان عمق الری المضاف لمعاملات </em><em>100</em><em>% و</em><em>70</em><em>% و</em><em>50</em><em>% منالماءالمتاحبلغ 860 و881 و900 ملم على التوالی بعدد ریات </em><em>15</em><em> ، </em><em>21</em><em> ، </em><em>29</em><em> . وان أفضل جدولة ری للحصول على أعلىکفاءةاستخدامالمیاه</em><em>0.55</em><em>کغم/م</em><em>3</em><em>وأعلىإنتاجللمحصول</em><em>356</em><em>غم/م</em><em>2</em><em>کانتللمعاملةالری</em><em>70</em><em>% منالماءالمتاح . لذلک یعتبر برنامج </em><em>CROPWAT</em><em> أداة فعالة للتخطیط وإدارة میاه الری لمحصول الذرة فی المناطق شبه الجافة .</em>College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201The Situation Of Water Treatment Plant In Mosul Cityواقع محطات اسالة الماء فی مدینة الموصل13814516433010.33899/rengj.2019.164330ENMusab AbduljabbarAl-tamirEnvironmental engineering department, College of Engineering, University of MosulJournal Article20191124<strong>Abstract</strong><br /> <em>The present paper dealt with the evalution of quantiy and qualtiy of water treatmetn plants WTPs withen Mosul city. According to the total productivity of WTPs the per capita share of water was 785 L/d, and after subtracting the losses and violation upon the water supply network that reaches upto 50% the per capita portion of water becomes 392 L/d. For the quality of water; the study revealed that there are a segnificant effect of the WTPs processes upon the water quality parameters of the product water comparing with the raw water, and the quality of product water is withen the Iraqi dirnking water spicifications regarding to the parameters taken into account withen the study. This study concentric to the turbidity removal by WTPs because these plants are designed to reduce the turbidity of water to acceptable levels withen the Iraqi specification. turbidity of water is out of the specification in 13% of the samplise with different portions through the WTPs, but the highst was at aldanadan and alsaheroon plants.</em><br /> <em>Duncn test revealed that there are a significant different betweent the average of the residual turbidity and between the average of percentage removal of turbidity between WTPs and the worest plant from the residual turbidity are alsaheroon, alghzlani and aldanadan. And the woreste plant from the percent turbidity removal are alaiser aljadeed and alaiser altawsie.</em>تناولت الورقة الحالیة تقییم محطات الاسالة داخل مدینة الموصل من ناحیة کمیةونوعیة الماء المنتج؛ بلغت کمیة الماء المنتج لکل فرد785لتر\یوم اعتمادا على الطاقةالانتاجیة لهذه المحطات، وعند طرح فواقدالتکسرات والتجاوزات على الشبکة تکون حصةالفرد 392 لتر\یوم، لکن توزیع هذه الحصة غیر منتظم خلال شبکة الاسالة. اما فیما یتعلق بنوعیة الماء المنتجوجد تأثیر معنوی لعملیات المعاملة على خصائص الماء المنتج بالمقارنة مع الماء الخام وکانت خصائص الماء المنتج ضمن المواصفة العراقیة لماء الشرب للخصائص المشمولة فی هذه الدراسة، رکزت الورقة على عکورة الماء کون ان محطات الاسالة فی مدینة الموصل مصممة للتقلیل من العکورة الى المستویات الملائمة للشرب،وبلغت نسبت تجاوزات العکورة للمواصفة العراقیة 13% وعلى تفاوت بین محطات الاسالة کانت اعلاها فی محطتی الدندان والساهرون. <br />اثبت اختبار دنکن وجود فرق معنوی بین محطات الاسالة فی معدلات العکورة المتبقیة فی کل منها ومعدلات نسب ازالة العکورة فی هذه المحطات وکانت المحطات الاسواء من ناحیة العکورة المتبقیة محطات الساهرون والغزلانی والدندان على الترتیب أما من ناحیة نسبة العکورة المزالة فکانت المحطات الاقل کفاءة محطتی الایسر الجدید یلیها الایسر التوسیع.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Automated Segmentation of Retinal Blood Vessels using Fast Marching Method and local mathematical analysisالکشف الآلی للأوعیة الدمویة لشبکیة العین باستخدام منهجیة السیر السریع والتحلیل الریاضی الموضعی1916432510.33899/rengj.2019.164325ENHebat_allah Abd-AlazizAlkhaddourAlbaath university\SyriaJournal Article20190530<em>In this work, Fast Marching Method (FMM) has been suggested for Retinal blood vessels segmentation. FMM is an optimization technique; and the main advantage of the FMM is its ability to deal with branches and bifurcations without any additional computational cost. This advantage had been used in robotics to find the optimal path for the robot to move from the starting point to the goal with no collisions. Considereing the tree structure of blood vessel, I will use FMM to find the shortest bath between the optic disk and the blood vessels ends to draw the tree of the blood vessels.This method has been implemented using the M language in MATLAB R2016b. In this work local mathematical analysis has been implemented so that we can have an initial estimation of blood vessels distribution in an image in order to minimize the huge amount of noise included in retinal images and to make FMM implementing easier. FMM performance had been compared to other techniques used for retinal blood vessel detection like “Matched Filters”. The results showed that the FMM performance overcame some of those techniques and close to other high resolution methods. The FMM algorithm has been validated using the well-known “DRIVE” database and the resulting resolution ranged between 80% to 93% (depending on the noise amount in image) with iteration number between 500 to 1000 (according to the optic disk position in the image) with an average time of 0.57 seconds for each iteration which mean that the total running time is 5-10 minutes. FMM had also been validated using STARE data set and achieved a TPR of 90% for 700x605 STARE images in 15 minutes, and a TPR of 86% in 2.6 minutes when reducing image size to 350x303.</em>فی هذا العمل اقترحت خوارزمیة السیر السریع (Fast marching method-FMM) لکشف الأوعیة الدمویة فی شبکیة العین. تعتبر تقنیة FMM تقنیة أمثلة وهی تمتاز بقدرتها على التعامل مع الفروع والتشعبات بسهولة دون أیة تکلفة حسابیة إضافیة حیث تم استخدام هذه المیزة من قبل فی مجال الروبوتات لإیجاد المسار الأمثل للروبوت لیتحرک من المنطلق إلى الهدف دون أیة تصادمات. وبما أن شجرة الأوعیة الدمویة لشبکیة العین تأخذ شکلا مشابها لتعرجات الطرقات وتفرعاتها فقد وجدنا أن استخدام تقنیة FMM سیکون مفیدا ً لإیجاد المسار الأقصر بین القرص البصری وأطراف الأوعیة الدمویة بحیث نستطیع رسم شجرة الأوعیة الدمویة لشبکیة العین بسهولة. من الجدیر بالذکر أنه تم تطبیق هذه الطریقة باستخدام لغة M فی ماتلاب 2016 حیث قمنا فی البدایة بتطبیق عملیة تحلیل ریاضی موضعی للحصول على تخمین أولی لتوزع الأوعیة الدمویة فی الصورة بغیة تخفیض الضجیج الکبیر المضمن فی صور الشبکیة ولتسهیل تطبیق تقنیة FMM لاحقا ً. کما تمت مقارنة تقنیة السیر السریع مع بعض التقنیات الأخرى المستخدمة فی کشف شجرة الأوعیة الدمویة مثل "مرشحات المطابقة –matched filters" حیث أظهرت النتائج أن تقنیة FMM تفوقت على عدد من هذه التقنیات کما کانت نتائجها مقاربة لتقنیات أخرى ذات دقة عالیة. تم التحقق من أداء تقنیة FMM باستخدام قاعدة البیانات "DRIVE" حیث تراوحت دقتها ما بین 80% و93% (بحسب الضجیج فی الصورة) بعدد تکرارات یتراوح ما بین 500 تکرار و 1000 تکرار (بحسب موضع القرص البصری فی الصورة) بزمن وسطی یعادل 0.57 ثانیة لکل تکرار مما یعنی زمن تشغیل یتراوح ما بین 5 إلى 10 دقائق. کما تم استخدام قاعدة بیانات "STARE" أیضا فی عملیة التحقق من الأداء حیث حصلنا على دقة تصل إلى 90% من أجل صور STARE التی مقاسها 700x605 خلال 15 دقیقة ودقة تصل إلى 86% بزمن 2.6 دقیقة عند إنقاص الدقة إلى 350x303.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Investigation of Local Scour Around Group Bridge Pier with Different Shapesدراسة النحر حول دعامات الجسور باشکال مختلفة102216435510.33899/rengj.2019.164355ENTahseen A.GELMIRANDams and Water Research Center, Mosul University, Mosul, Iraq.Khalil I.OthmanDams and Water Research Center, Mosul University, Mosul, Iraq.Mustafa GUNALCivil Engineering, Gaziantep University, Gaziantep, TurkeyJournal Article20190417In this study, the establish on laboratory experiments for computing the depth of local scour (d<sub>s</sub>) around group bridge pier. For this purpose, fifteen models of bridge piers were constructed and tested, divided into five groups, of each group containing three bridge piers with the same specifications. The diameter of upstream bridge piers (D<sub>1</sub>) was varied to 2, 4, 6, 8, and 10 cm, and diameter of downstream bridge piers (D<sub>2</sub>) 10 cm for all. The spacing (S) between the bridge piers was varied three times 20, 30, and 50 cm for all groups. Considering the effectiveness study of upstream flow conditions, the size of diameters of bridge piers, the spacing between bridge piers and medium size of bed material on the maximum scour depth and scour pattern around bridge piers. The study was conductedby employing a physical hydraulic model for bridge piers operated below subcritical flow, clear-water condition and exploitation uniform cohesionless sand as bed material. The experimental results showed the scour depth (d<sub>s</sub>) increasing whenever increasing the upstream diameter (D<sub>1</sub>) of bridge pier and decreasing whenever decreasing the spacing (S) between bridge piers. The dimensional analysis techniques and statistical program were used for locating a new empirical formula with the facilitate of the experimental information; this formula is for calculating the maximum scour depth at bridge piers.تم فی هذه البحث اجراء دراسة مختبریة لقیاس عمق النحر الموضعی (d<sub>s</sub>) حول عدة مجامیع من دعامات الجسور. لهذه الغایة تم تصنیع وفحص خمسة عشر نموذج من دعامات الجسور مقسمة الى خمسة مجامیع کل مجموعة تحتوی على ثلاثة دعامات لها نفس المواصفات. قطر الدعامة فی مقدمة(D<sub>1</sub>)تم تغییره (2,4,6,8,10) سم, بینما قطر الدعامة فی المؤخرة (D<sub>2</sub>)بقی ثابتا لجمیع النماذج المستخدمة فی الدراسة (10) سم و المسافة بین الدعامات (S)تم تغییرهاثلاث مرات ( 20, 30, 50 ) سم على التوالی لکل مجموعة. <br />تم دراسة خصائص الجریان وقطر مقدمة الدعامة والمسافة بین الدعامات وحجم حبیبات تربة القعر مع اکبر عمق للنحر حول هذه العامات وتم التوصل من خلال النتائج العملیة ان عمق النحر یزداد بزیادة قطر مقدمة الدعامة ویقل کلما قلت المسافة بین الدعامات ومن خلال التحلیل البعدی واستخدام برنامج احصائی تم التوصل الى معادلة وضعیة لحساب اکیر عمق للنحر حول دعامات الجسور.College of Engineering, University of Mosul, IRAQAl-Rafidain Engineering Journal (AREJ)1813-052624220191201Real-Time Voice Transmission over Wireless Sensor Network (VoWSN) based Automatic Speech Recognition (ASR) Techniqueنقل الصوت بالزمن الحقیقی عبر شبکة المتحسسات اللاسلکیة باستخدام تقنیة تمییز الکلام التلقائیة233516433510.33899/rengj.2020.126441.1005ENIna`am FathiComputer Eng. Dept., Mosul UniversityQutaiba IbrahimAliComputer Engineering Dept., College of Engineering, Mosul University0000-0002-0640-0561Jassim M. Abdul-JabbarDept. of Computer Engineering, College of Engineering, University of Mosul, Mosul, Iraq.Journal Article20191228In this paper an efficient Real-Time Voice over Wireless sensor network (VoWSN) platform based on Automatic Speech Recognition (ASR) system to be used in emergency scenarios is proposed, implemented and evaluated. The workflow principle of the proposed system is depending on a Category Transformation Protocol (CTP) that transforms system category gradually from network dependent ASR system with a full dictionary and language model (i.e. large vocabulary) to fully embedded ASR system with customized dictionary and language model (i.e. small vocabulary ). Moreover, a comparison study has been performed between our proposed VoWSN based ASR system and a VoWSN based streaming system. This comparison is performed to elaborate the gains achieved when sending the text of the voice signal instead of sending the voice signal. Additionally, the Voice over IoTs (VoIoTs) system has been evaluated utilizing Voice streaming or ASR system to evaluate the system performance when connecting to the Internet.فی هذا البحث ، یتم اقتراح وتنفیذ وتقییم شبکة فعالة فی الوقت الحقیقی لشبکة استشعار الصوت عبر الإنترنت (VoWSN) تعتمد على نظام التعرف التلقائی على الکلام (ASR) لاستخدامه فی سیناریوهات الطوارئ. یعتمد مبدأ سیر العمل فی النظام المقترح على بروتوکول تحویل الفئة (CTP) الذی یحول فئة النظام تدریجیًا من نظام ASR المعتمد على الشبکة مع نموذج کامل للغة واللغة (أی مفردات کبیرة) إلى نظام ASR مضمن بالکامل مع قاموس مخصص ولغة نموذج مخصصین (أی المفردات الصغیرة). علاوة على ذلک ، تم إجراء دراسة مقارنة بین نظام ASR المقترح القائم على VoWSN ونظام البث المستند إلى VoWSN. یتم إجراء هذه المقارنة لتوضیح المکاسب المحققة عند إرسال نص الإشارة الصوتیة بدلاً من إرسال الإشارة الصوتیة. بالإضافة إلى ذلک ، تم تقییم نظام Voice over IoTs (VoIoTs) باستخدام الدفق الصوتی أو نظام ASR لتقییم أداء النظام عند الاتصال بالإنترنت.